Advertisement
Mounting
Trace holes A, B & C. Drill
Step 1
Plate
Holes along markings
A
A
C
C
B
B
DCCX
DCFX
**
Step 1
DCFX
Fix Duct Box Base Plate on
Installation Surface using
supplied screws & screw grips
A
B
A
Duct Box
Base Plate
B
Step 2
Fix Mounting Plate on Duct
Box Top Cover
DCFX
Connecting to Server
Connecting As Direct Door
Ethernet Switch
Assigning IP Address & Other Network Settings
Open a Web browser on your computer.
Ÿ
Enter the IP address of the PATH Controller (default: http://192.168.50.50) , in the
Ÿ
address bar of the browser and press the Enter key on your computer keyboard.
When prompted, enter the login credentials for the Door.
Ÿ
Default Username: Admin
Default Password: 1234
Click OK. On the Door Web page, select the Network tab and enter the required
Ÿ
network configuration such as Door IP address, Server IP address etc.
Save the Settings.
Ÿ
A
A
C
C
B
B
DCCX
DCFX
Fix Mounting Plate with supplied
Step 2
screw grips & screws
Duct Box
Step 3
Top Cover
Align on mounting plate
and slide downwards.
Mounting
Plate
DCFX
Connecting As Panel Door
RS-485
Application Server
Ethernet Switch
Up to 32
Installation Instructions - Concealed Wiring
Step 3
Connect cables and lead cables
through rectangular opening on the wall
Screw
Screw
grip
Hole
DCFX
Installation Instructions - Non-Concealed Wiring
DCCX
Cables
DCFX
Connect cables and lead cables
Step 4
through bottom opening of Duct Box
CAUTION
Do not install the device:
On unstable surfaces.
Ÿ
Where ferromagnetic field or noise is induced.
Ÿ
Where static is created, such as desks made of plastics, carpets.
Ÿ
Near volatile inflammable materials or inflammable goods such as drapes.
Ÿ
Where volatile gas and/or inflammable gas is created.
Ÿ
**
The duct box shown in the illustration is not a part of the product package and
must be purchased separately.
LED Status Indicators
Device Status
Power ON
Online
Up to 75
Offline
Degraded Mode
F i x M o u n t i n g
H o o k h e r e
DCFX
DCCX
Step 4
Align on mounting plate and
slide downwards.
Cables
DCCX
Step 5
Fix Top Cover to Base Plate by sliding Mounting Hook of top cover into the
Mounting Slot of base plate. Tighten screws at the bottom as shown.
This device complies with part15 of the FCC rules. Operation is subject to
the following two conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received, including
interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits of
Class A digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference when the equipment is operated in a commercial
environment.
This equipment generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instruction manual,
LED Indication
may cause harmful interference to radio communications. Operation of
Blue ON/OFF
this equipment in a residential area is likely to cause harmful interference
in which case the user will be required to correct the interference at his
Light Blue ON
own expense.
Red ON
Warning
This is a Class A product. In a domestic environment this product may
Orange ON
cause radio interference in which case the user may be required to take
adequate measures.
DCCX
When in place, tighten captive screw at bottom
DCCX
DCFX
FCC Compliance
Advertisement
