Subscribe to Our Youtube Channel
Related Manuals for Posch LogFix 30
Summary of Contents for Posch LogFix 30
- Page 1 Operating Instructions LogFix 30 D1010559-V001 English Copyright by Posch Gesellschaft m.b. H., Made in Austria...
- Page 2 Machine number:................Serial number:..................POSCH Austria: 8430 Leibnitz, Paul-Anton-Keller-Strasse 40, telephone: +43 (0) 3452/82954, fax: +43 (0) 3452/82954-53, e-mail: leibnitz@posch.com POSCH Germany: 84149 Velden/Vils, Preysingallee 19, telephone: +49 (0) 8742/2081, fax: +49 (0) 8742/2083, e-mail: velden@posch.com D1010559-V001...
-
Page 3: Table Of Contents
English Contents Contents 1 Foreword ............................. 1.1 Copyright notice .......................... 1.2 Liability for defects ........................1.3 Reservations ..........................1.4 Definitions ........................... 1.5 Operating instructions ......................... 2 Safety information ..........................2.1 Explanation of symbols ....................... 2.2 General safety information ......................Safety information (conveyor belts)..................... Safety information (rope winches).................... - Page 4 Contents English 11.3 Cleaning ............................28 12 Special equipment..........................29 12.1 Radio remote control........................29 12.2 Conveyor belt ..........................31 12.3 Hopper for refilling........................37 13 Accessories ............................38 13.1 Chute extension .......................... 38 13.2 Chassis ............................39 14 Troubleshooting........................... 40 14.1 Disposal ............................
-
Page 5: Foreword
English Foreword | 1 1 Foreword Thank you for buying our product. This machine has been built in conformity with applicable European standards and regula- tions. These operating instructions explain how to operate the machine safely and efficiently and how to maintain it. Any person entrusted with the transport, installation, commissioning, operation or mainten- ance of the machine must have read and understood: •... -
Page 6: Operating Instructions
1 | Foreword English The operating personnel (operators) are those entrusted by the operator to operate the ma- chine. Technical personnel Technical personnel are persons entrusted by the operator of the machine with special tasks such as installation, set-up, maintenance and troubleshooting. Electrician An electrician is a person who, by virtue of his specialist training, has knowledge of electrical systems, standards and regulations and is able to identify and prevent possible hazards. -
Page 7: Safety Information
English Safety information | 2 2 Safety information 2.1 Explanation of symbols The following symbols and instructions in this manual provide warnings about possible per- sonal injury or property damage or give useful information about working with the machine. Warning about danger zones Instruction regarding safe working, where non-compliance entails the risk of serious or fatal injury. -
Page 8: General Safety Information
2 | Safety information English Wear protective gloves Wear safety shoes Instruction Symbol for proper use of the machine. Non-compliance can result in malfunctions or damage to the machine. Further information Symbol for further information relating to a bought-in part. Information Action-related information. -
Page 9: Safety Information (Conveyor Belts)
Never leave the machine running unattended. Switch off the machine's drive unit before carrying out any adjustments. Only use original - POSCH - spare parts. Do not modify or tamper with the machine. Work on electrical equipment must only be carried out by qualified electricians. -
Page 10: Noise
It is up to the operating personnel to ensure that work is carried out safely. 2.5 Proper use The LogFix 30 machine is designed exclusively for filtering firewood with a maximum length of 50 cm. Proper use also includes adherence to the prescribed operating, inspection, maintenance and servicing conditions and particular attention should also be paid to the safety instructions contained in the user manual. -
Page 11: General
F0004723 Chassis for transfer 3.2 Description The LogFix 30 is used to filter firewood billets. The firewood filter reliably removes contaminants, such as loose chips, bark or pieces of wood, from split and cut billets. This firewood filter can be used with any machine that has a conveyor belt. -
Page 12: The Most Important Components Of The Machine
3 | General English 3.3 The most important components of the machine Rollers Base frame Trough Main pillar Geared motor Rating plate Lubricating bar Hopper Switch with plug Mounting for forklift D1010559-V001... -
Page 13: Stickers And Their Meaning
English General | 3 3.4 Stickers and their meaning Danger zone Z2001246 Always read the user manual before operating the machine Z2040010 Lift here Z2001084 Rotational direction of motor Z2001220 Lifting point for forklift Z2001311 Lubrication point Z2050400 Phase inverter Z205 0010 D1010559-V001... -
Page 14: Set-Up
4 | Set-up English 4 Set-up Ensure the machine is stable before starting it. Set up the machine on a horizontal, level, firm and clear work surface. The machine must be placed directly on the ground. Do not place wooden boards, flat pieces of metal, etc. - Page 15 English Set-up | 4 • Place a metal basket or similar under the billet screen to catch the chips or waste. Ensure that the extraction zone is secure (affix access guard, e.g. using a safety grille). D1010559-V001...
