Download Print this page

Advertisement

Quick Links

All manuals and user guides at all-guides.com
SERVICE MANUAL
AGB-21G

Advertisement

loading
Need help?

Need help?

Do you have a question about the Orion AGB-21G and is the answer not in the manual?

Questions and answers

Summary of Contents for Apollo Orion AGB-21G

  • Page 1 All manuals and user guides at all-guides.com SERVICE MANUAL AGB-21G...
  • Page 2 All manuals and user guides at all-guides.com...
  • Page 3 THIS MACHINE IS DESIGNED STRICTLY Congratulations on your purchase of an FOR COMPETITION USE, ONLY ON A Apollo AGB-21G. CLOSED COURSE. It is illegal for this machine to be operated on any public street, road, or highway. Off-road use on public lands As improvements are made on this model, may also be illegal.
  • Page 4 All manuals and user guides at all-guides.com 6. GASOLINE CAN CAUSE INJURY. If you should swallow some gasoline, inhale excess gasoline vapors, or allow any gasoline to get into your eyes, contact a doctor immediately. If any gasoline spills onto your skin or clothing, immediately wash skin areas with soap and water, and change your clothes.
  • Page 5 All manuals and user guides at all-guides.com TO THE NEW OWNER HOW TO USE THIS MANUAL This manual will provide you with a good basic understanding of features, operation, and PARTICULARLY IMPORTANT basic maintenance and inspection items of this machine. Please read this manual carefully INFORMATION and completely before operating your new machine.
  • Page 6 All manuals and user guides at all-guides.com INDEX GENERAL INFORMATION SPECIFICATIONS REGULAR INSPECTION AND ADJUSTMENTS ENGINE CHASSIS ELECTRICAL...
  • Page 7 All manuals and user guides at all-guides.com DESCRIPTION GENERAL INFORMATION DESCRIPTION Clutch lever NOTE: Engine stop switch The machine you have purchased may differ Front brake lever slightly from those shown in the following. Throttle grip Designs and specifications are subject to Fuel tank cap change without notice.
  • Page 8 All manuals and user guides at all-guides.com MACHINE IDENTIFICATION MACHINE IDENTIFICATION There are two significant reasons for knowing the serial number of your machine: 1. When ordering parts, you can give the number to your dealer for positive identification of the model you own. 2.
  • Page 9 All manuals and user guides at all-guides.com IMPORTANT INFORMATION IMPORTANT INFORMATION PREPARATION FOR REMOVAL AND DISASSEMBLY 1. Remove all dirt, mud, dust, and foreign material before removal and disassem- bly. When washing the machine with high pressured water, cover the parts follows. Silencer exhaust port Side cover air intake port 2.
  • Page 10 All manuals and user guides at all-guides.com IMPORTANT INFORMATION GASKETS, OIL SEALS AND O-RINGS 1. All gaskets, oil seals, and O-rings should be replaced when an engine is over- hauled. All gasket surfaces, oil seal lips, and O-rings must be cleaned. 2.
  • Page 11 All manuals and user guides at all-guides.com CHECKING OF CONNECTION CHECKING OF CONNECTION Dealing with stains, rust, moisture, etc. on the connector. 1. Disconnect: Connector 2. Dry each terminal with an air blower. 3. Connect and disconnect the connector two or three times. 4.
  • Page 12 All manuals and user guides at all-guides.com SPECIAL TOOLS SPECIAL TOOLS The proper special tools are necessary for complete and accurate tune-up and assembly. Using the correct special tool will help prevent damage caused by the use of improper tools or improvised techniques.
  • Page 13 All manuals and user guides at all-guides.com CONTROL FUNCTIONS CONTROL FUNCTIONS ENGINE STOP SWITCH The engine stop switch ① is located on the left handlebar. Continue pushing the engine stop switch till the engine comes to a stop. CLUTCH LEVER The clutch lever ②...
  • Page 14 All manuals and user guides at all-guides.com CONTROL FUNCTIONS FRONT BRAKE LEVER The front brake lever ① is located on the right handlebar. Pull it toward the handlebar to acti- vate the front brake. REAR BRAKE PEDAL The rear brake pedal ① is located on the right side of the machine.
  • Page 15 All manuals and user guides at all-guides.com GENERAL SPECIFICATIONS SPECIFICATIONS AGB-21G Dimensions: l l a , 1, l l a l l a Minimum ground clearance 260 mm Basic weight: 66kg l i o l l u Engine: Air cooled 4-stroke n i l n i l n i l...
  • Page 16 All manuals and user guides at all-guides.com GENERAL SPECIFICATIONS Oil capacity: Engine oil With oil filter replacement 0.85 L l i f Fuel: n i l research octane number of 90 or higher. Premium gasoline y t i Carburetor: Z26-5K JINGKE Spark plug: A7RTC/NGK...
  • Page 17 All manuals and user guides at all-guides.com GENERAL SPECIFICATIONS Brake: Suspension: n i l Shock absorber: l i o Wheel travel: Electrical: 2 - 3...
  • Page 18 All manuals and user guides at all-guides.com MAINTENANCE SPECIFICATIONS ENGINE Cylinder head: - - - Cylinder: ---- - - - Camshaft: ) t f - - - Camshaft cap inside diameter ---- 32.009 ~ 32.034 mm Camshaft outside diameter ---- 31.963 ~ 31.979 mm - t f Cam dimensions...
  • Page 19 All manuals and user guides at all-guides.com MAINTENANCE SPECIFICATIONS Timing chain: Timing chain type / No. of links 90T/90 ---- c i t - - - Valve, valve seat, valve guide: Valve clearance (cold) 0.02 ~ 0.04 mm ---- 0.02 ~ 0.04 mm ---- Valve dimensions: Head Diameter...
  • Page 20 All manuals and user guides at all-guides.com MAINTENANCE SPECIFICATIONS i l t - - - Valve seat width 0.8 ~ 1.2 mm 1.6 mm 0.8 ~ 1.2 mm 1.6 mm Valve spring: 35.55 mm 34.0 mm Set length (valve closed) 22.45 mm ---- 25.45 mm...
  • Page 21 All manuals and user guides at all-guides.com MAINTENANCE SPECIFICATIONS Piston pin bore inside diameter 14.002 ~ 14.013 mm 14.04 mm Piston pin outside diameter 13.994 ~ 14.000 mm 13.98 mm Piston rings: Top ring: - - - Dimensions (B 2.00mm ---- e l l 0.60 mm...
  • Page 22 All manuals and user guides at all-guides.com MAINTENANCE SPECIFICATIONS Clutch: t c i 2.7 mm y t i - - - - - - y t i - - - - - - y t i - - - ---- ---- - - - Shifter:...
  • Page 23 All manuals and user guides at all-guides.com MAINTENANCE INTERVALS REGULAR INSPECTION AND ADJUSTMENTS MAINTENANCE INTERVALS The following schedule is intended as a general guide to maintenance and lubrication. Bear in mind that such factors as weather, terrain, geographical location, and individual usage will alter the required maintenance and lubrication intervals.
