Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for AES IntelliPro Fire 7794
Summary of Contents for AES IntelliPro Fire 7794
- Page 1 AES 7794 IntelliPro Fire Installation Manual AES Corporation 285 Newbury Street Peabody, MA 01960-1315 USA Tel (978) 535-7310 • Fax (978) 535-7313 P/N 40-7794 Rev 5 www.aes-intellinet.com Jun 9, 2015 Copyright 2014 All Rights Reserved ;sdkpfo pijfpfpodkspfosd...
- Page 2 AES 7794 IntelliPro Fire – Installation Manual THIS PAGE INTENTIONALLY LEFT BLANK AES Corporation 40-7794, Rev 5, 6/9/2015...
-
Page 3: Table Of Contents
AES 7794 IntelliPro Fire – Installation Manual TABLE OF CONTENTS Summary ........................6 Basic Functions....................6 User Interface ....................6 System Requirements ..................6 1.3.1 Fire Alarm Control Panel Telco Interface Requirements ....... 6 Safety Considerations ..................7 Technical Specifications ................... 7 Installation of 7794 in subscriber unit .............. - Page 4 AES 7794 IntelliPro Fire – Installation Manual 5.6.15 CID 4xx Letter ..................23 5.6.16 M3 EC TEXT to CID Enabled..............24 5.6.17 Voltage Pump Enabled ................24 5.6.18 Clock FShift Enabled ................24 Configuration options – Supplemental Communication ......24 5.7.1 Phone Line ....................
- Page 5 AES 7794 IntelliPro Fire – Installation Manual 11.2 Parts List ......................35 11.3 Contact Information ..................35 12 Revision History ...................... 35 13 Warranty and Service Procedure ................36 AES Corporation 40-7794, Rev 5, 6/9/2015...
-
Page 6: Summary
1.3 System Requirements This document assumes the user knows how to set the AES subscriber unit account number, cipher and other configuration settings as well as how to operate the AES Multi Net software environment including IPCtrl and automation. 1.3.1 Fire Alarm Control Panel Telco Interface Requirements NOTE: ... -
Page 7: Safety Considerations
NFPA 70, National Fire Code NFPA 72 and local building codes. Test this system periodically for proper operation. AES assumes no responsibility for this equipment's failure to operate. AES' sole responsibility is to repair or replace any AES device found to be defective during the warranty period. -
Page 8: Installation Of 7794 In Subscriber Unit
AES 7794 IntelliPro Fire – Installation Manual 2 Installation of 7794 in subscriber unit Remove four (4) of the hex nuts shown in Figure 2 that hold the subscriber unit board in the subscriber enclosure. Save the hex nuts. -
Page 9: Primary Communication Interface
AES 7794 IntelliPro Fire – Installation Manual Mount the 7794 PC board on four newly installed standoffs. Install insulating washer (P/N 09-7X94) over mounting hold H3. Temporarily secure the board using the 4 hex nuts removed earlier Important: Place the Earth Ground hex nut (green) on the right side center hex standoff as shown in Figure 2 above. -
Page 10: Connecting 7794 To Alarm Panel - Primary Communication Interface
Figure 5 and Figure 5A below. The 7794 is supervised by the 7762 using a ‘heartbeat’. See the 7762 Install Manual AES P/N 40-7762 for detail. NOTE: The 7794 IntelliPro and subscriber must be connected to the FACP within the same room and in no more than 20 ft. -
Page 11: Connection Details - Primary Communication Interface
AES 7794 IntelliPro Fire – Installation Manual Figure 5A. 3.3 Connection Details – Primary Communication Interface When mounted in a subscriber enclosure and connected to the Fire Alarm Control Panel dialer, the 7794 delivers alarm messages to the central monitoring station as shown in Figure 5 and Figure 5A above. - Page 12 AES 7794 IntelliPro Fire – Installation Manual b) Connect FACP Dialer 1 and Dialer 2 TIP wire to J6 terminal block labeled AP TIP. c) Connect FACP Dialer 1 and Dialer 2 RING wire to the J6 terminal block labeled AP RING.
