Related Manuals for Woods PFW2242S2
Summary of Contents for Woods PFW2242S2
- Page 1 PALLET FORK PFW2242S2 PFW4442S2 PFW4448S2 PF4448S2 PFW6648S2 MAN1354_2024-01.indd 1 MAN1354_2024-01.indd 1 1/24/24 12:37 PM 1/24/24 12:37 PM...
-
Page 2: Introduction
TO THE OWNER: Read this manual before operating your Woods equipment. The information presented will prepare you to do a better and safer job. Keep this manual handy for ready reference. Require all operators to read this manual carefully and become acquainted with all adjustment and operating procedures before attempting to operate. -
Page 3: Table Of Contents
TABLE OF CONTENTS INTRODUCTION..........2 SPECIFICATIONS . -
Page 4: Specifications
SPECIFICATIONS MODELS SPECIFICATION PFW2242S2 PFW4442S2 PFW4448S2 PF4448S2 PFW6648S2 Weight (lbs) Fork Spread Maximum width 46.75 inches (six inch increments) Back Grade Tooth Double Lock Downs Maximum Carry Load (in lbs) 2200 4400 4400 4400 6600 at 19.7" load center of forks Fork Cross Section 1.2 x 3.2... -
Page 5: Safety 5
SAFETY RULES ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED! ■ Air in hydraulic systems can cause erratic opera- Safety is a primary concern in the design and man- tion and allows loads or equipment components ufacture of our products. Unfortunately, our efforts to drop unexpectedly. -
Page 6: Maintenance
SAFETY RULES ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED! ■ Do not put Pallet Fork into service without ■ Stop power unit and implement immediately forks properly engaged on frame rails and fork upon striking an obstruction. Dismount power lockplate secured in place. Fork locks must unit, using proper procedure. -
Page 7: Storage
SAFETY RULES ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED! STORAGE ■ Always wear relatively tight and belted clothing to avoid getting caught in moving parts. Wear sturdy, rough-soled work shoes and protec- ■ Block equipment securely for storage. tive equipment for eyes, hair, hands, hearing, ■... -
Page 8: Safety & Instructional Decals
Replacement safety decals can be ordered free from your Woods dealer. To locate your nearest dealer, check the Dealer Locator at www.WoodsEquipment.com, or in the United States and Canada call 1-800-319-6637. - Page 9 Loader n Skid steer must MAXIMUM Operator's Manual have ROP� S and seat before operating. CARRY LOAD: belt / operator (Woods manuals restraint. Keep seat are available 4400 lbs. belt / operator from dealer or call restraint securely 1-800-319-6637.) fastened.
-
Page 10: 10 Operation
OPERATION The operator is responsible for the safe operation of ATTACHING PALLET FORK TO LOADER the equipment. The operator must be properly trained. Operators should be familiar with this equipment, the tractor, and all safety practices before starting opera- WARNING tion. -
Page 11: Operating Loader
Shut off the engine, set brake, remove key, remove ■ Never use attachment to carry loads that exceed the rated operating capacity or other specifica- seat belt, and release operator restraint. Dismount the loader. tions of the power unit. Check your power unit manual or see your dealer for rated operating Move the loader coupler handles to the locked position. -
Page 12: Lock Lever
STORAGE Lock Lever Released WARNING ■ Block equipment securely for storage. CAUTION ■ Keep children, bystanders, and animals away Fork from the equipment and the storage area Inspect the Pallet Fork thoroughly and prepare for stor- CM1165 age. Repair or replace any damaged components. Figure 5. -
Page 13: Owner Service 13
OWNER SERVICE The information in this section is written for operators CAUTION who possess basic mechanical skills. If you need help, your dealer has trained service technicians available. For your protection, read and follow the safety informa- ■ If you do not understand any part of this manual tion in this manual. -
Page 14: Fork Installation
FORK INSTALLATION CLEANING After Each Use WARNING ■ Remove large debris such as clumps of dirt, ■ Fork Tines are heavy and can cause muscle grass, crop residue, etc. from machine. strain or back injury. Use lifting aids and proper ■... -
Page 15: Assembly 15
ASSEMBLY DEALER SET-UP INSTRUCTIONS Assembly of this equipment is the responsibility of the UPPER RAIL Woods dealer. It should be delivered to the owner com- LOCK NOTCHES pletely assembled, lubricated, and adjusted for normal operating conditions. Complete checklists on page 16 when you have com- pleted the assembly. -
Page 16: 16 Dealer Checklists
DEALER CHECKLISTS DEALER PRE-DELIVERY CHECKLIST DELIVERY CHECKLIST (DEALER’S RESPONSIBILITY) (DEALER’S RESPONSIBILITY) Inspect the equipment thoroughly after assembly to Show customer how to make adjustments. ensure it is set up properly before delivering it to the Instruct customer how to lubricate and explain customer. -
Page 17: Parts 17
PFW SERIES 2 PALLET FORK PARTS LIST MODELS - PFW2242S2, PFW4442S2, PFW4448S2, PF4448S2, PFW6648S2 CD9349 PART DESCRIPTION USED ON PALLET FORK FRAME 602497RP FORK TINE, 1.2 X 3.2 X 42 PFW2242S2 602509RP FORK TINE, 1.4 X 3.9 X 42 PFW4442S2 602510RP FORK TINE, 1.4 X 3.9 X 48... - Page 18 NOTES 18 Parts MAN1354 ( 01/24/2024 ) MAN1354_2024-01.indd 18 MAN1354_2024-01.indd 18 1/24/24 12:37 PM 1/24/24 12:37 PM...
-
Page 19: Appendix 19
BOLT TORQUE CHART Always tighten hardware to these values unless a different torque value or tightening procedure is listed for a specific application. Fasteners must always be replaced with the same grade as specified in the manual parts list. Always use the proper tool for tightening hardware: SAE for SAE hardware and Metric for metric hardware. Make sure fastener threads are clean and you start thread engagement properly. -
Page 20: Bolt Size Chart & Abbreviations
BOLT SIZE CHART NOTICE: Chart shows bolt thread sizes and corresponding head (wrench) sizes for standard SAE and metric bolts. SAE BOLT THREAD SIZES 5/16 10mm 12mm 14mm 16mm 18mm METRIC BOLT THREAD SIZES ABBREVIATIONS AG ....Agriculture HT . -
Page 21: Index 21
INDEX ASSEMBLY OWNER SERVICE Dealer Set-Up Instructions 15 Cleaning After Each Use 14 DEALER CHECKLISTS Periodically or Before Extended Storage 14 Delivery (Dealer’s Responsibility) 16 Daily Service 13 Pre-Delivery (Dealer’s Responsibility) 16 Fork Installation 14 GENERAL Fork Removal 13 Abbreviations 20 PARTS Bolt Size Chart 20 Parts List 17... - Page 22 Woods logo are trademarks of Woods Equipment Company. All other ® trademarks, trade names, or service marks not owned by Woods Equipment Company that appear in this manual are the property of their respec tive companies or mark holders. Specifications subject to change without notice.