  • Page 24 All manuals and user guides at all-guides.com MAINTENANCE INTERVALS Every Every After Every As re- third fifth Item Remarks break-in race quired 500 km) 1,000 km) SHIFT FORK, SHIFT CAM, GUIDE BAR Inspect Inspect wear ROTOR NUT Retighten EXHAUST PIPE, SILENCER, PRO- TECTOR Inspect and retighten Clean...
  • Page 25 All manuals and user guides at all-guides.com MAINTENANCE INTERVALS Every Every After Every As re- third fifth Item Remarks break-in race quired 500 km) 1,000 km) FRONT FORKS Inspect and adjust Replace oil Replace oil seal FRONT FORK OIL SEAL AND DUST SEAL Clean and lube REAR SHOCK ABSORBER...
  • Page 26 All manuals and user guides at all-guides.com PRE-OPERATION INSPECTION AND MAINTENANCE PRE-OPERATION INSPECTION AND MAINTENANCE Before riding for break-in operation, practice or a race, make sure the machine is in good operating condition. Before using this machine, check the following points. GENERAL INSPECTION AND MAINTENANCE Check that a fresh gasoline is filled in the fuel tank.
  • Page 27 All manuals and user guides at all-guides.com CLUTCH ADJUSTMENT CLUTCH ADJUSTMENT 1. Check: Clutch lever free play Out of specification Adjust. Clutch lever free play 5 ~ 10 mm 2. Adjust: Clutch lever free play Clutch lever free play adjustment steps: Loosen the locknuts ①...
  • Page 28 All manuals and user guides at all-guides.com THROTTLE CABLE ADJUSTMENT/ THROTTLE LUBRICATION THROTTLE LUBRICATION 1. Remove: Screw (throttle grip cap) 2. Apply: Lithium soap base grease On the throttle cable end 3. Install: Screw (throttle grip cap) 4 Nm (0.4 m · kg) AIR FILTER REPLACE NOTE: Proper air filter maintenance is the biggest key...
  • Page 29 All manuals and user guides at all-guides.com ENGINE OIL LEVEL INSPECTION 2. Install: Fitting Screw 5 Nm (0.5 m · kg) ENGINE OIL LEVEL INSPECTION 1. Start the engine, warm it up for several minutes, and then turn off the engine and wait for five minutes.
  • Page 30 All manuals and user guides at all-guides.com ENGINE OIL LEVEL INSPECTION 4. Inspect: Oil level Oil level should be between maximum and minimum marks. Oil level is low Add oil to proper level. NOTE: When inspecting the oil level, do not screw the oil tank cap into the oil tank.
  • Page 31 All manuals and user guides at all-guides.com ENGINE OIL REPLACEMENT ENGINE OIL REPLACEMENT 1. Start the engine and warm it up for sev- eral minutes, and then turn off the engine and wait for five minute. 2. Place the machine on a level place and hold it on upright position by placing the suitable stand under the engine.
  • Page 32 All manuals and user guides at all-guides.com PILOT SCREW ADJUSTMENT ENGINE IDLING SPEED ADJUSTMENT PILOT SCREW ADJUSTMENT 1. Adjust: Pilot screw ① Adjustment steps: NOTE: To optimize the fuel flow at a smaller throttle opening, each machine’s pilot screw has been individually set at the factory.
  • Page 33 All manuals and user guides at all-guides.com CHASSIS/BRAKE SYSTEM AIR BLEEDING CHASSIS BRAKE SYSTEM AIR BLEEDING WARNING ① Bleed the brake system if: The system has been disassembled. A brake hose has been loosened or removed. The brake fluid is very low. The brake operation is faulty.
  • Page 34 All manuals and user guides at all-guides.com FRONT BRAKE ADJUSTMENT REAR BRAKE ADJUSTMENT NOTE: If bleeding is difficult, it may be necessary to let the brake fluid system stabilize for a few hours. Repeat the bleeding procedure when the tiny bubbles in the system have disap- peared.
  • Page 35 All manuals and user guides at all-guides.com FRONT BRAKE PAD INSPECTION AND REPLACEMENT FRONT BRAKE PAD INSPECTION AND REPLACEMENT 1. Inspect: Brake pad thickness A Out of specification Replace as a set. Brake pad thickness: 4.0 mm <Limit>: 1.0 mm 2.
  • Page 36 All manuals and user guides at all-guides.com REAR BRAKE PAD INSPECTION AND REPLACEMENT REAR BRAKE PAD INSPECTION AND REPLACEMENT 1. Inspect: Brake pad thickness A Out of specification Replace as a set. Brake pad thickness: 4 mm <Limit>: 1.0 mm 2.
  • Page 37 All manuals and user guides at all-guides.com REAR BRAKE PAD INSPECTION AND REPLACEMENT CAUTION: Do not reuse the drained brake fluid. Tighten the bleed screw 1 and 2. Bleed screw 1 and 2: 18 Nm (1.8m Nut 3 (brake caliper): 20 Nm (2.0m 3.
  • Page 38 All manuals and user guides at all-guides.com SPROCKETS INSPECTION/DRIVE CHAIN INSPECTION SPROCKETS INSPECTION 1. Inspect: Sprocket teeth a Excessive wear Replace. NOTE: Replace the drive sprocket, rear wheel sprocket and drive chain as a set. DRIVE CHAIN INSPECTION 1. Remove: Master link clip Joint Drive chain...
  • Page 39 All manuals and user guides at all-guides.com DRIVE CHAIN SLACK ADJUSTMENT 5. Install: Drive chain Joint Master link clip CAUTION: Be sure to install the master link clip to the direction as shown. A A Turning direction 6. Lubricate: Drive chain Drive chain lubricant: SAE 10W-30 motor oil or suit- able chain lubricants...
  • Page 40 All manuals and user guides at all-guides.com FRONT FORK INSPECTION 3. Adjust: Drive chain slack Drive chain slack adjustment steps: Loosen the axle nut ① and locknuts ② . Adjust the drive chain slack by turning the adjusters ③ . Turn the adjuster ③...
  • Page 41 All manuals and user guides at all-guides.com CHECKING THE BATTERY ELECTRICAL SYSTEM CHECKING THE BATTERY WARNING Batteries generate explosive hydrogen gas and contain electrolyte which is made of poisonous and highly caustic sulfuric acid. Therefore, always follow these preventive measures: Wear protective eye gear when handling or working near batteries.
  • Page 42 All manuals and user guides at all-guides.com CHECKING THE BATTERY CAUTION: Add only distilled water. Tap water contains minerals which are harmful to the battery. 3. Charge: battery Battery charging amperage and time 0.4 amps/10 hrs WARNING Do not quick charge a battery. CAUTION: To ensure maximum performance, always charge a new battery before using it.
