2. PRECAUTIONS AND NOTICES 2-1 SAFETY PRECAUTIONS 1. Observe all caution and safety related notes located inside the display cabinet. 2. Operation of the display with the cover removed, may cause a serious shock hazard from the display power supply. Work on the display should not be attempted by anyone who is not thoroughly familiar with precautions necessary when working on high voltage equipment.
HIGH VOLTAGE WARNING Operation of monitor outside of cabinet or with back removed may cause a serious shock hazard. Work on this model should only be performed by those who are thoroughly familiar with precautions necessary when working on high voltage equipment.
PIN NO. DESCRIPTION PIN NO. DESCRIPTION GREEN BLUE SYNC. GND HORIZ. SYNC GND-R VERT. SYNC (•VCLK) GND-G GND-B 3. Apply power to the display by turning the power switch to the "ON" position and allow about thirty seconds for display tube warm-up.
Page 8
2. Factory preset Timings Adjustment: A. Press shuttle Knob to show OSD window press shuttle Knob again to switch the functional controls. B. Rotate the shuttle Knob to select the "ZOOM" function, then press the shuttle Knob 10 seconds again. While do not release the shuttle Knob until the OSD window changed to the Factory preset window.
Page 9
G. The setting data of the CONTRAST, BRIGHTNESS, PIN-BALANCE, PARALLELOGRAM, ROTATION, COLOR TEMPERATURE are common mode saved in the memory. Don't needed adjust it individual at every timing Mode and save in the memory. 3. White Balance, Luminance adjustment: A. Bias (Low Luminance) adjustment: (a) Set mode 7 1024 x 768 Fh: 60KHz full white pattern.
Page 10
5. Purity Adjustment: A. Be sure that the display is not being exposed to any external magnetic fields.. B. Ensure that the spacing between the Purity, Convergence, Magnet, (PCM), assembly and the CRT stem is 29mm .(See below diagram) C. Produce a complete, red pattern on the display. Adjust the purity magnet rings on the PCM assembly to obtain a complete field of the color red.
5. CIRCUIT DESCRIPTION 5-1 MICRO CONTROLLER CIRCUIT MICRO Controller The IC101 contains a 6502 8-bit CPU code, 256 bytes of RAM, 16K bytes of ROM, 14 channel 8 bit PWM D/A converters, 2 channel A/D converters for key detection, one 8 bit pre-laudable base timer, internal H-sync and V-sync signals processor providing mode detection, watch- dog timer preventing system from abnormal operation, and an I2C bus interface.
5-2 DEFLECTION CIRCUIT Hor. Sync. And Ver. Sync come from PC, then go into the CPU (IC101). The output Sync Flows into Auto sync Deflection Controller IC401 (TDA4856). The IC401 processes Sync Signal and output drive signal to horizontal, vertical and B+ driver circuit.
5-5 TRANSISTOR & DIODE CIRCUIT LOCATION FUNCTIONAL DESCRIPTION D101 For C102 Discharge Q101 For LED indicator control D418 Protection Diode for Snubber Clip Diode ZD401 D431 Protection diode for B+ control D405, D424 Protection diode for Q403 D406, D407 Supply a bias for D408 D408 Demping diode D421~D423...
Page 14
LOCATION FUNCTIONAL DESCRIPTION D921~D923 Rectifier for output Voltage Supply D924 Clip Diode for Trigger CKT D925 Rectifier for B+ Supply D926,D927 Raster Position Control D939 Clip Diode for Snuffer Pulse ZD901,ZD902,ZD903 Protection Diode Q901 MOS FET for Switching Power Control Q904,Q906 Start up CKT for IC901 Q908,Q916...
6.TROUBLE SHOOTING CHART 6-1 NO RASTER, CRT RELATIVE CIRCUIT PROBLEMS CHECK MAIN PCB POWER SUPPLY 60.5V,14.5V,80V CHECK POWER SAVING CIRCUIT, H-SYNC, V-SYNC SIGNAL CHECK THE HIGE VOLTAGE REFER ITEM S.M.P.S. OF CRT ABOUT 25.5 ~ 26.5KV CHECK FAILSAFE CKT IC401 PIN 2 RELATIVE CKT.
6-2 ABNORMAL DISPLAY NO SIGNAL ON SCREEN CHECK VIDEO IC801 VCC ABOUT 12V CHECK THE PIN 2 OF P802 CONNECTOR = 12V CHECK THE OUTPUT VOLTAGE OF IC701 PIN 18, 20, 23 ABOUT 3Vpp CHECK THE RELATIVE CIRCUIT OF IC801 CHECK THE B+ VOLTAGE OF VIDEO PCB ABOUT 80V CHECK THE 80V RELATIVE CIRCUIT...
