Related Manuals for Fema I4 Series
Summary of Contents for Fema I4 Series
- Page 1 USER’S MANUAL SERIES I4 · Model I4P ISOLATED SIGNAL CONVERTER Section INDUSTRIAL www.fema.es INDUSTRIAL Temperature Temperature Temperature Resistances Process Potentiometer 5488r02...
- Page 2 13.7 Display information 13.8 Key ‘UP’ (‘force’ menu) 13.9 Key ‘LE’ (‘messages’ function) User’s Manual www.fema.es/docs/5488_I4P_manual_en.pdf 13.10 ‘Tools’ menu Datasheet www.fema.es/docs/5486_I4P_datasheet_en.pdf 14. Full configuration menu....22 15.
-
Page 3: Installation And Start-Up
(eventually this access can be password locked) in order to deactivate the ‘SOS mode’. Deactivation of ‘SOS mode’ must be performed manually by configuring the function to ‘oFF’. To configure the ‘SOS mode’ function, see section 13.10. w w w. fema . es... - Page 4 • Code ‘----’ identifies the end of the list, it follows code ‘199’ and the list Reserved 048 to 049 148 to 149 continues with code ‘010’. Select ‘----’ to exit the list without applying changes. FEMA · MANUFACTURING FOR INDUSTRIAL AUTOMATION...
- Page 5 11.6 (2 wires) terminal 1 Pt500, Pt1000 11.6 common Resistances res- res+ 11.3 +Vdc 0/10 Vdc common +Vdc pot+ Potentiometer pot- signal 11.2 (+5 Vexc) Passive Vexc 7 8 9 common signal 11.2 potentiometer (in) w w w. fema . es...
-
Page 6: 'Normal Mode' Of Operation
‘On SQ’ parameter (see section 13.10). Table 6 ‘ECO’ DECIMAL POINT When the operator exits the ‘configuration menu’, the output signal is temporarily set to minimum value for a time Flashing <5 seconds, while the instrument restarts. FEMA · MANUFACTURING FOR INDUSTRIAL AUTOMATION... - Page 7 To exit the ‘force’ menu, press the ‘LE’ (3) key, or press the key ‘UP’ (5) key until the parameter ‘----’ appears, and select by pressing the ‘SQ’ (<) key, or wait without pressing any key until the automatic ‘rollback’ activates. w w w. fema . es...
- Page 8 Code for Code for Accuracy Max. overvoltage on range 4/20 m A output 0/10 V dc output (% F S) passive Vexc 0/10 Vdc <0.10% 50 Vdc 1 MOhm 0/100 % <0.20 % 20 Vdc Voltage drop on terminals <2 Vdc. FEMA · MANUFACTURING FOR INDUSTRIAL AUTOMATION...
- Page 9 -80/75 ºC -112/167 º F <0.10 % 0/100 K Ohm <0.20 % 4.5 uA 3 Vdc Ntc 44034 -80/75 ºC -112/167 º F <0.10 % β 0/1000 K Ohm <0.50 % 1 uA 3 Vdc Ntc R =10K, =3500 -50/90 ºC -58/194 º F <0.20 % w w w. fema . es...
- Page 10 0/250 º C 32/482 º F <0.40% F S ±2º C Thermoc. 250/1820 º C 482/3308 º F <0.40% F S ±2º C 0/150 º C 32/302 º F <0.70% F S ±2º C FEMA · MANUFACTURING FOR INDUSTRIAL AUTOMATION...
- Page 11 1 2 3 1 2 3 Pt100+ Pt100+ Pt100- (3 wire) Pt100- Pt100- (shortcircuit 1-2) Connections for Pt100 (3 wires) Connections for Pt100 (2 wires) 1 2 3 Connections for Pt500 and Pt1000 (2 wires only) w w w. fema . es...
- Page 12 FEMA · MANUFACTURING FOR INDUSTRIAL AUTOMATION...
