Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Hiniker 600P
Summary of Contents for Hiniker 600P
- Page 1 POLY RECEIVER HITCH SPREADER MODEL: 600P & 1000P OPERATOR’S MANUAL DO NOT USE OR OPERATE THIS EQUIPMENT UNTIL THIS MANUAL HAS BEEN READ AND THOROUGHLY UNDERSTOOD Please visit www.snowplows.hiniker.com to access the most recent version PART NUMBER 25014940...
-
Page 3: Table Of Contents
Table of Contents TABLE OF CONTENTS 25014940 10/23 Hiniker/25014940 TO THE PURCHASER ........................2 SAFETY ............................3-4 OPERATING PROCEDURES ....................5-9 General Information........................ 5 Sander Control Box ........................ 5 Spread Control ........................7 Transporting Spreader ......................7 Spreader Optional Equipment ....................7 Swing Away Kit ........................ -
Page 4: To The Purchaser
Check that your dealer has forwarded the Hiniker delivery report copy and the machine serial number to maintain maximum service and warranty benefits. This does not put you on any mailing list and information thereon is not... -
Page 5: Safety
Replace these with genuine GENERAL SAFETY Hiniker parts. Read this manual thoroughly. Make sure Check all controls and operating functions the operator understands it and knows of machine in a safe area before starting to how to operate this equipment safely. - Page 6 Safety DURING OPERATION Drive carefully and always wear seat belts when operating a motor vehicle. Braking distance may be increased and handling characteristics impaired due to extra weight of spreader. Ensure everyone is clear of machine, especially away from blind areas of the operator, before starting or operating this equipment.
-
Page 7: Operating Procedures
GENERAL INFORMATION Calculate total material weight by multiplying pounds per cubic foot by cubic foot of material. Hiniker spreaders are capable of dispersing Always examine spreader for worn or damaged a variety of dry materials for control of ice on components prior to operation. - Page 8 When blast button is held down material feed drive system runs at full The Hiniker controller will pulse the drive motor power applying maximum amount of material. on and off a few times then drive motor at full Light beside “Blast”...
-
Page 9: Spread Control
Hiniker spreaders are equipped with a bottom the spreader (as shown). hopper slide gate to make checking material jams easier. -
Page 10: Swing Away Kit
8 Operating Procedures SWING AWAY KIT (Optional) Hiniker Swing Away Kit makes loading of pallets of bagged material into the back of a vehicle easier. The swing away option can only be used when the hopper is completely empty. DWG NO. 7272... -
Page 11: Storage
Operating Procedures 9 STORAGE Store spreader in a cool dry protected area when it will not be used for an extended period of time. Never attempt to remove spreader with material in hopper. Perform these maintenance procedures at end of season to ensure machine remains in good operating condition: Unload hopper completely and wash to flush out any remaining material to prevent... -
Page 12: Maintenance & Service Procedures
10 Maintenance & Service Procedures MAINTENANCE & SERVICE PROCEDURES Dependable spreader operation is a result Apply a light coat of dielectric grease to all of following good maintenance procedures. electrical connectors to prevent corrosion of Inspect your spreader frequently to ensure that contacts when connectors are unplugged, and all parts are working smoothly, and develop a to make connecting and disconnecting plugs... -
Page 13: Trouble Shooting
Trouble Shooting TROUBLE SHOOTING Preliminary Checks: – Be sure all electrical connections are tight and clean. – Be sure nothing is jammed in hopper or spinner. PROBLEM POSSIBLE CAUSE REMEDY No power to cab Controller plug is loose Check plug connection at cab Power switched to ON position control No illumination of indicator light... -
Page 14: Installation Instructions
Remove spreader from shipping container. Remove zip tie securing grid to hopper. Carefully remove grid from hopper to access parts box. Remove Hiniker controller, wiring harness, ratchet straps, etc from parts box. Verify everything has been removed from inside the hopper. - Page 15 Installation Instructions Attach mating connectors between wiring harness and cab controller. CAUTION: Make sure power switch on controller is off before connecting power cable. Lay out a path for power cable in truck’s engine compartment. Drill a hole in firewall or use an existing one to pass wiring harness.
- Page 16 Installation Instructions DWG. NO. 7295...
-
Page 17: Specifications
Specifications SPECIFICATIONS DIMENSIONS: 600P HOPPER 1000P HOPPER Overall Length 25 Inches 29 1/2 Inches Overall Width 32 Inches 38 1/4 Inches Overall Height 36 1/2Inches 39 Inches Hopper Length 24 Inches 28 Inches Hopper Width 30 Inches 35 1/2 Inches... - Page 18 16 Notes NOTES:...
-
Page 19: Warranty
INCIDENTAL, INDIRECT OR CONSEQUENTIAL DAMAGE OR DAMAGES OF ANY KIND FOR LOST PROFITS OR DELAY. If requested by Hiniker, products or parts for which a warranty claim is made are to be returned freight prepaid to our factory. Any improper use, operation beyond rated capacity, substitution of parts not approved by Hiniker Company, or any alteration or repair in such manner as in our judgment affects the product materially and adversely shall void this warranty.
Need help?
Do you have a question about the 600P and is the answer not in the manual?
Questions and answers