  • Page 43 All manuals and user guides at all-guides.com CHECKING THE FUSES REAR SHOCK ABSORBER INSPECTION CHECKING THE FUSE The following procedure applies to all of the fuses. CAUTION: To avoid a short circuit, always turn the main switch to “OFF” when checking or replacing a fuse.
  • Page 44 All manuals and user guides at all-guides.com REAR SHOCK ABSORBER SPRING PRELOAD ADJUSTMENT REAR SHOCK ABSORBER SPRING PRELOAD ADJUSTMENT 1. Elevate the rear wheel by placing the suitable stand under the engine. 2. Remove: Rear frame 3. Loosen: ① Locknut 4.
  • Page 45 All manuals and user guides at all-guides.com TIRE PRESSURE CHECK/SPOKES INSPECTION AND TIGHTENING/WHEEL INSPECTION TIRE PRESSURE CHECK 1. Measure: Tire pressure Out of specification Adjust. Standard tire pressure: 130 kPa ( 1.3 kgf/cm ) NOTE: Check the tire while it is cold. Loose bead stoppers allow the tire to slip off its position on the rim when the tire pressure is low.
  • Page 46 All manuals and user guides at all-guides.com STEERING HEAD INSPECTION AND ADJUSTMENT 2. Inspect: Bearing free play Exist play Replace. STEERING HEAD INSPECTION AND ADJUSTMENT 1. Elevate the front wheel by placing a suit- able stand under the engine. 2. Check: Steering stem Grasp the bottom of the forks and gen- tly rock the fork assembly back and...
  • Page 47 All manuals and user guides at all-guides.com STEERING HEAD INSPECTION AND ADJUSTMENT ③ Tighten the steering ring nut using steering nut wrench NOTE: Apply the lithium soap base grease on the thread of the steering stem. Set the torque wrench to the steering nut wrench so that they form a right angle.
  • Page 48 All manuals and user guides at all-guides.com ELECTRICAL/SPARK PLUG INSPECTION ELECTRICAL SPARK PLUG INSPECTION 1. Remove: Spark plug 2. Inspect: Electrode ① Wear/damage Replace. Insulator color ② Normal condition is a medium to light tan color. Distinctly different color Check the engine condition.
  • Page 49 All manuals and user guides at all-guides.com IGNITION TIMING CHECK IGNITION TIMING CHECK 1. Remove: Timing mark accessing screw 2. Check: Ignition timing Checking steps: Start the engine and let it warm up. Let the engine run at the specified speed. Engine speed: 1,400 ~ 1,600 r/min Visually check the stationary pointer...
  • Page 50 All manuals and user guides at all-guides.com ENGINE SEAT, FUEL TANK AND SIDE COVERS SEAT, FUEL TANK AND SIDE COVERS Order Job / Part name Q’ty Remarks Remove the parts in the order listed. LEFT TANK COVER RIGHT TANK COVER SEAT LEFT FENDER PLATE RIGHT FENDER PLATE...
  • Page 51 All manuals and user guides at all-guides.com SEAT, FUEL TANK AND SIDE COVERS REMOVAL POINTS Fuel Tank , Side covers and Seat Remove: Bolt for Tank Cover Seat Bolt Bolt for Fuel Tank Fuel Tank Screw for Tank Cover and Seat Left Tank Cover Right Tank Cover Screw for Fender plate...
  • Page 52 All manuals and user guides at all-guides.com EXHAUST PIPE AND SILENCER EXHAUST PIPE AND SILENCER Order Job / Part name Q’ty Remarks Remove the parts in the order listed. BOLT HOOP RUBBER MAT NUT M6×14 EXHAUST MUFFLER EXHAUST PIPE SEAL For installation, reverse the removal procedure.
  • Page 53 All manuals and user guides at all-guides.com EXHAUST PIPE AND SILENCER INSPECTION Silencer and exhaust pipe 1. Inspect: Gasket ① Damage Replace. ASSEMBLY AND INSTALLATION Silencer and exhaust pipe 1. Install: Gasket ① Exhaust muffler (exhaust pipe) 15 Nm (1.5 m • kg) 2.
  • Page 54 All manuals and user guides at all-guides.com CRBURETOR & AIR-FITER CRBURETOR & AIR-FITER Order Job / Part name Q’ty Remarks Remove the parts in the order listed. SCREW FOR AIR-FITER CLAMP AIR-FITER CRBURETOR GASKET,HEAT INSULATING, CRBURETOR O-RING INLET PIPE O-RING GASKET For installation, reverse the removal procedure.
  • Page 55 All manuals and user guides at all-guides.com CARBURETOR DISASSEMBLY CARBURETOR DISASSEMBLY Order Job / Part name Q’ty Remarks Remove the parts in the order listed. UPPER COVER GASKET,UPPER COVER RETURN SPRING,AIR THROTTLE V-CLIP E-CIRCLIP NEEDLE,JET AIR THROTTLE O-RING ADJUSTING SCREW,AIR THROTTLE SPRING,ADJUSTING SCREW O-RING WASHER...
  • Page 56 All manuals and user guides at all-guides.com CARBURETOR DISASSEMBLY CARBURETOR DISASSEMBLY Order Job / Part name Q’ty Remarks Remove the parts in the order listed. FLOAT COMP NEEDLE VALVE,CARBURETOR FLOAT HOOK,NEEDLE VALVE FLOAT PIN GASKET,FLOAT CHAMBER DRAIN SCREW O-RING SCREW UNIT,FLOAT CHAMPER PIPE CLIP HOSE For installation, reverse the removal procedure.
  • Page 57 All manuals and user guides at all-guides.com CARBURETOR INSPECTION Carburetor 1. Inspect: Carburetor body Contamination → Clean. NOTE: Use a petroleum based solvent for cleaning. Blow out all passages and jets with com- pressed air. Never use a wire. 2. Inspect: Adjust Screw,Mixture ①...
  • Page 58 All manuals and user guides at all-guides.com SPROCKET REPLACEMENT SPROCKET REPLACEMENT Order Job / Part name Q’ty Remarks Remove the parts in the order listed. COVER,L.RR.CRANKCASE INITIATIVE CHAIN DRIVER RIVET PLANK DRIVING GEAR SHIFT PEDAL GUAGE OIL LEVER KICK STARTER SPARK PLUG CAP ENGINE SKID PLATE SIDE STAND...
  • Page 59 All manuals and user guides at all-guides.com CYLINDER HEAD CYLINDER HEAD Order Job / Part name Q’ty Remarks Remove the parts in the order listed. Spark plug Bolt M6 x 110 Cylinder cover L / Gasket Timing driven sprocket Valve cover / O-ring Valve cover / O-ring Cylinder cover Gasket,cylinder cover...
  • Page 60 All manuals and user guides at all-guides.com CYLINDER HEAD REMOVING THE CYLINDER HEAD 1. Remove: Long Bolt A Nut B 2. Align: “I” mark a on the generator rotor (with the stationary pointer b on the crankcase cov- a. Turn the primary pulley counterclockwise. b.