-
Page 16: Controls And Functions
5 | Controls and functions English 5 Controls and functions 5.1 Adjustable swivel Lifting gear Locking tab (2x) Lifting eye Top frame Clip pin (2x) The swivel of the firewood filter can be adjusted from 0–10°. Adjusting: • Lift the top frame a little using a lifting gear. Only lifting gear with the permitted load capacity may be used. -
Page 17: Electrical Functions
English Controls and functions | 5 5.2 Electrical functions Switchgear cabinet The switchgear cabinet for the option RC is shown on the right. CEE plug Emergency stop button Button (red) – automatic stop Indicator lamp (red) – fault Button (arrow pointing downwards) – Button (arrow to the left) –... - Page 18 5 | Controls and functions English Automatic system In the event of a blockage, the rollers move backwards for approx. 3 seconds and then for- wards again. If a blockage should also occur when moving backwards, the rollers move forwards again for approx.
-
Page 19: Start-Up
English Start-up | 6 6 Start-up Check the machine for potential damage prior to every use. • When doing so, pay particular attention to inspection activities in section "Checks [} 25]". Before starting to operate the machine, please check that the protective and safety systems are working. - Page 20 6 | Start-up English A tight plug connection can rip the CEE plug out of the switch housing. • This can be remedied using standard plugs and a silicone spray. Any such damage to the switch is not covered by the guarantee. Control voltage The machine is operated using the green button on the control unit.
-
Page 21: Work Operation
English Work operation | 7 7 Work operation Only one person may operate the machine at a time. Ensure that no other people are near the machine. 7.1 Filtering process Conveyor belt Rollers • Set up the billet screen such that it is aligned with the splitter or its conveyor belt. •... -
Page 22: Put Out Of Operation
8 | Put out of operation English 8 Put out of operation 8.1 Put drives out of operation Driven by electric motor (Type E) Type E2.2 Diagram – analogous Green button (ON) Red button (OFF) • Press the red button. All E types Disconnect the machine from the power supply when it has come to a standstill: Pull out the plug of the device (mains plug). -
Page 23: Transport
English Transport | 9 9 Transport Before transportation, it is vital that the drive is switched off and secured to ensure that it cannot be switched on accidentally or started up by unauthorised persons. Disconnect the machine from the power supply when it has come to a standstill: Pull out the plug of the device (mains plug). -
Page 24: Lifting With A Crane
9 | Transport English 9.2 Lifting with a crane Lifting gear Lifting eye When using a crane, only lift the machine by the lifting eyes. Only lifting gear with the permitted load capacity may be used. D1010559-V001... -
Page 25: Checks
English Checks | 10 10 Checks Before carrying out checks on the machine, it is absolutely essential to switch off the drive unit and to ensure that it cannot be switched on accidentally or started up by unauthorised persons. Disconnect the machine from the power supply when it has come to a standstill: Pull out the plug of the device (mains plug). - Page 26 10 | Checks English • Visual inspection of correct condition • Function test • Where appropriate, test of the earth conductor and measurement of the earth conductor current • Where appropriate, measurement of the insulation resistance. Work on electrical equipment must only be carried out by qualified electricians. D1010559-V001...
-
Page 27: Maintenance
Work on electrical equipment must only be carried out by qualified electricians. Never work without the protective guards in place. Only use original - POSCH - spare parts. 11.1 Lubrication Dispose of oily and greasy parts and oil residues in accordance with legal regulations. -
Page 28: Oil Changing
11 | Maintenance English The lubrication points are marked with the lubricate symbol. Recommended lubricating greases: Manufacturer Type Genol Multi-purpose grease Fuchs Multi-purpose grease 5028 11.2 Oil changing Old oil must be disposed of in an environment-friendly manner. Find out about the environ- mental regulations in your country. -
Page 29: Special Equipment
English Special equipment | 12 12 Special equipment 12.1 Radio remote control Safety information: Familiarise yourself with the functions before using radio remote control. Only authorised persons who have received relevant training are permitted to operate the machine by radio remote control. Operation: O F F S T A... - Page 30 12 | Special equipment English • Undo the screws on the cover. • Remove the cover. • Remove the old batteries. • Insert the new batteries. Required batteries: 3 alkaline "AAA" 1.5 V Ensure the correct polarity! • Refit the cover and screw it tight. D1010559-V001...
