Table of Contents
Advertisement
Quick Links
BSL06T3FL &
BSL10T4FL
Installation Instructions
Firstlink Connected Emergency LED Drivers
! IMPORTANT SAFEGUARDS !
READ AND FOLLOW ALL SAFETY INSTRUCTIONS
1.
These products provide emergency lighting for a minimum of 90 minutes, in compliance with NFPA
101 and NEC 700.12.
2. Make sure all connections are in accordance with the National Electrical Code or Canadian
Electrical Code and any local regulations.
3. To reduce the risk of electric shock, disconnect both normal and emergency power supplies
before installation.
4. Install product in ambient temperatures and environments compliant with their ratings. These
products are suitable for use in damp locations. Products are not suitable for heated air outlets
and wet or hazardous locations.
5. An unswitched AC power source is required (120-277 VAC, 50/60 Hz).
6. Do not install near gas or electric heaters.
7.
Do not attempt to service the battery. A sealed, no-maintenance battery is used that is not field
replaceable. Contact the manufacturer for information on service.
8. The use of accessory equipment not recommended by the manufacturer may cause an unsafe
condition.
9. Do not use this product for other than intended use.
10. Installation should be performed by qualified service personnel.
11. Equipment should be mounted in locations and at heights where it will not be subjected to
tampering by unauthorized personnel.
12. These devices comply with part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) this device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
THIS PRODUCT CONTAINS A RECHARGEABLE LITHIUM-ION BATTERY.
SAVE THESE INSTRUCTIONS
THE BATTERY MUST BE RECYCLED OR DISPOSED OF PROPERLY.
Bodine © 2024 Signify Holding. All rights reserved.
Collierville, TN USA 38017 • Tech Support 888-263-4638 • www.bodine.com
WHEN USING ELECTRICAL EQUIPMENT, BASIC
SAFETY PRECAUTIONS SHOULD ALWAYS BE
FOLLOWED, INCLUDING THE FOLLOWING:
Li - ion
2/1/24
442296086571
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Bodine BSL06T3FL
Summary of Contents for Bodine BSL06T3FL
- Page 1 SAVE THESE INSTRUCTIONS Li - ion THIS PRODUCT CONTAINS A RECHARGEABLE LITHIUM-ION BATTERY. THE BATTERY MUST BE RECYCLED OR DISPOSED OF PROPERLY. 2/1/24 Bodine © 2024 Signify Holding. All rights reserved. Collierville, TN USA 38017 • Tech Support 888-263-4638 • www.bodine.com 442296086571...
- Page 2 EMERGENCY DRIVER INSTALLATION Make sure the necessary branch circuit wiring is available. An unswitched source of power is required. The emergency driver must be fed from the same branch circuit as the AC driver. Installation of this emergency LED driver will vary based on the luminaire type, however, generally follow these steps: STEP 1 - DETERMINE SUITABILITY...
- Page 3 STEP 3 - INSTALLING THE ILLUMINATED TEST SWITCH AND COMMUNICATION NODE Option 1: Using the Illuminated Test Switch/Communica- tion Node Bracket. > The illuminated test switch / communication node mounting bracket comes preassembled from the factory. The bracket can be mounted either through a 2”...
- Page 4 COMMUNICATION NODE WARNINGS • FirstLink communication node to be used only with FirstLink drivers, exit signs, and unit equipment. • Do not apply mains power directly to the node. • Do not cover the sensor during operation or mount the sensor internal to the luminaire. •...
- Page 5 WIRING DIAGRAM EMERGENCY DRIVER AND AC DRIVER MUST BE FED FROM THE SAME BRANCH CIRCUIT TYPICAL SCHEMATICS ONLY. MAY BE USED WITH OTHER DRIVERS. CONSULT THE FACTORY FOR OTHER WIRING DIAGRAMS. NOTE: Emergency driver case or green connector must be grounded NOTE 1: For short-term testing of the emergency function, the battery must be charged for at least one hour.
- Page 6 MAINTENANCE This self testing emergency driver automatically performs required routine testing. Results are reported to maintenance personnel via the indicator light. Note: Maintenance personnel should periodically check the indicator light. If the indicator light is flashing, follow steps in the Troubleshooting Guide. Self-Test: This unit contains a control/monitor circuit that if enabled automatically performs a 30-second discharge test once a month and a full 90-minute discharge test once a year.
- Page 7 (30 seconds every month) and duration tests (90 minutes every year) will be conducted automatically and the results stored in the unit awaiting download from the app. Test reports, in the form of Excel “.csv” files are available through the app as well. See Bodine FirstLink App Guide (FirstLink App...
Need help?
Do you have a question about the BSL06T3FL and is the answer not in the manual?
Questions and answers