  • Page 61 All manuals and user guides at all-guides.com CYLINDER HEAD 5 Remove Chain Tensioner Bolt 1 Washer 2 Spring Chain Tensioner Push Road ③ Chain Tensioner Push Road Assembly④ NOTE: To prevent the timing chain from falling into the crankcase, fasten it with a wire a . While holding the generator rotor bolt with a wrench, remove the bolt.
  • Page 62 All manuals and user guides at all-guides.com CYLINDER HEAD 6. Remove: cylinder head NOTE: Loosen the nuts in the proper sequence. Loosen each nut 1/2 of a turn at a time. After all of the nuts are fully loosened, remove them.
  • Page 63 All manuals and user guides at all-guides.com CYLINDER HEAD CHECKING THE TIMING CHAIN TENSIONER 1. Check: timing chain tensioner Cracks/damage Replace. CHECKING THE TAPPET COVERS AND CAMSHAFT SPROCKET COVER The following procedure applies to both of the tappet covers and O-rings. 1.
  • Page 64 All manuals and user guides at all-guides.com CYLINDER HEAD INSTALLING THE CAMSHAFT SPROCKET 1. Align: “I” mark on the generator rotor (with the mark on the generator rotor cover) a. Turn the crankshaft counterclockwise. b. When the piston is at TDC on the compres- sion stroke, align the “I”...
  • Page 65 All manuals and user guides at all-guides.com CAMSHAFT /VALVES AND VALVE SPRINGS CAMSHAFT /VALVES AND VALVE SPRINGS Order Job / Part name Q’ty Remarks Remove the parts in the order listed. RIGHT COVER,CYLINDER HEAD GASKET SHAFT,VALVE RROCKER ARM ADJUSTING NUT ADJUSTING SCREW VALVE RROCKER ARM CAM SHAFT...
  • Page 66 All manuals and user guides at all-guides.com CAMSHAFT /VALVES AND VALVE SPRINGS REMOVING THE ROCKER ARMS AND CAM- SHAFT 1. Loosen: locknuts 1 adjusting screws 2 2. Remove: intake rocker arm shaft ① exhaust rocker arm shaft ② intake rocker arm exhaust rocker arm 3.
  • Page 67 All manuals and user guides at all-guides.com CAMSHAFT /VALVES AND VALVE SPRINGS 2 Measure: camshaft lobe dimensions A Out of specification Replace the cam- shaft. Camshaft lobe dimension limit Intake 26.30 mm Exhaust 26.00 mm 3. Check: camshaft oil passage Obstruction Blow out with compressed air.
  • Page 68 All manuals and user guides at all-guides.com CAMSHAFT /VALVES AND VALVE SPRINGS 6. Calculate: rocker-arm-to-rocker-arm-shaft clearance NOTE: Calculate the clearance by subtracting the rock- er arm shaft outside diameter from the rocker arm inside diameter. Out of specification Replace the defective part(-s).
  • Page 69 All manuals and user guides at all-guides.com CAMSHAFT /VALVES AND VALVE SPRINGS REMOVING THE VALVES The following procedure applies to all of the valves and related components. NOTE: Before removing the internal parts of the cylin- der head (e.g., valves, valve springs, valve seats), make sure that the valves properly seal.
  • Page 70 All manuals and user guides at all-guides.com CAMSHAFT /VALVES AND VALVE SPRINGS CHECKING THE VALVES AND VALVE GUIDES The following procedure applies to all of the valves and valve guides. 1. Measure: valve-stem-to-valve-guide clearance Valve-stem-to-valve-guide clearance = Valve guide inside diameter a – Valve stem diameter b Out of specification Replace the valve...
  • Page 71 All manuals and user guides at all-guides.com CAMSHAFT /VALVES AND VALVE SPRINGS 3. Eliminate: carbon deposits (from the valve face and valve seat) 4. Check: valve face Pitting/wear Grind the valve face. valve stem end Mushroom shape or diameter larger than the body of the valve stem Replace the valve.
  • Page 72 All manuals and user guides at all-guides.com CAMSHAFT /VALVES AND VALVE SPRINGS a. Apply Mechanic’s blueing dye (Dykem) 1 onto the valve face. b. Install the valve into the cylinder head. c. Press the valve through the valve guide and onto the valve seat to make a clear pattern.
  • Page 73 All manuals and user guides at all-guides.com CAMSHAFT /VALVES AND VALVE SPRINGS e. Apply a fine lapping compound to the valve face and repeat the above steps. f. After every lapping procedure, be sure to clean off all of the lapping compound from the valve face and valve seat.
  • Page 74 All manuals and user guides at all-guides.com CAMSHAFT /VALVES AND VALVE SPRINGS INSTALLING THE VALVES The following procedure applies to all of the valves and related components. 1. Deburr: valve stem end (with an oil stone) 2. Lubricate: valve stem oil seal (with the recommended lubricant) Recommended lubricant...
  • Page 75 All manuals and user guides at all-guides.com CYLINDER AND PISTON CYLINDER AND PISTON Order Job / Part name Q’ty Remarks Remove the parts in the order listed. PIN SHAFT,GUIDEROLLER CAM CHAIN GUIDE ROLLER CYLINDER BLOCK GASKET,CYLINDER BLOCK DOWEL PIN RECTANGLE RING CIRCLIP,PISTON PIN PISTON PIN PISTON...
  • Page 76 All manuals and user guides at all-guides.com CYLINDER AND PISTON REMOVING THE PISTON AND PISTON RINGS 1. Remove: piston pin circlip 1 piston pin 2 piston 3 NOTE: Before removing the piston pin circlip, cover the crankcase opening with a clean towel or rag to prevent the circlip from falling into the crank- case cavity.
  • Page 77 All manuals and user guides at all-guides.com CYLINDER AND PISTON b. If out of specification, rebore or replace the cylinder, and replace the piston and piston rings as a set. c. Measure piston skirt diameter “P” with the micrometer. 1 7.0 mm from the bottom edge of the piston. Piston size “P”...
  • Page 78 All manuals and user guides at all-guides.com CYLINDER AND PISTON 2. Install: piston ring (into the cylinder) NOTE: Level the piston ring in the cylinder with the pis- ton crown as shown. a 5.0 mm 3. Measure: piston ring end gap Out of specification Replace the piston ring.
  • Page 79 All manuals and user guides at all-guides.com CYLINDER AND PISTON Piston-pin-to-piston clearance = Piston pin bore size b – Piston pin outside diameter a Piston-pin-to-piston clearance 0.002 0.019 mm INSTALLING THE PISTON AND CYLINDER 1. Install: top ring 1 2nd ring 2 upper oil ring rail oil ring expander lower oil ring rail 5...
