Yamaha DX9 Operating Manual page 35

3.HOW ТО PLAY PRE-PROGRAMMED VOICES
€ Playing the Internal Voices
The DX9 has 20 internal voices, any one of which can be
selected simply by pressing the key,
and then by pressing the appropriate Voice Select key.
Each Voice Select key has a large numeral that corresponds
to the voice number at its left edge.
Select and play each voice to get a feel for the kind of
sounds that are available.
EDIT/ MEMORY
COMPARE SELECT
ШЕШ | Press the Memory Select key,
C P \ ] set to the Play mode.
гај
Select the
preset voice voice number
€ Playing the External Voices
The voice data contained on the voice data cassette must be
loaded into the instrument before it can be played.
Two types of LOAD functions are provided: LOAD, with
which an entire group of 20 voices is loaded, and LOAD
SINGLE, with which any desired single voice can be loaded.
. 1} LOADing an entire 20-voice group.
(1) Make sure the cassette recorder is properly connect-
ed to the DX9, insert the cassette containing the desired
voice group, and set the tape to the beginning of that
voice group (disengage the remote control function to
do this). Stop the cassette recorder.
(2) Turn MEMORY PROTECT OFF.
zi)
PROTEO) so
-1
AS
FUNCTION CONTROL
MEM. PROTECT: OFF
(3) Press the key and then the key and
the display will read "from TAPE to MEM all ready?"
(the remote control function is re-engaged).
(4) Make sure the cassette recorder's headphone jack is
connected to the DX9 and press the cassette recorder
PLAY button.
(5) Press the key and the "ready?" portion of the
display will disappear, the tape will begin to run, and the
pilot tone will be heard.
(6) Adjust the cassette recorder volume control to set
the pilot tone at a comfortable listening level.
(7) When the data signal begins the bottom right hand
corner of the display will read "'1'* through "20" as the
corresponding voices are loaded into the internal memory.
from TAPE to MEM
all 1--
Display will read
"1" through "20"
(8) When the LOAD operation is completed the DX9
PLAY mode will be engaged and the cassette recorder
will stop.
* Using a Cassette Recorder with No REMOTE Terminal
The SAVE and LOAD procedures are basically same for
cassette recorders with or without a REMOTE terminal.
When there is no REMOTE terminal, the cassette recorder
must manually be set to the record or play mode after the
or and keys have been pressed
("теаду 2" display).
2) LOADing a single voice.
This function loads any single voice from within a voice
group, and operates basically in the same way as for
loading a voice group. Instead of pressing the
key, press the key.
(1) Make sure the cassette recorder is properly connect-
ed and set the tape to the beginning of the voice group
that contains the desired voice.
(2) Press the key and then the
key and the display will read "from ТАРЕ to BUF
single? (1—20}". The DX9 is asking you for the number
of the desired voice.
(3) Press the preset key corresponding to the number of
the desired voice and the display will respond with the
chosen voice number and "ready?"'.
| from ТАРЕ ta
Поб са Presno single 18 res
voice number
(4) Press the [YES ]key and the tape will begin playback.
The pilot tone will be heard.
(5) Set the cassette recorder volume control so that the
pilot tone is at a comfortable listening level.
(6) The display counts down the voices in the group, and
the DX9 PLAY mode is engaged when the desired voice
has been loaded. The voice number display shows "07,
The loaded voice must then be stored in any preset
number according to the STORE instructions in your
Owner's manual.
YAMAHA
OMD-73A] 83113 @ Printed in Japan