Advertisement
When using any electrical appliance, some basic safety precautions should always be observed to reduce the risk of fire, electric shock, and/or injury to persons. Read all instructions carefully before using the appliance. Specifically:
Failure to observe the warning may result in life threatening injury by electric shock.
Failure to observe the warning could result in injury or damage to the appliance.
Danger of burns!!
Failure to observe the warning could result in burns or scalds.
Please note:
This symbol indicates recommendations and important information for the user.
THIS PRODUCT IS FOR HOUSEHOLD USE ONLY
Turn the radiator upside down on a rug or a soft surface in order to prevent damaging the paint finish.
Fully unfold the wheels by turning them outwards (Fig. 1). Turn the radiator back to its upright position.
The heater must not be placed immediately below a power outlet. Do not use this radiator in rooms having a surface area of less than 43 square feet (4 sq.m.).
Plug in the heater, the appliance will be set in the standby condition. The display will show the symbol. Keep loose clothing or bedding, furniture and flammable material away from the power outlet where the heater is plugged in. After an interruption of the power supply (power failure or appliance unplugged) the unit goes always to stand-by.
To turn the appliance on, press the (B) button.
Press button (E) to set the required power level: MIN (); MED (); MAX (). To select the desired temperature, press button + or - (C or D). By pushing the + or - button once, the temperature (shown on the display) will increase or decrease by 1°F (1°C). By keeping the + or - button depressed, the value will increase or decrease rapidly.
The appliance allows you to set the temperature from 41°F (5°C) to 82°F (28°C).
Setting the temperature to 41°F (5°C) with the "-" button, the appliance will activate the Antifreeze function.
The display will show the symbol, in this way the appliance will turn on automatically, at the max power, only if the room temperature falls below 41°F (5°C).
If you wish to go back to the Heating function, press the "+" button once. After an interruption of the power supply (probe failure or appliance unplugged) the unit goes always to stand-by.
When this function is active the appliance automatically sets the most appropriate power level to guarantee optimum comfort while reducing energy consumption. To activate this function press the "ECO" (F) button. The display will show symbol. If the selected temperature is much higher than the actual room temperature, the appliance will start automatically and rapidly begin to heat the room. The appliance will automatically select the most convenient power level (MAX-MED-MIN-OFF).
If MAX power level has been selected using the button, the appliance will cycle between: MAX-MED-MINOFF.
If MED power level has been selected, the appliance will cycle between: MED-MIN-OFF.
If MIN power level has been selected, the appliance will cycle between: MIN-OFF.
The symbol indicates the heating status by means of its colors.
RED: the unit is heating at the maximum power.
ORANGE: the unit is heating at the medium power.
GREEN: the unit is heating at the minimum power.
absent: the unit is not heating.
In order to avoid accidental operation, you can lock the keyboard using the key lock function. To activate this function during on mode, press buttons + and - together for at least 3 seconds. The display shows the symbol and a double acoustic signal will be emitted. To disactivate the function proceed in the same way.
This function can be activated in two different ways.
Delayed start: With the appliance in standby mode, press the timer button (G) . The hours left before the appliance comes on is displayed together the symbol and "h" symbol flashing. Change the hours using the + and - buttons, then wait a few seconds for the program to be stored.
The display will return to off and the symbols remains on. When the programmed time has elapsed, the appliance will come on with the previous settings.
Delayed stop: with the appliance on, press the timer button . The hours left before the appliance goes to stand-by mode, the power level and in case the function selected are displayed together with the symbol and "h" symbol flashing.
Change the hours using the + and - buttons, then wait a few seconds for the program to be stored. The current settings and symbol are displayed. At the end of the set time the appliance switches to standby mode automatically. To go back to operating without the timer, press the timer button twice. The timer symbol disappears from the display.
Please note: the time is settable from 0.5 to 24 hours.
The display can show the temperature in both °F and °C. To select the desired temperature scale, when the unit is in standby position, press and hold the "+" and "ECO" keys for at least 10 seconds, then release.
The change of scale will be indicated by two short beeps.
The appliance allows two different brightness settings for the display.
The highest is active when any key button is pressed. After a few seconds of keyboard inactivity, the brightness will decrease to the operating brightness level. This lower level can be adjusted in this way:
The appliance has a diagnostic system that makes it possible to signal malfunctions.
In case of problems, the display will show an alarm message:
A safety device switches the heater off in the event of overheating.
To restart the heater, contact the De longhi toll free number.
Always remove the plug from the power outlet and allow the radiator to cool. Wipe radiator with a soft damp cloth, do not use detergents and abrasives.
Should the radiator not be in use over a certain length of time, wind the cord around the cord holder and store it in a dry place. This appliance has been built to give many years of trouble free service.
In case of malfunction or doubt, do not try to repair the heater by yourself: this may result in a fire hazard or electric shock. Contact the De longhi toll free number.
PROBLEM | CAUSE | SOLUTION |
The display doesn't work | Be sure it is plugged in and that the electrical outlet is working | Plug into the power outlet |
The safety device may have switched o the appliance | Remove the obstruction and let the appliance cool down. If the appliance doesn't work please contact the De longhi toll free number. | |
The appliance doesn't warm up | The temperature may be set too low | Set the temperature to a higher value |
The display shows: blinking | It indicates that the room temperature sensor has failed | Please contact the De longhi toll free number. |
The display shows: (High temperature) blinking | The unit has reached a too high internal temperature | Check that the unit is not covered and let the appliance cool down. When the product internal temperature decreases, the alarm will disappear. If the appliance doesn't work please contact the De longhi toll free number. |
Here you can download full pdf version of manual, it may contain additional safety instructions, warranty information, FCC rules, etc.
Download DeLonghi TRRS2715EBK - ELECTRIC OIL FILLED RADIATOR Manual
Advertisement
Thank you! Your question has been received!
Need Assistance?
Do you have a question about the TRRS2715EBK that isn't answered in the manual? Leave your question here.