Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for OTC Audien BTE
Summary of Contents for OTC Audien BTE
- Page 1 Audien U S E R M A N U A L...
- Page 2 ● You hear ringing or buzzing in only one ear. This OTC hearing aid is for users who are 18 and older. People who are younger than 18 with hearing loss 3.WARNING:This hearing aid should not cause pain when inserting it.
- Page 3 WARNING 6.Caution: You might need medical help if a piece gets stuck in your ear. Follow all the facility rules and posted instructions in areas where wireless network use its prohibited. If any part of your hearing aid, like the eartip, gets stuck in your ear, and you can't easily remove it with your 9.Note: Tell FDA about injuries, malfunctions, or other adverse events.
-
Page 4: Table Of Contents
TA B L E O F C O N T E N T S Device Diagram 1, 2 Package Contents Setting Up Your Device Fitting Your Ear Domes Switching Between Modes It’s time to Adjusting Volume Inserting Into Ear hear again. Power On/Off Charging Your Device Light Key... -
Page 5: Device Diagram
DEVICE DIAGRAM Charging Case Cover Ear Tube Microphone 1 Red = Right Ear Left Charging Port Microphone 2 Ear Dome Right Charging Port Volume Up (Press for 1 second) Charging Indicator Charging Indicator Mode Switch (Press for 3 seconds) Light for Left Ear Light for Right Ear (Light 1) (Light 3) -
Page 6: Package Contents
PA C K A G E C O N T E N T S Fitting Your Ear Domes Your Audien BTE comes with small, medium and large sizes of Ear Domes. To remove an Ear Dome from your device, simply pull with enough force until it pops off. -
Page 7: Switching Between Modes
ADJUSTING THE VOLUME Switching between Modes Adjusting Volume To change between the 4 environmental modes on your Audien Higher volume: BTE, press on the volume up button for 3 seconds. The amount of Press the volume up button for 1 second to increase the volume. beeps that you hear after the 3 seconds indicates which mode you are on. -
Page 8: Inserting Into Ear
Inserting Into Ear There are two methods to turn the Audien BTE on or off. Turn on: Remove the Audien BTE from the charging case, and it will Step 1: Insert the ear dome into your ear canal. automatically turn on. -
Page 9: Charging Your Device
Audien Light 1 Light 3 Step 2 Step 1 BTE units and their charging Insert the Audien BTE units solid white = solid white = Plug the charging case case. On average, a full charge into the charging port. -
Page 10: Cleaning Your Device
CLEANING YOUR DEVICE Cleaning Your Device Audien BTE Cleaning Use a soft cloth or tissue to clean the body of the Audien BTE, Dome Cleaning including the push buttons, charging contacts, shell, etc. Do not use alcohol, water, or other cleaning solvents to clean the Audien BTE Use the included cleaning brush to remove earwax, dust, and any as it may damage them. -
Page 11: Product Care
CLEANING YOUR DEVICE Product Care: -Keep your Audien BTE and charging case clean. Extreme temperatures (hot or cold), moisture, and foreign substances may damage the product. -Regular cleaning is necessary. -Charging contacts should always be kept clean and dry. -Using the provided cleaning brush keep the charging ports clear of dust or dirt. - Page 12 -Do not remove the batteries from the Audien BTE or charging case -Recharge the Audien BTE and charging case at least once a week. No power for extended periods of time may damage the battery.
- Page 13 TECHNICAL SPECIFICATIONS Max Output (OSPL90) 110dB Full-on gain value (HFA FOG@50) 37dB Total harmonic distortion value 0.70% Self-generated noise value 18dB Latency value F1<200Hz Frequency response bandwidth F2=7100Hz Frequency response smoothness Item Charging Case Charging box Input voltage d.c.5.0V Charging box Input current Charging box Output current 80mA Working Voltage...
-
Page 14: Precautions
PRECAUTIONS This information and other labeling, including the REGULATORY AND LEGAL INFORMATION user instructional brochure, are available on the internet at: Important information regarding Electro Magnetic Compatibility (EMC) support@audienhearing.com You may also call 205-255-1112 or write to support@audienhearing.com or With the increased number of electronic devices such as PC and mobile (cellular) telephones, radio trans- 10733N FLW Blvd#103, Scottsdale, AZ85259 to request a paper copy of this information &... - Page 15 LEGAL INFORMATION 1. Guidance and manufacture’s declaration - electromagnetic emission-for all EQUIPMENT and Radiated CISPR 11, SYSTEMS. emission Class B , Pass test Group 1 Guidance and manufacturer’s declaration-electromagnetic emission The hearing-aids are suitable for use in all Hearing aids are intended for use in the electromagnetic environment specified below. The customer Harmonic establishments, other of the user of hearing aids should assure that it is used in such an environment.
- Page 16 LEGAL INFORMATION 2. Guidance and manufacture’s declaration - electromagnetic immunity-for all EQUIPMENT 10V/m,80MHz 10V/m,80MHz Radiated RF and SYSTEMS. -2.7GHz 80% AM at 1KHz -2.7GHz 80% AM at 1KHz electromagnetic RF Band (IEC RF Band(IEC fields immunity test Guidance and manufacturer’s declaration-electromagnetic immunity for all equipment and systems. 60601-1-2:2014+ 60601-1-2:2014+ A1:2020 section 8.10 table 9)
- Page 17 LEGAL INFORMATION 3. Guidance and manufacture’s declaration – electromagnetic immunity-for EQUIPMENT and 0% UT; 0.5 cycles At 0°, SYSTEM that are not LIFE-SUPPORTING. 45°, 90°, 135°, 180°, 225°, 270° and 315° Guidance and manufacturer’s declaration-electromagnetic immunity for equipment and system Voltage dips, that are not life-supporting.
- Page 18 LEGAL INFORMATION Portable and mobile RF communications equipment should be used no closer to any NOTE 1 At 80 MHz and 800 MHz, the higher frequency range applies. part of hearing aids, including cables, than the recommended separation distance NOTE 2 These guidelines may not apply in all situations. Electromagnetic propagation is affected by calculated from the equation applicable to the frequency of the transmitter.
- Page 19 LEGAL INFORMATION 4. Recommended separation distances between portable and mobile RF communications 0.38 0.38 0.73 equipment and hearing aids. Hearing aids are intended for use in an electromagnetic environment in which radiated RF disturbances are controlled. The customer or the user of hearing aids can help prevent electromagnetic interference by maintaining a minimum distance between portable and mobile RF communications equipment (transmitters) and hearing aids as recommended below, according to the maximum output power of the communications equipment.
Need help?
Do you have a question about the Audien BTE and is the answer not in the manual?
Questions and answers
Can Audien Atom Pro be connected to my TV
The OTC Audien BTE hearing aids amplify speech and improve sound clarity, making them useful for hearing TV dialogue. However, there is no mention of direct connectivity to a TV.
This answer is automatically generated