  • Page 80 All manuals and user guides at all-guides.com CYLINDER AND PISTON 5. Offset: piston ring end gaps a Top ring b Lower oil ring rail c Upper oil ring rail d 2nd ring 6. Install: cylinder 1 NOTE: While compressing the piston rings with one hand, install the cylinder with the other hand.
  • Page 81 All manuals and user guides at all-guides.com CLUTCH CLUTCH 9 8 7 Order Job / Part name Q’ty Remarks Remove the parts in the order listed. DECORATE COVER,R CRANK CASE COVER GASKET,DECORATE COVER CLUTCHLEVER PIN CLUTCHLEVER ASSY CLUTCH CAM SHAFT SPRING O-RING CLUTCH SHIFTING PLATE CLUTCH PRESSURE PLATE...
  • Page 82 All manuals and user guides at all-guides.com CLUTCH CLUTCH 9 8 7 Order Job / Part name Q’ty Remarks Remove the parts in the order listed. GASKET,END COVER WASHER THURST WASHER CLUTCH ASSY DRIVER GEAR SLEEVE BUSH CIRCLIP DRIVEN GEAR CAM For installation, reverse the removal procedure.
  • Page 83 All manuals and user guides at all-guides.com CLUTCH CLUTCH 6 5 4 3 2 3 2 3 1 2 Order Job / Part name Q’ty Remarks Remove the parts in the order listed. CIRCLIP PLATE CLUTCH DRIVE FRICTION PLATE CLUTCH CENTER SLEEVE DRIVE PLATE CLUTCH CUSHION SPRING CLUTCH SPRING...
  • Page 84 All manuals and user guides at all-guides.com CLUTCH REMOVING THE CLUTCH 1. Remove: Screw 2. Straighten the lock washer tab ③ 3. Remove: clutch boss nut ① washer ② NOTE: While holding the clutch boss with the univer- sal clutch holder , loosen the clutch boss nut. 4.
  • Page 85 All manuals and user guides at all-guides.com CLUTCH 2. Measure: clutch plate warpage (with a surface plate and thickness gauge Out of specification Replace the clutch plates as a set. Clutch plate warpage limit Less than 0.1 mm CHECKING THE CLUTCH SPRINGS The following procedure applies to all of the clutch springs.
  • Page 86 All manuals and user guides at all-guides.com CLUTCH INSTALLING THE CLUTCH ASSY 1. Install: put the clutch spring ① into the clutch outer case. put the drive plate ② into the clutch outer case. 2. Lubricate: friction plates ③ upper plates ④ (with the recommended lubricant) Recommended lubricant Engine oil...
  • Page 87 All manuals and user guides at all-guides.com CLUTCH CHECKING THE CLUTCH PUSH RODS 1. Check: oil tube 1 oil thimble spring 2 oil thimble 3 Cracks/damage/wear Replace the de- fective part(-s). 2. Measure: oil thimble spring ② free length Out of specification Replace the oil thim- ble spring.
  • Page 88 All manuals and user guides at all-guides.com CLUTCH 4. Install: oil tube 1 oil thimble spring 2 oil thimble 3 screw 6 Nm (0.6 m • kg) 5. Check clutch assy NOTE: Make sure that the teeth on the lock washer are correctly aligned with the grooves on the clutch boss.
  • Page 89 All manuals and user guides at all-guides.com OIL PUMP OIL PUMP Order Job / Part name Q’ty Remarks Remove the parts in the order listed. OIL PUMP OIL FILTER SCREEN GEAR For installation, reverse the removal procedure. 4 - 40...
  • Page 90 All manuals and user guides at all-guides.com OIL PUMP REMOVING THE OIL PUMP 1. Remove: Screw ① - ③. 2. Remove: gasket of oil pump ① gear of oil pump ② NOTE: Remove the gasket of oil pump and check the state.Replace if worn or if reuse if questionable.
  • Page 91 All manuals and user guides at all-guides.com MAGNETO AND STARTER GEAR MAGNETO AND STARTER GEAR Order Job / Part name Q’ty Remarks Remove the parts in the order listed. FRONT COVER, LEFT CRANKCASE GASKET, LEFT CRANKCASE STATOR , MAGNETO COTOR , MAGNETO CIRCLIP 10 DRIVEN SPROCKET, STARTING MOTOR...
  • Page 92 All manuals and user guides at all-guides.com MAGNETO AND STARTER GEAR REMOVING THE GENERATOR ROTOR 1. Remove: bolt 1 (magneto) NOTE: Loosen the bolt (generator rotor) 1 while holding the rotor with a sheave holder 2 . Do not allow the sheave holder to touch the projection on the rotor.
  • Page 93 All manuals and user guides at all-guides.com MAGNETO AND STARTER GEAR 2. Check: starter clutch operation a. Hold the starter clutch. b. When turning the starter clutch gear clock- wise a , the starter clutch and the starter clutch gear should engage. If the starter clutch gear and starter clutch do not engage, the starter clutch is faulty and must be replaced.
  • Page 94 All manuals and user guides at all-guides.com MAGNETO AND STARTER GEAR INSTALLING THE GENERATOR ROTOR 1. Install: starter wheel gear woodruff key 2. Install: starting motor drive chain ① drive gear ② cirlip ③ bolt ④ chain protect plate ⑤ 3.
  • Page 95 All manuals and user guides at all-guides.com CAM CHAIN-TENSIOR CAM CHAIN-TENSIOR Order Job / Part name Q’ty Remarks Remove the parts in the order listed. CLIP, VOLTAGE WIRE LOWER PAN, OIL INSULATING O-RING OIL SEAL BOLT M14×1.5 WASHER SPRING, CHAIN TENSIONER PUSH CHAIN TENSIONER PUSH ROD TIGHTENING ROD HEAD TIMING CHAIN...
  • Page 96 All manuals and user guides at all-guides.com CAM CHAIN-TENSIOR CAM CHAIN TENSIOR 1. Remove: bolt of cam chain tensior ① roller of cam chain tensior 2 cam chain 3 2. Check: aluminium washer ① Pitting/Wear/Damage Replace. spring of chain tensior push rod Pitting/Wear/Damage Replace.
  • Page 97 All manuals and user guides at all-guides.com CRANKSHAFT AND GEARSHIFT ARM CRANKSHAFT AND GEARSHIFT ARM Order Job / Part name Q’ty Remarks Remove the parts in the order listed. BOLT, LOCATING PLATE LOCATING PLATE GROUP RETURN SPRING, LOCATING PLATE RETURN SPRING, GEARSHIFT LEVER BUSH GEARSHIFT LEVER BODY ASSY...
  • Page 98 All manuals and user guides at all-guides.com CRANKSHAFT AND GEARSHIFT ARM CRANKSHAFT AND GEARSHIFT ARM Order Job / Part name Q’ty Remarks Remove the parts in the order listed. CONTACT, GEAR INDICATION CYLINDER STUD BOLT B M7 X 204 CYLINDER STUD BOLT A M7 X 212 OIL DRAIN PLUG M12×1.5 WASHER 12.5×1.5×20 BOLT M6×65...
