Related Manuals for Fema I4 Series
Summary of Contents for Fema I4 Series
- Page 1 USER’S MANUAL SERIES I4 · Model I4F ISOLATED SIGNAL CONVERTER Section INDUSTRIAL www.fema.es INDUSTRIAL Impulses Frequency Flow 5799r00...
-
Page 2: Table Of Contents
16.6 Display information 16.7 Key ‘UP’ (‘force’ menu) 16.8 Key ‘LE’ (‘messages’ function) User’s Manual www.fema.es/docs/5799_I4F_manual_en.pdf 16.9 ‘Tools’ menu Datasheet www.fema.es/docs/5801_I4F_datasheet_en.pdf 17. Full configuration menu....16 18. -
Page 3: Installation And Start-Up
(eventually this access can be password locked) in order to deactivate the ‘SOS mode’. Deactivation of ‘SOS mode’ must be performed manually by configuring the function to ‘oFF’. To configure the ‘SOS mode’ function, see section 16.9. w w w. fema . es... -
Page 4: Predefined Configuration Codes
‘uSEr’. • Code ‘---’ identifies the end of the list, it follows code ‘199’ and the list continues with code ‘010’. Select ‘---’ exits the ‘configuration menu’ without applying changes. FEMA · MANUFACTURING FOR INDUSTRIAL AUTOMATION... -
Page 5: Connections And Dimensions (Mm (Inch))
Others common signal Vexc common +Vdc 0/10 Vdc common +Vdc Terminal 4 and terminal 1 are internally connected. Connecting dangerous voltages to terminal 4 makes terminal 1 a terminal with dangerous voltage. 7 8 9 w w w. fema . es... -
Page 6: How To Operate The Instrument
‘On ‘Sq’’ parameter (see section 16.9). When the operator exits the ‘configuration menu’, the output Flashing signal is temporarily set to minimum value for a time <5 seconds, while the instrument restarts. FEMA · MANUFACTURING FOR INDUSTRIAL AUTOMATION... -
Page 7: How To Operate The 'Force' Menu
‘force’ menu, the messages associated to the ‘LE’ (3) key, activate filters, password function, etc. See section 16 for a detailed explanation on the ‘configuration menu’. w w w. fema . es... -
Page 8: Input Signals
1 2 3 1 2 3 Terminal 4 and terminal 1 are internally connected. Connecting dangerous voltages to terminal 4 makes terminal 1 a terminal with dangerous voltage. +8.2 Vexc signal signal common NAMUR Pick-up FEMA · MANUFACTURING FOR INDUSTRIAL AUTOMATION... -
Page 9: Technical Specifications
(see section 16.2). Parameters not available in the active mode, will Namur 5.1 KOhms ±30 Vdc show ‘-nA-’ when accessing their value at the configuration menu. 5.1 KOhms ±30 Vdc ‘0’ level <1V, ‘1’ level >2V <600 Vac 900 KOhms 800 Vac <60 Vac 340 KOhms 200 Vac w w w. fema . es... -
Page 10: Configuration Menu
. Gain applies only to signals through channel ‘A’ and connected 5 Vdc to terminals ‘123’. disabled • select ‘G__1’ to activate the gain ‘1’. Usual gain for Vdc signals, that are correctly detected operating the ‘trigger level’. FEMA · MANUFACTURING FOR INDUSTRIAL AUTOMATION... -
Page 11: Input Range
‘Advanced scaling’ (Ad.Sc) parameters (see section 16.5). 0/600 Hz • example: select the ‘1 KHz ’ input range and to customize to a smaller 0/800 Hz range (for example 0/750 Hz or 250/750 Hz) see section 16.5 and operate each parameter. 0/1 KHz w w w. fema . es... -
Page 12: Output Range
‘Process low’ (Pr.Lo) parameter, configure the process value associated to the low input signal value. • at the ‘Process high’ (Pr.hI) parameter, configure the process value associated to the high input signal value. FEMA · MANUFACTURING FOR INDUSTRIAL AUTOMATION... -
Page 13: Display Information
‘0’ is the value assigned to the ‘input signal low’ parameter, and ‘100’ is the value assigned to the ‘input signal high’ parameter (see section 16.5) (for example : ‘Prct 23.5’ when the reading is 23.5% of the full scale). w w w. fema . es... -
Page 14: Key 'Up' ('Force' Menu)
Select the value from 0 to 100% of the active output range (4/20 mA or 0/10 Vdc). To deactivate the ‘SOS mode’ select ‘oFF’. See section 6 for more information on the ‘SOS mode’. FEMA · MANUFACTURING FOR INDUSTRIAL AUTOMATION... - Page 15 ‘configuration menu’. The password does not block access to the ‘force’ menu. To deactivate the password, select ‘oFF’. • at the ‘Factory reset’ (FAct) parameter select ‘yes’ to activate the default factory configuration (see section 18 for a list of factory default parameters). w w w. fema . es...
-
Page 16: Full Configuration Menu
0/80 Hz minimum level 0/100 Hz 0/200 Hz Antirrebound filter 0 to 1000 m Seconds 0/400 Hz 15 Vdc 0/600 Hz Excitation voltage 8.2 Vdc for Namur 0/800 Hz 5 Vdc 0/1 KHz disabled 0/2 KHz 0/4 KHz channel ‘A’ 0/6 KHz Reading channel channel ‘B’ 0/8 KHz FEMA · MANUFACTURING FOR INDUSTRIAL AUTOMATION... - Page 17 Display output signal value information label Average filter 0 to 100 process value signal percentage ‘Dead band’ 0.0 to 100.0% Version Key ‘UP’ Force low (‘force’ menu) Password Force high Factory reset Force set w w w. fema . es...
-
Page 18: Factory Default Parameters
• the leds light a round shape while the new configuration is applied • the start up message appears (‘SEnSor nPn 1.000 kHz’) • the actual signal input value is displayed • the instrument is in ‘normal mode’ of operation FEMA · MANUFACTURING FOR INDUSTRIAL AUTOMATION... -
Page 19: Precautions On Installation
Within the warranty period and after examination by the manufacturer, the unit will be repaired or substituted when found to be defective. Extended warranty available at (see section 3) w w w. fema . es...