-
Page 13: Supplemental Communication Interface
AES 7794 IntelliPro Fire – Installation Manual 4 Supplemental Communication Interface 4.1 Connector and LED Locations Trouble output RJ11 connection to AES (Form C relay) RJ11 subscriber connection to Handheld RJ31 TO AP Pots, AP, CPE interfaces (see detail) RJ31 FROM... -
Page 14: 7794 To Alarm Panel - Us Installation - Supplemental Communication Interface
AES 7794 IntelliPro Fire – Installation Manual 4.2 7794 to Alarm Panel - US Installation - Supplemental Communication Interface Figure 6B. FACP (Fire Alarm Control Panel) with both dialers connected to the 7794 (AP TIP and AP RING) as shown in Figure 6B. -
Page 15: Connection Details -7794 To Alarm Panel - Us Installation
AES 7794 IntelliPro Fire – Installation Manual 4.2.1 Connection Details –7794 to Alarm Panel - US Installation 1) Connect the FACP Dialer 1 and Dialer 2 TIP and RING to the 7794 terminal block labeled AP TIP RING as shown in Figure 6C below. -
Page 16: Connect 7794 To Alarm Panel - Canada/Dual Dialer Installation - Supplemental Communication Interface
AES 7794 IntelliPro Fire – Installation Manual 4.3 Connect 7794 to Alarm Panel – Canada/Dual Dialer Installation - Supplemental Communication Interface Figure 6D. FACP with PSTN and RF Method 1: PSTN via Dialer 1 Method 2: RF (7788F-C #1) via Relays... -
Page 17: Connection Details - 7794 To Alarm Panel - Canada Installation
Telco connection. 5 Configure 7794 The 7794 is configured using the AES Hand Held programmer (P/N 7041E) and programmer cable (P/N 13-0395). Perform the following: 5.1 Connecting the Handheld Programmer The 7794 must be installed and connected by the interconnect cable to the subscriber unit as described in Section 3. -
Page 18: Configuration Interface
Some Hand Held programmers have a slow response time.) 5.3 Configuration Interface The 7794 can be configured using the Hand Held programmer, a PC configured as a terminal, or using the AES IntelliLoader (Note: Check the IntelliLoader version for features that can be programmed.) 5.4 Entering Configuration Mode It is a good practice to configure the 7794 with the FACP disconnected. -
Page 19: Phone Line
AES 7794 IntelliPro Fire – Installation Manual Configuration Available settings Required settings options Line cut Report Not Used. Not Used. POTS cut report delay Not Used. Not Used. POTS restoral delay Not Used. Not Used. AP ACCT override Select based on account ID requirement. -
Page 20: Cid Alarm Format
AES 7794 IntelliPro Fire – Installation Manual Pulse formats at 10 and 20 pulses per second, with combinations of handshake, kiss-off, and center pulse frequencies, plus variable durations that cover most pulse formats Modem formats from Bosch, ranging from Modem II to Modem IIIa. -
Page 21: Ap Input Gain
AES 7794 IntelliPro Fire – Installation Manual Options are A=1.4,B=2.3 C=CF (Center frequency) (default 1.8 KHz) Options are A=1.8,B=1.9 I=IDT (Inter digit time) (default 0.7 sec) Options are A=0.7,B=0.9,C=1.7 R=IRT (Inter round time) (default 0.8 sec) Options are A=3.0,B=5.0 5.6.4 AP Input gain The AP input gain increases the 7794 sensitivity when listening to the FCAP. -
Page 22: Pots Cut Report Delay
The purpose of this option is to allow bypassing the alarm panel account. When set to YES, the account number of the AES subscriber is used in place of the account number in the control panel. This is a useful feature for automation software packages that do not allow two distinct account numbers in one customer account. -
Page 23: Ap Output Gain
AES 7794 IntelliPro Fire – Installation Manual YES to enable. NO to disable. (DEFAULT) This must be set to YES to allow viewing of advanced configuration options. Use: F3:Change setting F4:Go UP to prior screen F5:Do DOWN to next screen 5.6.12 AP Output Gain... -
Page 24: M3 Ec Text To Cid Enabled