  • Page 99 All manuals and user guides at all-guides.com CRANKSHAFT AND GEARSHIFT ARM DISASSEMBLING THE CRANKCASE 1. Gearshift arm ①: Remove: bolt of locating plate ② bolt of locating plate ③ 2. Remove: cirlip ① spring ② spring seat ③ 4 - 50...
  • Page 100 All manuals and user guides at all-guides.com CRANKSHAFT DISASSEMBLING THE CRANKCASE 1. Remove: crankcase bolts NOTE: Loosen each bolt 1/4 of a turn at a time, in stages and in a crisscross pattern. After all of the bolts are fully loosened, remove them. Loosen the bolts in decreasing numerical or- der (refer to the numbers in the illustration).
  • Page 101 All manuals and user guides at all-guides.com CRANKSHAFT CRANKSHAFT Order Job / Part name Q’ty Remarks Remove the parts in the order listed. TIMING DRIVE SPROCKET BEARING (6205) BEARING (6205) ROLLER BEARING JOINT RED LEFT CRANKSHAFT RIGHT CRANKSHAFT For installation, reverse the removal procedure. 4 - 52...
  • Page 102 All manuals and user guides at all-guides.com CRANKSHAFT CHECKING THE CRANKSHAFT AND CON- NECTING ROD 1. Measure: crankshaft runout Out of specification Replace the crank- shaft, bearing or both. NOTE: Turn the crankshaft slowly. Crankshaft runout Less than 0.03 mm 2.
  • Page 103 All manuals and user guides at all-guides.com CRANKSHAFT CHECKING THE BEARINGS AND OIL SEALS 1. Check: bearings Clean and lubricate the bearings, then rotate the inner race with your finger. Rough movement Replace. 2. Check: oil seals Damage/wear Replace. CHECKING THE TIMING CHAIN, CAM- SHAFT SPROCKET, AND TIMING CHAIN GUIDES 1.
  • Page 104 All manuals and user guides at all-guides.com CRANKSHAFT INSTALLING THE CRANKSHAFT 1. Install: crankshaft 1 CAUTION: To avoid scratching the crankshaft and to ease the installation procedure, apply grease onto the oil seal lips and apply en- gine oil onto each bearing. ASSEMBLING THE CRANKCASE 1.
  • Page 105 All manuals and user guides at all-guides.com TRANSMISSION DEVICE,SHIFT DRUM ,GEAR FORKS TRANSMISSION DEVICE,SHIFT DRUM ,GEAR FORKS 14-1 Order Job / Part name Q’ty Remarks Remove the parts in the order listed. RATCHET SPRING PLATE WASHER 17 CIRCLIP SPRING RATCHET SPRING BASE STARING RATCHET WHEEL CIRCLIP WASHER...
  • Page 106 All manuals and user guides at all-guides.com TRANSMISSION DEVICE,SHIFT DRUM ,GEAR FORKS TRANSMISSION DEVICE,SHIFT DRUM ,GEAR FORKS 14-1 Order Job / Part name Q’ty Remarks Remove the parts in the order listed. MAINSHAFT COUNTERSHAFT BEARING 6203 BEARING 6201 BEARING 6001 BEARING 6203 OIL SEAL 17X29X5 For installation, reverse the removal procedure.
  • Page 107 All manuals and user guides at all-guides.com TRANSMISSION DEVICE,SHIFT DRUM ,GEAR FORKS REMOVING THE TRANSMISSION 1. Loosen: screw 1 2. Remove: screw 1 contact ,gear indication 2 3. Remove: drive axle assembly 1 main axle assembly 2 gearshift drum assy 3 Remove them at same the time.
  • Page 108 All manuals and user guides at all-guides.com TRANSMISSION DEVICE,SHIFT DRUM ,GEAR FORKS CHECKING THE SHIFT FORKS The following procedure applies to all of the shift forks and related components. Check: shift fork cam follower 1 shift fork pawl 2 Bends/damage/scoring/wear Replace the shift fork.
  • Page 109 All manuals and user guides at all-guides.com TRANSMISSION DEVICE,SHIFT DRUM ,GEAR FORKS CHECKING THE TRANSMISSION 1. Measure: main axle runout (with a centering device and dial gauge 1 ) Out of specification Replace the main axle. Main axle runout limit 0.02 mm 2.
  • Page 110 All manuals and user guides at all-guides.com TRANSMISSION DEVICE,SHIFT DRUM ,GEAR FORKS INSTALLING THE TRANSMISSION, SHIFT FORKS AND SHIFT DRUM 1. Install: main axle 1 drive axle 2 gearshift drum assy 3 Put them into the crankcase at same the time. 2.
  • Page 111 All manuals and user guides at all-guides.com FRONT WHEEL AND REAR WHEEL FRONT WHEEL Order Job / Part name Q’ty Remarks Remove the parts in the order listed. NUT(FRONT WHEEL AXLE) FRONT RIM AXLE FRONT TIRE COLLAR,FR.WHEEL OIL SEAL BEARING FRONT-BRAKE DISK For installation, reverse the removal procedure.
  • Page 112 All manuals and user guides at all-guides.com FRONT WHEEL AND REAR WHEEL REAR WHEEL Order Job / Part name Q’ty Remarks Remove the parts in the order listed. NUT(FRONT WHEEL AXLE) FRONT RIM AXLE CHAIN PULLER REAR WHEEL COLLAR,RE.WHEEL DRIVEN SPROKET OIL SEAL BEARING FRONT-BRAKE DISK...
  • Page 113 All manuals and user guides at all-guides.com FRONT WHEEL AND REAR WHEEL REMOVAL POINTS Rear wheel 1. Remove: Wheel ① NOTE: Push the wheel forward and remove the drive chain ② . Wheel bearing (if necessary) 1. Remove: Bearing ① NOTE: Remove the bearing using a general bearing puller ②...
  • Page 114 All manuals and user guides at all-guides.com FRONT WHEEL AND REAR WHEEL Wheel axle 1. Measure: Wheel axle bends Out of specification → Replace. Use the dial gauge ① . Wheel axle bending limit: 0.5 mm NOTE: The bending value is shown by one half of the dial gauge reading.
  • Page 115 All manuals and user guides at all-guides.com FRONT WHEEL AND REAR WHEEL ASSEMBLY AND INSTALLATION Front wheel 1. Install: Bearing (left) ① Middel spacer ② Bearing (right) ③ Oil seal ④ Collar (left) ⑤ Collar (right) ⑥ NOTE: Apply the lithium soap base grease on the bearing and oil seal lip when installing.
  • Page 116 All manuals and user guides at all-guides.com FRONT WHEEL AND REAR WHEEL 5. Install: Wheel axle ① NOTE: Apply the lithium soap base grease on the wheel axle. 6. Install: Nut (wheel axle) ② 50Nm (5 m · kg ) 5 - 6...
