Subscribe to Our Youtube Channel
Related Manuals for Kraus FS-1000-B
Summary of Contents for Kraus FS-1000-B
- Page 1 INSTALLATION MANUAL All-in-One Filtration Set FS-1000 / FS-1000-B www.kraususa.com Toll Free: 1.800.775.0703 © 2024 Kraus USA Plumbing LLC REV. January 3, 2024...
- Page 2 Congratulations on the purchase of your new Kraus plumbing fixture! Please keep the box and packaging materials until your product is completely installed. If you have any questions, require technical assistance or have any problems with your product: STOP DO NOT RETURN TO STORE Please contact our Customer Service Team 1-800-775-0703 / customerservice@kraususa.com...
-
Page 3: Prior To Installation
Prior to Installation: Make sure you have all necessary parts by checking the diagram and · parts list. If any part is missing or damaged, please contact Kraus Customer Service at 800-775-0703 for a replacement. · Read all instructions and safety warnings and ensure you have all tools, parts, and equipment necessary for a safe installation. -
Page 4: Tools Required
Tools Required Adjustable Wrench Drill Tape Measure Safety Goggles Utility Knife Permanent Marker Cut Resistant Gloves Care & Maintenance To keep the product clean & shining, follow the steps below: Rinse with clean water & dry with a soft cloth. ACID Do not clean with soaps, acid, polish, abrasives or harsh cleaners as use of such products may affect product performance or void the warranty. - Page 5 Diagram and Parts List Tee Adapter Manifold Polypropylene Cartridge Compressed Carbon Cartridge Quick Connect Lock Tab Mounting Screw & Anchor x 3 Tubing 1/4" x 8' 3x AA Batteries Battery Compartment...
-
Page 6: Dimensions And Specifications
Dimensions and Specifications 9 1/2" (240mm) 4 7/8" (125mm) Flow Rate 0.7GPM Capacity: 700 gallons NOTE: Depending on local water quality and use environment, the actual filtered water flow rate and total filtered water volume will vary. Min static pressure: 40 psi (275.8 kPa) Max static pressure: 120 psi (827.4 kPa) Inlet Water Temperature 41°... - Page 7 Step 1. Turn off the cold water supply and Tee Adapter turn on the faucet to relieve the water pressure and drain water from the water line. Disconnect the cold water supply line from the cold water supply valve. Install the tee adapter to the cold water supply valve.
-
Page 8: Mounting Template
Step 2. Using the mounting template, mount Fasteners the manifold. Align the mounting Cabinet holes of the manifold at the proper Wall mounting location. Mark the hole locations with a permanent marker. Place the manifold aside and pre-drill the mounting holes, if necessary, depending on the fasteners selected. - Page 9 Step 3. Insert the batteries into the battery compartment by lifting up the tabs. Drill 1/4" Hole Drill a 1/4" hole in the wall a few inches away from your filtration system. Place the anchor inside the hole and then Screw fasten the battery compartment to the wall by screwing it into the anchor.
- Page 10 Step 4. Connect the tubing. Wet one end of the tubing sections with water and press it firmly into the inlet port of the filter head. Wet the other end of the tubing and press it firmly into the tee adapter. Repeat for the other end of tubing, pressing one end into the outlet port of the filter head and the other end into the filtered water faucet supply.
- Page 11 Step 5. Install the filter cartridges. Write the date on the new filter cartridge label. Remove the cap from the filter cartridge and discard. Inspect the O-rings cartridge for any damage. Make sure both sets of O-rings are present and are positioned correctly.
-
Page 12: Filter Icon
Step 7. Display & Reset: After installing new filters push and hold the settings button for 3 seconds. Filter 1 icon will blink. Push the reset button and hold for 3 seconds and the icon will reset to full capacity. Push the settings button again and filter 2 icon will blink. -
Page 13: Troubleshooting
Troubleshooting If you have followed the instructions carefully and your faucet still does not work properly, take the following corrective steps: PROBLEM CAUSE ACTION Water leaks between the An O-ring is damaged, dirty, or Turn off the water supply, and relieve filter head and the filter cartridge. -
Page 14: Replacement Parts
NSF/ANSI 42, 53 and 401. Model: FS-1000/FS-1000-B Performance Data Sheet Replacement Filters: FC-100PP and FC-100CB Substance... - Page 15 Performance Data Sheet (based on VOC surrogate testing) Substance Influent Challenge Minimum % Reduction or Maximum Concentration mg/L Product Water Concentration Requirement mg/L alachlor 0.050 0.001 atrazine 0.100 0.003 benzene 0.081 0.001 carbofuran 0.190 0.001 carbon tetrachloride 0.078 0.0018 0.077 0.001 chlorobenzene chloropicrin...
- Page 16 This warranty is non-transferable. Kraus warrants the structure and finish of the Product to be free from defects in material and workmanship under normal usage for a period of one (1) year from the date of purchase by a trade professional or end-user of the Product from an authorized Kraus dealer.
- Page 17 TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, THIS WARRANTY DOES NOT COVER, AND KRAUS USA PLUMBING, LLC SHALL NOT BE LIABLE FOR, ANY SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES (INCLUDING LABOR CHARGES TO REPAIR, REPLACE, INSTALL OR REMOVE THIS PRODUCT), WHETHER ARISING OUT OF BREACH OF ANY EXPRESS OR IMPLIED WARRANTY, BREACH OF CONTRACT, TORT, OR OTHERWISE.
- Page 18 IMPORTANT Register Your Kraus Product Activate Your Warranty Access Premium Customer Support Get Product Information REGISTER TODAY http://www.kraususa.com/registration www.kraususa.com...
Need help?
Do you have a question about the FS-1000-B and is the answer not in the manual?
Questions and answers