-
Page 31: Conveyor Belt
English Special equipment | 12 12.2 Conveyor belt Keep clear of the danger zone! • See ..Stickers on belt conveyor 12.2.1 Conveyor belt types Conveyor belt type Conveyor belt length Conveyor height Belt width 300 cm up to 350 cm 40 cm 500 cm up to 450 cm... - Page 32 12 | Special equipment English Conveyor belt Permissible swivel range Rope winch Locking lever Swivel indicator Conveyor belt angle • Crank the conveyor belt to the desired height using the rope winch. Observe the conveyor belt angle! The angle of the conveyor belt may not exceed 35° otherwise the conveyor belt will be des- troyed by the split logs.
- Page 33 English Special equipment | 12 On conveyor belt type SF5: Transport plate Pulley unit Upper conveyor belt frame Tension strut Safety chain Connecting link Fixing hook • Remove both of the transport plates. – Keep these for transport in the future. •...
- Page 34 12 | Special equipment English Hydraulically pivoting conveyor belt O F F S T A S T O A ..Variant 1, B ..Variant 2 Button (arrow to the right) – pivot con- Button (arrow to the left) – pivot con- veyor belt right veyor belt left The conveyor belt can be pivoted easily using the hydraulic pivot function.
- Page 35 English Special equipment | 12 12.2.3 Maintenance - conveyor belt Conveyor belt instructions The conveyor belt may become slack over time as a result of wear and tear. If this happens, the belt must be retensioned. Check that the belt is running centrally. The belt drive dogs must not move. •...
- Page 36 12 | Special equipment English Lubrication schedule – conveyor belt Lubrication interval Item Where What Quantity Monthly (every 160 Conveyor belt, 4 lub- Housing bearings, top and operating hours – or rication nipples bottom on both sides more frequently de- Pivot cylinder, 2 lub- Bearing eyes, on both sides pending on use)
-
Page 37: Hopper For Refilling
English Special equipment | 12 12.3 Hopper for refilling Hopper for refilling Hopper for 3-sided refilling with the dimensions 240 x 240 cm. D1010559-V001... -
Page 38: Accessories
13 | Accessories English 13 Accessories 13.1 Chute extension Note: cannot be combined with option SF3 Chute extension Lock washer (14x) Trough Locking nut (7x) Hexagon bolt (7x) Chute extension 75 cm for a transfer height of 15–145 cm. Mounting: •... -
Page 39: Chassis
English Accessories | 13 13.2 Chassis Main pillar Locking nut (6x) Axle Wheel (2x) Hexagon bolt (6x) Wheel nut (10x) Lock washer (12x) Chassis for easy transfer of the machine (e.g. using a forklift truck) on level ground. Mounting: • Shorten the main pillar according to the half wheel diameter. See .. -
Page 40: Troubleshooting
14 | Troubleshooting English 14 Troubleshooting Before rectifying faults on the machine, it is vital that the drive is switched off and secured to ensure that it cannot be switched on accidentally or started up by unauthorised persons. Disconnect the machine from the power supply when it has come to a standstill: Pull out the plug of the device (mains plug). -
Page 41: Technical Data
English Technical data | 15 15 Technical data Type E2.2–400 Drive Drive type Electric motor Output 2.2 S6 ** Voltage Fusing Filling drum Diameter Height Max. log length Fill amount lcm *** Dimensions * Length Width Height Weight 1390 *..the dimensions and weights (rounded) stated are guide figures and apply to the basic model; these can differ considerably for the different models. The ac- tual weight is specified on the rating plate. -
Page 42: Service
16 | Service English 16 Service POSCH- Product To order spare parts or a service for your machine please contact your local dealer directly. If you require a spare parts list for your machine, you can download this at any time by entering the serial number at the following link: https://www.posch.com/en/service/download/... -
Page 43: Ec Declaration Of Conformity
What is more, the machine complies with the EC Electromagnetic Compatibility (EMC) Dir- ective 2014/30/EU. This Declaration is not valid for any modifications to the machine which are not approved by Firewood filter - LogFix 30 Item no.: M8030 Model: Option RC, SF3, SF5, H, T Serial no.:... - Page 44 Your Posch Dealer...
Need help?
Do you have a question about the LogFix 30 and is the answer not in the manual?
Questions and answers