  • Page 117 All manuals and user guides at all-guides.com FRONT WHEEL AND REAR WHEEL Rear wheel 1. Install: Bearing (left) ① Bearing (right) ② Middle spacer ③ Oil seal ④ Left Collar ⑤ Right Collar ⑥ NOTE: Apply the lithium soap base grease on the bearing and oil seal lip when installing.
  • Page 118 All manuals and user guides at all-guides.com FRONT WHEEL AND REAR WHEEL 3. Install: Rear wheel sprocket ① Bolt (rear wheel sprocket) ② 25 Nm (2.5m · kg) Washer (rear wheel sprocket) ③ Nut (rear wheel sprocket) ④ NOTE: Tighten the nuts in stage, using a crisscross pattern.
  • Page 119 All manuals and user guides at all-guides.com FRONT WHEEL AND REAR WHEEL 7. Install: Left drive chain puller ① Wheel axle ② NOTE: Install the left drive chain puller, and insert the wheel axle from left side. Apply the lithium soap base grease on the wheel axle.
  • Page 120 All manuals and user guides at all-guides.com FRONT BRAKE AND REAR BRAKE FRONT BRAKE Order Job / Part name Q’ty Remarks Remove the parts in the order listed. FR,CALIPER ASSY. UNION BOLT FR,BRAKE HOSE BRAKE LEVER BRAKE MASTER CYLINDER BRACKET BRAKE MASTER CYLINDER For installation, reverse the removal procedure.
  • Page 121 All manuals and user guides at all-guides.com FRONT BRAKE AND REAR BRAKE REAR BRAKE Order Job / Part name Q’ty Remarks Remove the parts in the order listed. UNION BOLT. REAR,CALIPER ASSY. REAR,BRAKE HOSE REAR MASTER CYLINDER ASSY REAR.BRAKE PEDAL For installation, reverse the removal procedure.
  • Page 122 All manuals and user guides at all-guides.com FRONT WHEEL AND REAR WHEEL REMOVAL POINTS Brake fluid 1. Remove: [Front] Brake master cylinder cap ① NOTE: Do not remove the diaphragm. [Rear] Brake master cylinder cap ① NOTE: Do not remove the diaphragm. ı...
  • Page 123 All manuals and user guides at all-guides.com FRONT WHEEL AND REAR WHEEL Brake caliper piston 1. Remove: Brake caliper piston Use compressed air and proceed care- fully. WARNING Cover piston with rag and use extreme caution when expelling piston from cylin- der.
  • Page 124 All manuals and user guides at all-guides.com FRONT WHEEL AND REAR WHEEL 2. Inspect: Diaphragm ① Crack/damage → Replace. 3. Inspect: Brake master cylinder piston ① Brake master cylinder cup ② ② Wear/damage/score marks → Replace brake master cylinder kit. ①...
  • Page 125 All manuals and user guides at all-guides.com FRONT WHEEL AND REAR WHEEL ASSEMBLY AND INSTALLATION WARNING All internal parts should be cleaned in new brake fluid only. Internal parts should be lubricated with brake fluid when installed. Front braker caliper 1.
  • Page 126 All manuals and user guides at all-guides.com FRONT WHEEL AND REAR WHEEL Rear braker caliper 1. Install: Pad support ① Brake pad ② Pad pin ③ 2. Install: Brake caliper ① Right spacer (rear wheel) ② Nut (rear wheel) ③ 5 - 16...
  • Page 127 All manuals and user guides at all-guides.com FRONT WHEEL AND REAR WHEEL Brake master cylinder kit 1. Clean: Brake master cylinder Brake master cylinder kit Clean them with brake fluid. 2. Install: Brake master cylinder cup (primary) ① Brake master cylinder cup (secondary) ② To brake master cylinder piston ③...
  • Page 128 All manuals and user guides at all-guides.com FRONT WHEEL AND REAR WHEEL Front brake master cylinder 1. Install: Brake master cylinder ① Brake master cylinder bracket ② Bolt (brake master cylinder bracket) ③ 9 Nm ( 0.9 m • kg ) NOTE: Install the bracket so that the arrow mark face upward.
  • Page 129 All manuals and user guides at all-guides.com FRONT WHEEL AND REAR WHEEL 9 Nm (0.9 m · kg) Spring ① Brake pedal ② Pin ③ Washer ④ Cotter pin ⑤ NOTE: After installing, check the brake pedal height. Refer to “REAR BRAKE ADJUSTMENT” sec- tion in the CHAPTTER 3 .
  • Page 130 All manuals and user guides at all-guides.com FRONT WHEEL AND REAR WHEEL 2. Install: Copper washer ① Brake hose ② Union bolt ③ 25 Nm (2.5 m · kg) WARNING Always use new copper washers. Rear brake hose 1. Install: Copper washer ①...
  • Page 131 All manuals and user guides at all-guides.com FRONT BRAKE AND REAR BRAKE Brake fluid 1. Fill: Brake fluid Until the fluid level reaches “LOWER” level line . Recommended brake fluid: DOT #3 or DOT #4 WARNING Use only the designated quality brake fluid: otherwise, the rubber seals may deterio- rate, causing leakage and poor brake per-...
  • Page 132 All manuals and user guides at all-guides.com FRONT BRAKE AND REAR BRAKE 4. Install: [Front] Diaphragm Brake master cylinder cap ① Screw (brake master cylinder cap) ② 2 Nm (0.2 m · kg) [Rear] Diaphragm Brake master cylinder cap ① Bolt (brake master cylinder cap) ②...
  • Page 133 All manuals and user guides at all-guides.com STREERING STREERING Order Job / Part name Q’ty Remarks Remove the parts in the order listed. NUT STEERING UPPER M22 WASHER(STEEL). STEERING STEM LOCK NUT BEARING ASSY TRIPLE CLAMP(STEERING STEM) ASSY For installation, reverse the removal procedure. 5 - 23...
  • Page 134 All manuals and user guides at all-guides.com FRONT FORK FRONT FORK Order Job / Part name Q’ty Remarks Remove the parts in the order listed. FRONT NUMBER PLATE FRONT FENDER SCREW SCREW . FRONT.FORK ASSY For installation, reverse the removal procedure. 5 - 24...
  • Page 135 All manuals and user guides at all-guides.com FRONT FORK AND STEERING Installation 1. Install: Front fork ① NOTE: Temporarily tighten the pinch bolts (lower bracket). Do not tighten the pinch bolts (upper bracket) yet. 2. Tighten: Front fork . 4. Tighten: Pinch bolt (upper bracket) ①...
  • Page 136 All manuals and user guides at all-guides.com FRONT FORK AND STEERING REMOVAL POINTS Steering ring nut 1. Remove: Steering ring nut ① Use the steering nut wrench② WARNING Support the steering stem so that it may not fall down. ı Lower bearing 1.
