Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for XIEGU XPA12B
Summary of Contents for XIEGU XPA12B
- Page 1 Product Reviews February 2023 Xiegu XPA125B 1.8-50 MHz 100 W Amplifier...
-
Page 2: Product Review
(≥25 A), high voltage (≥15 V dc), and high temperature (≥100 °C). A fault condition suspends with the Xiegu X108G, X5105, X6100, and G90 trans- ceivers, it will also work with any QRP rig. And an normal operations, normally by bypassing the ampli- internal wide-range automatic antenna tuner provides fier. -
Page 3: Performance Measurements
Table 2 details the measured amplifier input versus output. The Figure 2 — The Xiegu XPA125B two-tone test with the Elecraft KX3 set at 5 W output. XPA125B display power readings are compared to a NIST-traceable... - Page 4 Table 2 include an ATU, the XPA125B will take care of this for you. However, Xiegu XPA125B Amplifier Measurements, 13.8 V dc amplifier display. Standby: 0.16 A, key down, no drive, 2.1 A. as mentioned earlier, the XPA125B SWR meters do not work unless...
- Page 5 IMD performance was not good at all. We then found that 6 meters Xiegu had a new and improved version of the amplifier, so the editors decided to review the new unit. When we received the new version, we saw the same problem with power Input (W) output on the 10- and 6-meter bands.
- Page 6 I went outside the low range for Table 3 these tests (see the results in Xiegu XPA125B Resistive Load and Loss Testing Table 3). VS WR/Impedance 160 M 80 M 40 M 20 M 10 M The XPA125B couldn’t match 10:1/5 Ω...
-
Page 7: Building The Kit
Ham Radio Solutions CW Hotline Reviewed by Sean Klechak, W9FFF sean.klechak@gmail.com To advance my Morse code skills, I’ve continuously tried different learning methods. I eventually felt I was ready to get on the air and make CW contacts. My 20 parts to solder in this kit, all of which attach to an code transmission was slow, my code reception was included PCB and are enclosed in a plastic case. - Page 8 During my build, I used a flux pen while soldering the electrical components to the PCB. I have found flux to be critical in properly soldering components. Even with the solder-containing change, I added some via my flux pen. Finally, it could be difficult to solder components on a PCB without holding the PCB in place.
- Page 9 this portal, I connected to VBand and started prac- ticing my code in the “Practice Channel,” a private channel to practice code. This is nice because I could practice on my own or practice with QSO bot, an automated bot that simulates regular contact on CW. After some practice, I tried to make contact and prac- tice code in one of the public channels.
- Page 10 as the signal traveled through Wi-Fi. Both units were to utilizing it to work as a key while operating away on the same network, so I turned my phone into a hot from my station. At $50 per kit, it is well designed and spot and configured one of the CW Hotline devices easy to understand, and it provides an online portal for the phone’s Wi-Fi.
-
Page 11: Optional Accessories
RS-232 computer control port, a SERIAL The unit is standalone, but it can be operated re- Ethernet RJ-45 port to control the unit over IP, a USB motely via a computer, tablet, or phone (more on B port ( ) for computer control, a USB A port ( this later). - Page 12 Before connecting your rotator to the controller, will find VNC software for free on any platform, ensure you have the correct pinout for your specific including Windows, macOS, Linux, iOS, and Android, model. If you’ve just installed a new rotator, you will so you can remotely control the ARCO on any smart need to do a rotator centering.
- Page 13 Figure 14 — The main screen map recall for different Figure 13 — The ARCO settings menu tab. SYSTEM customizable altitude views. Operating the ARCO Controller The front panel touchscreen is very intuitive. Just touch somewhere on the map, and 3 seconds later it will turn.