Subscribe to Our Youtube Channel
Related Manuals for Sumake SA-22015T8
Summary of Contents for Sumake SA-22015T8
- Page 1 INSTRUCTION MANUAL SA-22015T8, SA-22025T8 ITEM NO.: SA-22035T8, SA-22050T8 SA-22065T8 SPRING BALANCER SA-22015(25)(35)(50)(65)T8-I-2206B-YM...
-
Page 2: Safety Instructions On Use
Caution Prohibition 1. Safety instructions on use Incorrect use of the spring balancer could cause personal injury. Observe instruction in the manual and use the balancer correctly. Never stand under the spring balancer. Be careful to disassembly. Never put the spring balancer in fluid. - Page 3 Don’t twist and rub the cordage with cable during travel. Don’t load over its capacity. 1. Take the suspended tools off while remove the spring balancer, prevent the devise drop down. 2. Please remove the spring balancer and tools if rest for a long time. 3.
-
Page 4: Description Of Product
2. Description of product (1) Specifications Model Capacity Net Weight Travel Hose I.D. SA-22015T8 0.5 - 1.5 kg 1.9 kg 1.3 m 8 x12 SA-22025T8 1.5 - 2.5 kg 2.0 kg 1.3 m... -
Page 5: Checks Before Use
(1) Attach the joint to balancer and connect the air supplying hose to the joint (Fig-1) NOTE: Leave some slack in the hose to allow the balancer to rotate freely. (2) Prepare a fitting that can support at lest 10 times the maximum capacity of the balancer. NOTE: The fitting must have no opening to prevent the balancer from disengaging when it swings. -
Page 6: Troubleshooting
(1) Only removing the suspended tool/device when the hose is fully retracted. (2) Attach a new tool/device and then adjust spring tension according to Items “5” Spring tension adjustment ". 7. Troubleshooting. ⚫ If a malfunction occurs during operation, stop operation immediately and take the necessary steps to rectify the problem. - Page 7 ⚫ Make the inspection interval short the when operating frequently or under hostile environments.(See Fig3) Fig-3 (1) Inspect the accessories if they are correctly fixed and replace the worn parts. (2) Check the latch if it is becoming deformed. (3) Make sure the shaft is moving freely and stably. (4) The casing should be no broken or damage.
- Page 8 A. Remove the air supplying hose from joint. B. Lift then remove the tool/device from Swivel Joint(#31) when Hose(#24) is fully retracted into Drum(#20). C. Remove the balancer from the fitting or the supporting member and place on the table. D.
- Page 9 *** Use lithium saponified silicom grease corresponding to the No.2 class of the NLGI (Nat. lubrication Grease Just). (b) Attach Joint(#21) on Copper Joint(#33) and push until Joint(#21) touches the washer (see Fig-5). (c) Attach new O-Ring(A) shown in Fig-4 into the other groove of Copper Joint(#33) and lubricate with grease.
- Page 10 Baffle(#16) can move smoothly after inst ailing Cover(#18). (see Fig-8) F. Wind Spring(#19) by turning Worm(#8) to the"+" side (clockwise) After Hose is fully retracted, turn Worm by the number of turns shown in Table.1. Table 1 SA-22015T8 SA-22025T8 SA-22035T8 SA-22050T8...
-
Page 11: Ec Declaration Of Conformity
DECLARATION OF CONFORMITY SUMAKE INDUSTRIAL CO., LTD. 4F, No. 351, Yangguang St., Neihu District, Taipei City, Taiwan declare in sole responsibility that the equipment Equipment： SPRING BALANCER Model/ Serial No.： SA-22015(22025)(22035)(22050)(22065)T8 to which this declaration applies, complies with these normative documents: ... -
Page 12: Parts List
SA-22015T8 SPRING BALANCER (0.5-1.5KG) SA-22025T8 SPRING BALANCER (1.5-2.5KG) SA-22035T8 SPRING BALANCER (2.5-3.5KG) SA-22050T8 SPRING BALANCER (3.5-5.0KG) SA-22060T8 SPRING BALANCER (5.0-6.5KG) PARTS LIST Parts No. Description Q'ty Parts No. Description Q'ty Casing Set [Incl. 1, 2, 3, 4, 5, Spring Plate Set [Incl. 19, 20]...
Need help?
Do you have a question about the SA-22015T8 and is the answer not in the manual?
Questions and answers