  • Page 137 All manuals and user guides at all-guides.com FRONT FORK AND STEERING Bearing and ball race 1. Wash the bearings and ball races with a solvent. 2. Inspect: Bearing ① Ball race Pitting/damage → Replace bearings and ball races as a set. Install the bearing in the ball races.
  • Page 138 All manuals and user guides at all-guides.com FRONT FORK AND STEERING 4. Install: Steering ring nut ① 30 Nm (3 m · kg) Tighten the steering ring nut using the steering nut wrench Refer to “STEERING HEAD INSPEC- TION AND ADJUSTMENT” section in the CHAPTER 3.
  • Page 139 All manuals and user guides at all-guides.com FRONT FORK AND STEERING 9. Tighten: Pinch bolt (upper bracket) ① 15 Nm (1.5 m · kg) Pinch bolt (lower bracket) 15 Nm (1.5 m · kg) CAUTION: ACHTUNG: Tighten the lower bracket to specified torque.
  • Page 140 All manuals and user guides at all-guides.com HANDLEBAR HANDLEBAR 4 2 5 3 7 6 9 8 Order Job / Part name Q’ty Remarks Remove the parts in the order listed. CROSS BAR COVER CROSS BAR FOAM. GRIP .R THROTTLE HOUSEING THROTTLE CABLE GRIP .L START SWITCH ASSY...
  • Page 141 All manuals and user guides at all-guides.com HANDLEBER REMOVAL POINTS Brake master cylinder 1. Remove: Brake master cylinder bracket ① Brake master cylinder ② CAUTION: ACHTUNG: Do not let the brake master cylinder hang on the brake hose. Keep the brake master cylinder cap side horizontal to prevent air from coming in.
  • Page 142 All manuals and user guides at all-guides.com HANDLEBER ASSEMBLY AND INSTALLATION Handlebar 1. Install: Handlebar ① Handlebar upper holder ② Bolt (handlebar upper holder) ③ 25 Nm (2.5 m · kg) NOTE: The handlebar upper holder should be installed with the punched mark forward.
  • Page 143 All manuals and user guides at all-guides.com HANDLEBER 4. Install: Collar ① Grip cap cover ② Throttle grip ③ NOTE: Apply the lithium soap base grease on the throttle grip sliding surface. 5. Install: Throttle cables ① To tube guide ② . NOTE: Apply the lithium soap base grease on the throttle cable end and tube guide cable wind-...
  • Page 144 All manuals and user guides at all-guides.com HANDLEBER 8. Install: Brake master cylinder ① Brake master cylinder bracket ② Bolt (brake master cylinder bracket) ③ 9 Nm (0.9 m • kg) NOTE: Install the bracket so that the arrow mark faces upward.
  • Page 145 All manuals and user guides at all-guides.com SWINGARM AND REAR SHOCK ABSORBER SWINGARM AND REAR SHOCK ABSORBER Order Job / Part name Q’ty Remarks Remove the parts in the order listed. REAR SHOCK WSHER NEEDLE BEARING BUSHING NEEDLE BEARING MIDDLE AXLE BOLT REAR SWING ARM ASSY CLIP CHAIN GUARD...
  • Page 146 All manuals and user guides at all-guides.com REAR SHOCK ABSORBER AND SWINGARM REMOVING THE REAR SHOCK ABSORBER ASSEMBLY 1. Stand the motorcycle on a level surface. WARNING Securely support the motorcycle so that there is no danger of it falling over. NOTE: Place the motorcycle on a suitable stand so that the rear wheel is elevated.
  • Page 147 All manuals and user guides at all-guides.com REAR SHOCK ABSORBER AND SWINGARM REMOVING THE SWINGARM 1. Stand the motorcycle on a level surface. WARNING Securely support the motorcycle so that there is no danger of it falling over. NOTE: Place the motorcycle on a suitable stand so that the rear wheel is elevated.
  • Page 148 All manuals and user guides at all-guides.com REAR SHOCK ABSORBER AND SWINGARM CHECKING THE REAR SHOCK ABSORBER ASSEMBLY 1. Check: rear shock absorber rod Bends/damage Replace the rear shock absorber assembly. rear shock absorber Gas leaks/oil leaks Replace the rear shock absorber assembly.
  • Page 149 All manuals and user guides at all-guides.com REAR SHOCK ABSORBER AND SWINGARM 4. Check: spacer Damage/wear Replace. bearings Damage/pitting Replace. CHECKING THE DRIVE CHAIN 1. Measure: 10-link section a of the drive chain Out of specification Replace the drive chain. 10-link drive chain section limit (maximum) 144.4 mm...
  • Page 150 All manuals and user guides at all-guides.com REAR SHOCK ABSORBER AND SWINGARM 4. Check: drive chain rollers 1 Damage/wear Replace the drive chain. drive chain side plates 2 Damage/wear Replace the drive chain. Cracks Replace the drive chain and make sure that the battery breather hose is proper- ly routed away from the drive chain and be- low the swingarm.
  • Page 151 All manuals and user guides at all-guides.com REAR SHOCK ABSORBER AND SWINGARM INSTALLING THE SWINGARM 1. Lubricate: bearings spacers pivot shaft Recommended lubricant Molybdenum disulfide grease 2. Install: Swingarm 50 Nm (5.0 m kg) 3. Install rear shock absorber assembly rear wheel Refer to “INSTALLING THE REAR SHOCK ABSORBER...
  • Page 152 All manuals and user guides at all-guides.com REAR SHOCK ABSORBER AND SWINGARM CAUTION: A drive chain that is too tight will overload the engine and other vital parts, and one that is too loose can skip and damage the swin- garm or cause an accident.
  • Page 153 All manuals and user guides at all-guides.com ELECTRICAL COMPONENTS AND WIRING DIAGRAM ELECTRICAL ELECTRICAL COMPONENTS AND WIRING DIAGRAM ELECTRICAL COMPONENTS Starter Solenoid Rectifier/Regulator CDI magneto Spark plug Ignition coil CDI unit WIRING DIAGRAM 6 - 1...
  • Page 154 All manuals and user guides at all-guides.com IGNITION SYSTEM IGNITION SYSTEM INSPECTION STEPS Use the following steps for checking the possibility of the malfunctioning engine being attributable to ignition system failure and for checking the spark plug which will not spark. Spark *Clean or replace Spark gap test...
  • Page 155 All manuals and user guides at all-guides.com IGNITION SYSTEM SPARK GAP TEST 1. Disconnect the spark plug cap from spark plug. 2. Remove the ignition coil cap. 3. Connect the dynamic spark tester① (ignition checker② ) as shown. Ignition coil③ Spark plug④...
  • Page 156 All manuals and user guides at all-guides.com IGNITION SYSTEM 2. Inspect: Engine start switch conduct Tester (+) lead → Red/Yellow lead Tester (–) lead → Black lead Tester selec- tor position PUSH IN Ω × 1 FREE No continuous while being pushed → Replace. Continuous while being freed →...