6-9 POOR FOCUS READJUST FOCUS CONTROL CHECK FOCUS CONTROL UNIT,FOCUS LEAD WIRE, CRT SOCKET & CRT 6-10 NO SOUND (OPTION FOR AUDIO MODEL ONLY) ADJUST VOLUME CONTROL CHECK IC501 PIN 14 ABOUT 14V CHECK POWER ENSURE THE SOUND SOURCE SUPPLY CIRCUIT IS POWER ON CHECK IC501 IC501 FAILURE...
6-12 POWER SUPPLY TROUBLE SHOOTING CHART BEFORE CHECK SW.REG. PLEASE REFER TO THE POWER SUPPLY BLOCK DIAGRAM POWER SUPPLY OUTPUT: (A) VARIABLE OUTPUT : 60V - 186V (DEPENDING UPON H.SYNC FREQUENCY) (B) CONSTANT OUTPUT : 7V, 20V, 29V, 54V, 80V BEAD SET ABNORMAL VARIABLE OUTPUT CHECK AC LINE...
Page 22
PARTS LIST OF CABINET LOCATION PARTS No. SPECIFICATION CM995TYM CHASSIS FOR S995T IIYAMA 503- SCREW RUBBER WASHER 115- F.B.T CLIP 112- WIRE MOUNT 381- RUBBER FOOT 403- STEEL 506- SPRING 33A 3663- SUPPORT 33A 3726- POWER CAP 33A 3727- POWER ROD 33A 3766- POWER LED LENS 33A 4064-...
Page 23
PARTS LIST OF CHASSIS LOCATION PARTS No. SPECIFICATION AIM995TYM MAIN BOARD CR995TYM CRT BOARD ASS'Y 421- SCREW 202- STAINLESS STEEL CLIP 127- PC SUPPORT 5640- AL GND LUG 5659- 500 - REAR BRACKET 581- 26 - CHASSIS LABEL 581- 26 - FAIL-SAFE LABEL 500- CABLE TIE...
Page 29
J076 TIN COATED J077 TIN COATED J078 TIN COATED J079 TIN COATED J080 TIN COATED J081 TIN COATED J082 TIN COATED J083 TIN COATED J084 TIN COATED J085 TIN COATED J086 TIN COATED J087 TIN COATED J088 TIN COATED J089 TIN COATED J090 TIN COATED...
Page 30
J165 TIN COATED J166 TIN COATED J167 TIN COATED J168 TIN COATED J170 TIN COATED J171 TIN COATED J173 TIN COATED L101 339 - 3.3UH +-10% RF Coated Choke Coil L102 221 - 220UH +-10% Q101 420- TR. 2SC733P/NEC Q102 446- TR.
Page 37
PARTS LIST OF Q802/803/804 ASS'Y LOCATION PARTS No. SPECIFICATION 3028- MICA 361- HEAT SINK 1730- 10 - SCREW Q802 509- 2SC3953E Q803 509- 2SC3953E Q804 509- 2SC3953E CRT SOCKET ASS'Y LOCATION PARTS No. SPECIFICATION 6010- SOCKET HOLDER 3504- 17” D.F. CRT SOCKET PARTS LIST OF IC601 ASS'Y LOCATION PARTS No.
Page 38
Q403 706- 2SC5521Z Q405 415- TR. TIP122 Q911 600- POWER MOSFET IRF634A PARTS LIST OF Q425 ASS'Y LOCATION PARTS No. SPECIFICATION 3028- MICA HEAT SINK 1730- SCREW Q425 728- HSB772P/HSB772Z PARTS LIST OF Q420 ASS'Y LOCATION PARTS No. SPECIFICATION 6003- SCREW NUT 6015- HEAT SINK...
Page 42
IC801 MM1381 DRIVE R DRIVE ADJ CONTROL R OSD IN G OSD IN CONTRAST DRIVE B OSD IN G DRIVE ADJ ATTENUATOR ATTENUATOR VIDEO/OSD SW B DRIVE ADJ R VIDEO IN CUT-OFF ADJ VCC1 R CLAMP CAP R VIDEO OUT CONTRAST DRIVE VCC2...
Page 43
IC103 MTV016/MTV018 8 DATA DATA CCS0 DISPLAY & ROW CCS1 SERIAL DATA DAEN CONTROL BLINK INTERFACE 2 RAEN CAEN REGISTERS CRADDR VDDA LUMA VSSA CHARACTER ROM BORDER 5 RCADDR ARWDB ADDRESS BUS HDREN 9 DADDR LUMINANCE & VDREN BORDGER ADMINISTRATOR VCLKS 5 WADDR NROW...