Subscribe to Our Youtube Channel
Related Manuals for Sumake HLH-250
Summary of Contents for Sumake HLH-250
- Page 1 INSTRUCTION MANUAL HLH-250, HLH-500 ITEM NO.: HEAVY DUTY LEVER HOIST 1/4 (1/2) TON HLH-250(500)-I-1010A-W6...
- Page 2 WARNING ! This hoist should not be installed, operated or maintained by any person who has not read all the contents of these general instructions. Failure to read and comply with these instructions or any one of the limitations noted herein can result in serious bodily injury and/or property damage.
-
Page 3: Safety Precautions
NOTICE Upon receiving hoist, check immediately for evidence of damage during shipment. DO NOT USE a damaged hoist report damage to carrier. It is the responsibility of the owner/user to install, inspect, test, maintain and operate the hoist in accordance with the safety standard for lever hoists (ANSI/ASME B30.21) and OSHA standards. Any ANSI standard referenced in this manual may be purchased from American National Standards Institute, 11West 42 Street New York, NY10036. -
Page 4: After Operating
NOTE For hoists used as pullers-horizontal movement of load: when change lever is at UP, chain moves clockwise. When lever is at DOWN, chain moves counterclockwise. Change lever at center position is for free wheeling. NEVER MOVE CHAIN TO THE EXTREME IN EITHER DIRECTION Brake is always active, regardless of direction of movement UP or DOWM. - Page 5 Capacity Diameter Of Maximum Allowable (kg) Chain Wire Gauge Length Φ4 mm 11 links = 132nmm Φ5 mm 11 links = 165mm TABLE 1 An authorized person must determine whether conditions detected during inspection (such as corrosion, wear, ect.) are sufficient to warrant replacement of chain. When chain must be replaced, inspect other load bearing parts and replace (if necessary) at the same time.
-
Page 6: Test Certificate
LUBRICATION Keep hoist well lubricated at all times. Lubricate as noted under after operating. Use the following: OIL : AGMA No. 2 (Duro AW100) GREASE : NLGI No. 2 TEST CERTIFICATE It is hereby certified that this product was manufactured under our single-unit control of quality and was passed in strict inspection in accordance with our inspection standard. -
Page 7: Ec Declaration Of Conformity
DECLARATION OF CONFORMITY SUMAKE INDUSTRIAL CO., LTD. 4F, No. 351, Yangguang St., Neihu District, Taipei City, Taiwan declare in sole responsibility that the equipment Equipment： HEAVY DUTY LEVER HOIST 1/4(1/2) TON Model/ Serial No.： HLH-250(500) to which this declaration applies, complies with these normative documents: ... - Page 8 HLH-250 HEAVY DUTY LEVER HOIST (1/4 TON) PARTS LIST Parts No. Description Q'ty Parts No. Description Q'ty HLH250-01 Pinion Nut HLH250-21 Label HLH250-02 Washer HLH250-22 Brake Pawl HLH250-03 Grip Ring HLH250-23 Pawl Spring HLH250-04 Snap Ring HLH250-24 Brake Pawl Bolt...
- Page 9 HLH-500 HEAVY DUTY LEVER HOIST (1/2 TON) PARTS LIST Parts No. Description Q'ty Parts No. Description Q'ty HLH500-01 Pinion Nut HLH500-18 Plate HLH500-02 Washer HLH500-19 Plate Cover HLH500-03 Grip Ring HLH500-20 Nut For Plate Cover HLH500-04 Snap Ring HLH500-21 Cover Label HLH500-05 Fixing Plate HLH500-22...
- Page 12 NOTE www.SUMAKE.com www.AIRCOMPRESSOR.com.tw...
Need help?
Do you have a question about the HLH-250 and is the answer not in the manual?
Questions and answers