WARNING TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS EQUIPMENT TO RAIN OR MOISTURE. DO NOT REMOVE COVER, NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE ENGINEER. DISCONNECT FROM MAINS SUPPLY WHEN NOT IN USE FOR LONG PERIODS. POWER SOURCES AC 110-240 Volts 50Hz or DC 12 Volts Only WARNING...
POWER button SKIP button CHANNEL UP/DOWN buttons REMOTE CONTROL Ensure that the POWER ( MENU button SLEEP button VOLUME control buttons ) button on the television is in the ON position before attempting ∞ POWER QUICK VIEW CH CALL SLEEP MUTE –...
REMOTE CONTROL BATTERY INSTALLATION Use two "UM-4" size batteries. Slide the cover in the Load the two batteries direction of the arrow as shown below. and remove. NOTE: Your TV will not work in the following cases. Check them carefully. If direct sunlight or other strong light is shining on the remote control sensor.
ANTENNA CONNECTIONS Connect the cable from the outdoor or indoor antenna to the antenna jack on the rear panel as shown below. For all antenna circuit problems, please consult your local dealer. A twin-lead telescopic antenna is supplied with the unit. Insert the antenna post into the mounting hole on the back cabinet until it locks into place.
SETTING LANGUAGE This TV has 5 different languages for MENU set up which can be selected through ON Screen Display: English, German, French, Italian or Spanish. To select the desired language, English (ENGLISH), Spanish (ESPANOL), French (FRANCAIS), German (DEUTSCH) or Italian (ITALIANO), press the SET UP or DOWN button.
PRESETTING THE CHANNELS After connecting, preset the desired channel (up to 110 channels) in the following procedure. There are two types of station presettings you may choose from: - Automatic tuning All stations will be preset in sequence available in your area. - Manual tuning You activate the auto search function until your preferred station is tuned in.
Page 10
PRESETTING THE CHANNELS MANUAL TUNING - How to tune a station to channel 10 position. Press the MENU button. Press the SET UP or DOWN button to select the CH TUNING mode, then press the ENTER button. MENU ENTER CLOCK SET ON/OFF TIMER SET CH TUNING PICTURE...
Page 11
Press the SET UP or DOWN button to select channel position No.10, then press the ENTER button. ENTER CH 10 When all desired channels have been set in your required position, press the MENU button three times to return to normal TV screen. MENU Repeat step 3 through 4 until all the required channels have been stored.
Page 12
PRESETTING THE CHANNELS TO CHANGE THE CHANNELS EXAMPLE: Changing of channel position from CH2 to CH5. Press the MENU button. Press the SET UP or DOWN button to select the CH TUNING mode, then press the ENTER button. MENU CLOCK SET ENTER ON/OFF TIMER SET CH TUNING...
TV OPERATIONS After completing the connection and presetting the channels, follow these steps for viewing. Press the POWER button on the TV. Then press POWER button on the remote control to turn off (STAND BY indication will light up) or on (STAND BY indication will goes off).
SETTING THE CLOCK This TV set is fitted with a 24 hr. CLOCK/TIMER. This clock controls all timed functions and the clock should be set to the correct time immediately. EXAMPLE: If you want to set the time 12:34. Press the MENU buton. MENU To set the present time, press the SET UP or DOWN button to set...
SETTING THE ON / OFF TIMER The built-in timer function allows the TV to automatically switch 'ON' (or 'OFF') of up to 4 programs daily. If you program the ON TIMER once, the TV will automatically turns on daily at the same time and to the same channel (If you program the OFF TIMER once, the TV will be turned off daily at the same time).
Page 16
SETTING THE ON / OFF TIMER Press the SET UP or DOWN button to set the desired minute, then press the ENTER button. ENTER ON TIMER 7: 30 CH 1 CANCEL 0: 00 CH 1 CANCEL 0: 00 CH 1 CANCEL 0: 00 CH 1...
CONVENIENT FUNCTIONS The following functions are available from the remote control handset only. TV/AV Selection For receiving the desired signal: Press the AV select button to select the TV or AV mode. QUICK VIEW This button allows you to go back to the previous channel by pressing the QUICK VIEW button.
Page 18
CONVENIENT FUNCTIONS MUTE When the MUTE button is pressed, the TV sound system will be turned off completely. To disable this function, press the button again. To control the volume, press VOLUME UP/DOWN. MUTE SLEEP To set the sleep timer, press the SLEEP button on the remote control. The timer will change in step of 10 minutes each time the button is pressed in the order of 120, 110, 100,...20, 10, 0.
PICTURE CONTROL The picture setting have been adjusted at the factory under optimum signal reception conditions. However, you can adjust for BRIGHTNESS, CONTRAST, COLOUR, SHARPNESS and TINT to your preference. Press the MENU button. MENU To adjust the BRIGHTNESS, press the SET UP or DOWN button, then press the ENTER button.
Page 20
PICTURE CONTROL To adjust the CONTRAST, press the SET UP or DOWN button, then press the ENTER button. Picture looks sharpest in the daytime by increasing the contrast. At night, the sharpest picture is obtained by reducing the contrast. ENTER CONTRAST To adjust the SHARPNESS, press the SET UP or DOWN button, then...
Page 22
TUNER LOCK Channel tuning once tuned in can be disable by selecting the tuner lock to "ON" by following steps 1-3. Press and hold the VOLUME UP button on the TV, and press the POWER button on the remote control simultaneously at the Stand By mode.
AV JACK CONNECTIONS AV JACK CONNECTIONS The exact arrangement you use to interconnect various video and audio components to the TV is dependent on the model and features of each component. Check the instruction book provided with each component for the location of video and audio inputs and outputs. The connection diagrams in the following are offered as suggestions.
Page 24
AV JACK CONNECTIONS 3. To connect the TV to an External Stereo Amplifier The AUDIO OUT JACK from the TV can be connected to a Stereo amplifier, which allows a higher quality sound (Monaural) when watching your favorite program. Rear of TV VIDEO AUDIO DC ( - - - - ) 12V...
TO WATCH NTSC VIDEO LASER DISC, DVD AND RECORDED VIDEO TAPE This TV has 4 COLOR SYSTEM (PAL, SECAM, NTSC 3.58/4.43) which allows you to watch Video Laser Disc and recorded video tapes. To watch NTSC Video Laser Disc, DVD and Recorded Video Tapes, appropriate equipment with NTSC playback must be used.
RECEPTION OF INTERFERENCE The most common types of television interference are as follows. IGNITION Black spots and horizontal streaks may appear, the picture may flutter or drift. This is usually caused by interference from car ignition system, neon lamps, electric drills or other electrical appliances.
TROUBLESHOOTING GUIDE In the event of problems, please check the following before seeking service. CHECKING ITEMS PRESET TV CHANNELS CHECK IF POWER PLUG IS FIRMLY CONNECTED TO THE POWER SUPPLY TRY A DIFFERENT CHANNEL. IF OK, THERE COULD BE A TRANSMISSION PROBLEM FROM THE TV STATION.
Weight and dimensions are approximate. Because we continually strive to improve our products we may change specifications and designs without prior notice. ACCESSORIES Remote Control Batteries (UM–4) Rod Antenna with Antenna Adapter DC 12V Car Cord ORION ELECTRIC CO., LTD. (JAPAN) 3G61401A '01/06 1 Piece 2 Pieces 1 Piece 1 Piece...