Important safety instructions Preliminary steps Scrapping Declaration of conformity CE Built-in installation Product description Technical data Using the appliance for the first time Switching on and preheating Making coffee (using coffee beans) Changing the amount of coffee in the cup Adjusting the coffee grinder Making espresso with pre-ground coffee (instead of beans) Running off hot water...
Important safety instructions The appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety. Children should be supervised to ensure that they do not play with the appliance.
Page 7
Critical safety warnings This appliance is designed exclusively for domestic use. WARNING: • It is not designed or approved for use in: - areas appointed as staff kitchens in shops, offices or other working environments - agritourism establishments - hotels, motels and other hospitality structures - rooms for rent •...
Preliminary steps Transport check After unpacking the appliance, check that it is undamaged and that all the accessories are present and correct. Do not use the appliance is there is any visible damage. Contact the After-sales Service. Installing the appliance Critical safety warnings WARNING: •...
Built-in installation Check the minimum measurements required for correct installation of the appliance. The coffee machine must be installed in a column unit, which must in turn be securely fixed to the wall by means of commercial brackets. Attention: • Disconnect the appliance from the mains before carrying out any installation work or servicing. •...
Page 10
Secure the power supply cable with the clip provided. The power supply cable must be long enough to allow the machine to be removed from the housing in order to fill the coffee bean container. Regulations require that the appliance is earthed. Electrical connection must be carried out by a qualified electrician in accordance with the manufacturer’s instructions.
Product description Appliance Control panel See image A on page 2. See image B on page 2. Cup tray N.B.: the touch-control buttons are activated at the lightest touch of a finger. Service door Coffee feed Display: guides the user through use of the machine.
Using the appliance for the first time • Coffee has been used to factory test the machine and it is therefore completely normal for there to be traces of coffee in the mill. • Customize water hardness as soon as possible, following the instructions in paragraph Setting water hardness.
Making coffee (using coffee beans) 1. The machine is factory-set to make coffee with a standard taste. You can choose coffee with the following tastes: extra-mild, mild, standard, strong or extra-strong, with the option of using pre-ground coffee. To choose the desired taste, press the button (B3) (Figure 8) repeatedly until the required taste is displayed.
Changing the amount of coffee in the cup The appliance is factory-set to automatically deliver the following amounts of coffee: • Espresso, • Small cup, • Medium cup, • Large cup, • Mug. To modify these quantities and set the amount of coffee desired, for example changing the amount of espresso, proceed as follows: •...
Running off hot water • Always check that the machine is ready for use. • Check that the water spout is attached to the nozzle (Figure 6). • Place a container under the spout. • Press button (B11) the display will show HOT WATER PRESS OK , press (B7) to confirm.
N.B.: • While making cappuccino, you can stop frothed milk or coffee run-off by pressing the button (B10). • To keep the milk frother hygienically clean at all times, always clean the internal tubes of the milk container lid after making cappuccino. The message PRESS CLEAN BUTTON is displayed: - place a container under the milk spout (Figure 25);...
Page 17
Setting the language To change the display language, proceed as follows: • Press the MENU button (B2) to access the menu and then buttons (B5) and (B6) to select LANGUAGE . • Press (B7). • Press buttons (B5) and (B6) until the required language is displayed. •...
Page 18
Setting water hardness If desired, the interval between descaling cycles can be increased so that descaling is performed less frequently and in accordance with the actual calcium content of the water used. Proceed as follows: • Remove the “Total hardness test” water hardness strip from its packaging (attached to page 2), immerse it fully in the water for a few seconds.
(B7) DISABLE? is displayed (or ENABLE? if the function has already been disabled). • Press the icon • Press the icon (B7) to enable or disable the function or the icon (B2) to exit the menu. Statistics This function enables you to view the machine statistics. To view them, proceed as follows: •...
Page 20
The drip tray has a water level indicator in the form of a red float (Figure 27). Empty and clean the drip tray before the red float protrudes from the cup tray. To remove the drip tray: 1. Open the service door (Figure 16). 2.
N.B.: If you encounter difficulty inserting the brewing unit, before inserting it adapt it to the right size by pressing it forcefully from both the bottom and top simultaneously as shown in the figure. 7. Once inserted, make sure the two red buttons have clicked out. 8.
Displayed messages DISPLAYED MESSAGE POSSIBLE CAUSE REMEDY - The water tank is empty or - Fill the tank with water and/or insert it FILL TANK ! incorrectly positioned. correctly, pushing it as far as it will go. GROUND TOO FINE ADJUST MILL ! - The ground is too fine so the - Turn the grinding adjustment knob...
Troubleshooting Below is a list of some possible malfunctions. If the problem cannot be resolved as described, contact After-sales Service. PROBLEM POSSIBLE CAUSE REMEDY The coffee is not hot. - The cups have not been pre-heated. - Heat the cups by rinsing them with hot water. - The brewing unit has cooled down - Before making coffee, heat the brewing unit by because 2/3 minutes have elapsed since...
Page 24
Printed in Italy 02/2016 4000 108 67024...
Need help?
Do you have a question about the CM 9945 H and is the answer not in the manual?
Questions and answers