AES 7794 IntelliPro Fire – Installation Manual 5.6.16 M3 EC TEXT to CID Enabled Options are: YES: enable (DEFAULT) NO: disable Use: F3:Change setting F4:Go UP to prior screen F5:Do DOWN to next screen 5.6.17 Voltage Pump Enabled Options are:... -
Page 25: Phone Line
AES 7794 IntelliPro Fire – Installation Manual Configuration options Available settings AP Input gain 10/20 Intercept blind dial Line cut Report POTS cut report delay Any value between 0-9999(seconds) POTS restoral delay Any value between 0-9999(seconds) AP ACCT override POTS Input gain... -
Page 26: Cid Alarm Format
AES 7794 IntelliPro Fire – Installation Manual The options for the alarm panel report are CID, MODEM or PULSE with: C=CID, M=MODEM, P=PULSE Press F3 to change the value. Use: F4:Go UP to prior screen F5:Do DOWN to next screen 5.7.3.1 CID Alarm Format... -
Page 27: Ap Input Gain
AES 7794 IntelliPro Fire – Installation Manual Options are A=0.7,B=0.9,C=1.7 R=IRT (Inter round time) (default 0.8 sec) Options are A=3.0,B=5.0 5.7.4 AP Input gain The AP input gain increases the 7794 sensitivity when listening to the FCAP. Some panels will adjust to this setting. -
Page 28: Pots Cut Report Delay
The purpose of this option is to allow bypassing the alarm panel account. When set to YES, the account number of the AES subscriber is used in place of the account number in the control panel. This is a useful feature for automation software packages that do not allow two distinct account numbers in one customer account. -
Page 29: Ap Output Gain
AES 7794 IntelliPro Fire – Installation Manual NO to disable. (DEFAULT) This must be set to YES to allow viewing of advanced configuration options. Use: F3:Change setting F4:Go UP to prior screen F5:Do DOWN to next screen 5.7.12 AP Output Gain AP output gain sets the output gain when the 7794 is in POTS mode (POTS=NO). -
Page 30: Voltage Pump Enabled
1 pulse per second Normal operation Fast blink 2 pulses per second 7794 cannot communicate with the subscriber No blink, always on 7794 not operating properly and should be returned to AES for repair AES Corporation 40-7794, Rev 5, 6/9/2015... -
Page 31: Format: Contact Id
AES 7794 IntelliPro Fire – Installation Manual 7 Format: Contact ID The 7794 is fully compliant with the Contact ID (CID) protocol. Select option “C”. For details on how to configure the 7794 to process CID, see Section 5.6.3.1 – CID Alarm Format on Page 20. -
Page 32: Bosch/Radionics Panels Supported
AES 7794 IntelliPro Fire – Installation Manual This sub menu is only available if the report format is MODEM and the format is MODEM2, and an “unknown panel type” has been detected. The default family type displayed on this sub-menu is NONE. -
Page 33: Settings For Non-Supported Formats
AES 7794 IntelliPro Fire – Installation Manual Pulse Format Ademco HS Double Round (3+1 Expanded) Ademco Slow Silent Knight Slow, HS 1400 Hz Ademco Slow Silent Knight Slow, HS 2300 Hz Radionics Fast (20pps) (4+2) Radionics Fast (20pps) (4+1) Radionics Fast (20pps) (3+1) -
Page 34: Double Round
AES 7794 IntelliPro Fire – Installation Manual 9.3.2 Double round Double round sends the same message twice and is automatically detected. This is a method used by some pulse protocols to allow a receiver, the 7794 in this case, to validate the data received. -
Page 35: Maintenance, Warranty And Repair
11.2 Parts List The 7794 IntelliPro includes the following items: o 7794 IntelliPro o AES RJ11 cable P/N 13-0395 o Hex standoffs, (1 1/4 in.) AES P/N 09-2015 11.3 Contact Information AES Corporation 285 Newbury Street Peabody, Massachusetts 01960 USA Website: http://www.aes-intellinet.com... - Page 36 AES including central station receivers and accessories will be warranted for one (1) year from the date of purchase. At no cost to the original purchaser for parts or labor, AES will repair or replace any AES Product or any, part or parts thereof which are judged defective under the terms of this Warranty.
Need help?
Do you have a question about the IntelliPro Fire 7794 and is the answer not in the manual?
Questions and answers