Advertisement
Quick Links
DESCRIPTION:
Series 5 are centrifugal magnetic drive
seal. All are serviceable with a screwdriver.
OPERATION:
Pumps are not self-priming, lack a suction lift, and thus require a flooded
suction. Pumps cannot be run dry because the impeller requires the liquid being pumped for
lubrication. For liquids with a specific gravity greater than water, have a higher viscosity, or for
elevated temperatures, a trimmed impeller may be necessary. For application assistance, contact
March Pump.
ELECTRICAL:
Models are dual voltage 115/230V for 60hz and 110/220V 50hz. The standard
motor has a conduit box. A motor with 115V 72 inch cord or 230V 72 inch cord, are options. The
motor is U.L. listed motor and rated for continuous duty. The pump is rated IP44. The pump is
Ignition Protected per SAE J1171 and ISO 8846.
CE:
Pumps marked with CE have been modified to be listed as CE. Contact March for more
information.
Specifications
TE-5M-MD Marked with CE
Product
1Ph
With 115V Cord
1 Ph
With 230V Cord
1 Ph
Inlet-Outlet
Max Internal Pressure
Max Liquid Temperature
Max Flow
Max Head
Model
GPM
LPM
FT
PSI
TE-5M-MD
18
68.1
29
12.6
TE-5MNS-MD
18
68.1
29
12.6
All specifications & data are based on pumping water & are intended as a guideline only. Specifications may vary with different motors.
pumps, eliminating the need for a shaft
TE-5MNS-MD Marked with CE
0150-0265-0100
0150-0268-0100
0150-0266-0100
0150-0269-0100
0150-0267-0100
0150-0270-0100
1"FPT-1/2"MPT
1"FPT-1/2"MPT
50PSI (344 kPa)
50PSI (344 kPa)
190F (87C)
190F (87C)
60Hz
Electrical
M
Ph
V
A
HP
8.85
1
115/230
2.6/1.3
1/5
8.85
1
115/230
2.6/1.3
1/5
TE-5M-MD and TE-5MNS-MD Marked with CE
Max Flow
Max Head
kW
RPM
GPM
LPM
Feet
PSI
0.149
3450
15.9
60.5
20.7 8.96
0.149
3450
15.9
60.5
20.7 8.96
50Hz
Electrical
M
Ph
V
A
HP
6.3
1
110/220
2.4/1.2
0.16
6.3
1
110/220
2.4/1.2
0.16
kW
RPM
0.119
2850
0.119
2850
0150-0275-1000
Advertisement
Related Manuals for March Pumps TE-5M-MD
Summary of Contents for March Pumps TE-5M-MD
- Page 1 TE-5M-MD and TE-5MNS-MD Marked with CE DESCRIPTION: Series 5 are centrifugal magnetic drive pumps, eliminating the need for a shaft seal. All are serviceable with a screwdriver. OPERATION: Pumps are not self-priming, lack a suction lift, and thus require a flooded suction.
- Page 2 TE-5MNS-MD: Polypropylene, Noryl, Buna N, 316 Stainless Steel, Carbon, Ceramic, Ceramic Magnet. LIMITED WARRANTY: March pumps are guaranteed only against defects in workmanship or materials for a period of one year from date of manufacture pumping water. For the complete warranty and to register online go to www.marchpump.com/warranty-registration For the General Installation Manual, see this link https://www.marchpump.com/wp-content/uploads/2019/07/march-pump-general-installation-guide-0750-040.pdf...
-
Page 3: Health Precautions
Safety Instructions & Preventive Maintenance Read this sheet and the appropriate pump instruction manual before installing and operating any pump. Failure to follow safety instructions may result in injury or death. Health Precautions These pumps utilize magnets. Any individuals with pacemakers, implanted defibrillators, electronic medical devices, metallic heart valves, or sickle cell anemia should consult a health care professional before working with these pumps. -
Page 4: Operation
Do not cover the motor. Check all electrical connections with the wiring diagram found on the motor. Most March Pumps are not self-priming pumps. Liquid must flow naturally to the pump. Do not operate the pump until liquid is inside of the pump. Never run the pump dry. -
Page 5: Shutdown Procedure
Assembly/Disassembly Magnets Magnets on specific models may be strong enough to pull the wet end and motor end quickly together during assembly or disassembly. WARNING: Do not put fingers between the two mating surfaces (between impeller magnet and/or impeller vanes and the rear pump housing) during assembly or disassembly, especially for the 7.5, 8, and 10 Series. -
Page 6: Draining The Pump
Draining the Pump 1. Wear appropriate safety gear. 2. Disconnect the power. 3. Close suction and discharge valves. 4. Remove pipe/hose/tube from suction and discharge. 5. Unscrew/untighten fasteners from wet end. 6. Direct outlet downward into appropriate container. NOTE: Observe local laws and regulations for handling and disposing hazardous liquids. Do not get motors wet. -
Page 7: Warranty
Vibration/Noise Motor not properly secured. • Piping not properly secured. • Pump cavitation from improper suction. • • Drive magnet rubbing against rear housing. Warranty Please see Warranty Page on March Website. www.marchpump.com/warranty-registration 0750-0984-1000 R3 (Revised 01/17/2024) - 5 -...