Advertisement
RE AR STO R AGE B OX
UN1 10 5B
INSTALLATION
GUIDE
F L AT L I N E VA N C O • S U P P O R T @ F L AT L I N EVA N C O . C O M • 8 8 8 - 6 6 7- 5 5 7 6
TOOLS REQUIRED
(NOT INCLUDED)
+
9/16" WRENCH
+
RATCHET
+
3/8" SOCKET
+
MEASURING TAPE
+
10MM WRENCH
+
MARKER
+
13MM WRENCH
+
9/16" SOCKET
+
5MM ALLEN WRENCH
INSTALL INFO
TIME TO INSTALL THIS PRODUCT: 1 HOUR
Additional help is suggested for a few of the install steps.
Compatible with all FVC Rear Door Platforms.
BEFORE YOU START
Please inspect the product and packaging upon
delivery to ensure there are no issues and that
all parts and hardware are accounted for.
Contact us ASAP if anything is missing at:
support@flatlinevanco.com
0 1
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for FVC UN1105B
Summary of Contents for FVC UN1105B
- Page 1 INSTALL INFO TIME TO INSTALL THIS PRODUCT: 1 HOUR Additional help is suggested for a few of the install steps. Compatible with all FVC Rear Door Platforms. BEFORE YOU START Please inspect the product and packaging upon delivery to ensure there are no issues and that all parts and hardware are accounted for.
-
Page 2: Before You Start
BEFORE YOU START All Flatline Van Co products must be properly assembled and secured before attaching to your vehicle. Improper attachment could result in an automobile accident, and could cause serious bodily injury or death to you or to others involved. You are responsible for assembling and securing Flatline Van Co products to your vehicle, checking the mounting points and attachments prior to use, and regularly inspecting the products for wear and or damage. -
Page 3: Package Contents
PACKAGE CONTENTS REAR STORAGE BOX QTY: 1 F L AT L I N E VA N C O • S U P P O R T @ F L AT L I N EVA N C O . C O M • 8 8 8 - 6 6 7- 5 5 7 6... - Page 4 HARDWARE 3/8-16 X 1.25 FLANGED HEX 3/8 BONDED 3/8-16 NYLON INSERT HEAD SCREW 3/8 SCREW FLAT WASHER SEALING WASHER LOCKNUT QTY: 4 QTY: 4 QTY: 4 QTY: 4 DRAIN PLUG QTY: 2 F L AT L I N E VA N C O • S U P P O R T @ F L AT L I N EVA N C O . C O M • 8 8 8 - 6 6 7- 5 5 7 6...
- Page 5 If you’d rather measure, see FIG 2 for distances between the mounting points. 1.2 If you are using a product other than the FVC Rear Door Platform, mark the back of the box to match your available F I G 1 mounting points and drill out (4) 3/8”...
- Page 6 RATCHET TOOLS REQUIRED FOR THIS STEP: 9/16” SOCKET 9/16” WRENCH STEP | 02 BOX TO PLATFORM INSTALL 2.1 Open the top door of the box to access the upper mounting holes. 2.2 Insert (1ea) 3 ⁄ 8-16 x 1.25” Flanged Hex Head Screws and 3 ⁄...
-
Page 7: Step | 03 Door Adjustments
TOOLS REQUIRED FOR THIS STEP: 13MM WRENCH 10MM WRENCH STEP | 03 DOOR ADJUSTMENTS [AS NEEDED] LOWER DOOR HEIGHT UPPER DOOR HEIGHT 3.1 The upper door height can be adjusted by moving the strut from the factory location to the secondary location as shown in FIG 7. - Page 8 10MM WRENCH TOOLS REQUIRED FOR THIS STEP: 5MM ALLEN WRENCH STEP | 03 DOOR ADJUSTMENTS [AS NEEDED] JAM NUT BUTTON LATCH 3.4 Using two 10MM Wrenches, loosen the Ball Stud and adjust BALL STUD as needed. Tighten Jam Nuts and verify adjustment by closing the door.
-
Page 9: Step | 04 Shelf Adjustment
3/8” SOCKET TOOLS REQUIRED FOR THIS STEP: STEP | 04 SHELF ADJUSTMENT [OPTIONAL] 4.1 Use a 3 ⁄ 8” Socket to remove factory-mounted shelf hard- ware. HOLDING SLOT 4.2 Adjust to desired height. The shelf is adjustable in 1” increments. 4.3 Set in place using middle holding slots and two 1/4-20 Hex Bolts. - Page 10 FVC (and see) from you! Head to the products and following along and we will make it right. FVC is product page and click “Leave a company of van and outdoor with your adventures. Tag us Review.”...
Need help?
Do you have a question about the UN1105B and is the answer not in the manual?
Questions and answers