-
Page 13: Technical Specifications
(pitch 5.08 mm) input - output 3000 Veff (60 seconds) housing material polyamide V0 power - input 3000 Veff (60 seconds) weight <150 grams power - output 3000 Veff (60 seconds) packaging 120 x 115 x 30 mm, cardboard w w w. fema . es... -
Page 14: Input Range
At the ‘Potentiometer’ (Pot) parameter select to activate the Ntc 44007 potentiometer mode. At the ‘Passive Potentiometer’ (Pot.P) parameter select to activate Ntc 44008 the passive potentiometer mode. See section for an explanation of 11.2 differences between potentiometer and passive potentiometer measure. FEMA · MANUFACTURING FOR INDUSTRIAL AUTOMATION... -
Page 15: Output Range
At the ‘Output range’ (out) menu entry, select the output signal range to 4/20 mA (value ‘420’) or to 0/10 Vdc (value ‘010’). Output range The output signal range selected can be later customized to operate in a reduced range of signal (see section 13.6). w w w. fema . es... -
Page 16: Temperature Configuration
Apply the ‘field correction low’ function to force the output to be 4.00 mA at the actual input signal detected (4.05 mA). FEMA · MANUFACTURING FOR INDUSTRIAL AUTOMATION... - Page 17 (see section 13.7) or the ‘messages’ function (see section 13.9). Process parameters are not available for temperature ranges. • at the ‘Process low’ (Pr.Lo) parameter, configure the process value associated to the low input signal value. w w w. fema . es...
-
Page 18: Display Information
‘Force Set’ (F.SEt) to ‘on’ to activate the ‘Force set’ function menu entry. The functions configured to ‘on’ are available at the ‘force’ menu. See section 10.4 for a description on each function and how to operate them. FEMA · MANUFACTURING FOR INDUSTRIAL AUTOMATION... -
Page 19: Tools Menu
• select ‘Standard output’ (Stdr) to overrange output signal to maximum value in case of input signal overrange, and to underrange output signal to minimum value in case of input signal underrange. w w w. fema . es... - Page 20 ‘force’ menu. To deactivate the password, set the password value to ‘0000’. • at the ‘Factory reset’ (FAct) parameter select ‘yes’ to activate the default factory configuration (see section 15 for a list of factory default parameters). FEMA · MANUFACTURING FOR INDUSTRIAL AUTOMATION...
- Page 21 SERIES I4 · Model I4P S ec t i on I N DU S T R I A L . I S O L AT E D S I G N AL C ON VERT ER S w w w. fema . es...
- Page 22 Ntc 44030 Ntc 44031 Ntc 44032 The ‘ok’ message flashes Ntc 44033 while the ‘field correction’ Process Field correction function is being applied. Ntc 44034 configuration When finished, instrument returns previous menu entry. Field correction FEMA · MANUFACTURING FOR INDUSTRIAL AUTOMATION...
- Page 23 Force set Filter for 50 Hz and 60 Hz Key ‘LE’ Input signal value Average filter 0 to 100 (messages function) Output signal value ‘Dead band’ 0.0 to 100.0% Label Version Process value Password Percentage Factory reset w w w. fema . es...
-
Page 24: Factory Default Parameters
Display underrange. The display value should be lower than the ‘d.udr’ • the instrument is in ‘normal mode’ of operation minimum value that can be displayed. Function not available. For the actual configuration, the function is ‘-nA-’ not available. FEMA · MANUFACTURING FOR INDUSTRIAL AUTOMATION... -
Page 25: Precautions On Installation
Within the warranty period and after examination by the manufacturer, the unit will be repaired or substituted when found to be defective. Extended warranty available at (see section 3) w w w. fema . es... - Page 26 Notes FEMA · MANUFACTURING FOR INDUSTRIAL AUTOMATION...
- Page 27 SERIES I4 · Model I4P S ec t i on I N DU S T R I A L . I S O L AT E D S I G N AL C ON VERT ER S Notes w w w. fema . es...