Advertisement
UNPACKING AND SET-UP INSTRUCTIONS
Unpack your heater and remove the wheel assemblies from the package. Refer to Fig. 1
below:
1.
Make sure the heater is unplugged and in
the "OFF" position.
2.
TURN THE HEATER UPSIDE DOWN.
3.
Position the wheel base assemblies
between the end fins as shown.
4.
Insert each U-shape screw into the holes
of each wheel holding plate.
5.
Insert the butterfly nuts and screw them
tightly.
6.
Turn the heater upright.
Your heater is now ready for use.
CAUTION: Risk of fire – Do not operate heater without wheel assemblies attached. Operate
heater in upright position only (wheels on bottom, controls on top). Any other position could
create a hazardous situation.
OPERATING INSTRUCTIONS
IMPORTANT!
Your heater is equipped
with a polarized alternating
current line plug (a plug
having one blade wider
than the other). This plug
will fit into the power outlet
only one way. This is a
safety feature. If you are
unable to insert the plug
fully into the outlet, try
reversing the plug. If the
plug should still fail to fit,
contact your electrician to
replace your outlet. DO
NOT defeat the safety
purpose of the polarized
plug.
Control Panel Functions
A
Power Indicator Light
C
Caution Indicator Light
Fig. 1 - Upside down view
Wheel
holding
plate
Carry Handle
A
C
D
B
Cord Wrap
B
Power and Setting Control
D
Thermostat Control
Place the heater on a firm level surface free from obstructions, and at least
•
3ft.away from any wall and any other objects such as furniture, curtains, plants or
combustible material.
With the Power and Setting Control " B " in the " OFF " position, plug the heater
•
into a grounded 120V outlet.
Turn the heater "ON" by turning the Power and Setting control " B " clockwise
•
to your desired power setting (LOW, MED, HIGH). The Power Indicator Light
U-shape
"A" will illuminate.
screw
Turn the Thermostat Control " D " to your desired setting from "MIN" to "MAX".
•
Setting for Optimum Comfort: When the room reaches a comfortable temperature,
slowly turn the Thermostat Control "D" counter-clockwise until the heater turns off.
This is the point at which the thermostat setting equals the room temperature. At this
setting, the thermostat will automatically turn the heater on and off to maintain this
selected temperature.
CAUTION: This heater includes an Overheat Protection System that shuts the unit off
if it overheats due to abnormal conditions. At this time, the "C" Caution Indicator
Light gets on. If this occurs turn the heater "OFF", unplug it, and inspect and remove
any objects on or adjacent to the heater. Allow it to cool for a few minutes, plug it back
in, and resume normal operation.
ADDITIONAL FEATURES
This heater has additional features:
Cord Wrap-Neatly stores power cord when the heater is not used.
•
Convenient Carry Handle and Heavy-Duty Caster Wheels-Allow for easy
•
maneuvering from room to room.
TROUBLESHOOTING
If your heater fails to operate, please follow these instructions:
Ensure that your circuit breaker or fuse is working properly.
•
Be sure the heater is plugged in and that the electrical outlet is working properly.
•
Check for any obstruction. If you find any obstruction, turn the heater "OFF".
•
Unplug the heater and wait a few minutes for it to cool down. Carefully remove
Carster Wheels
the obstruction. Plug the heater in and turn it on again by referring to the
OPERATING INSTRUCTIONS.
NOTE: IF YOU EXPERIENCE A PROBLEM WITH YOUR HEATER, PLEASE SEE THE
WARRANTY INFORMATION FOR INSTRUCTIONS. PLEASE DO NOT ATTEMPT TO
OPEN OR REPAIR THE HEATER YOURSELF. DOING SO MAY VOID THE WARRANTY
AND COULD CAUSE DAMAGE OR PERSONAL INJURY. IF THE PROBLEM STILL
PERSISTS, PLEASE CONTACT US BY REFERRING TO THE SERVICE & SUPPORT
INFORMATION ON THE FOLLOWING PAGE.
Advertisement
