2. ABOUT THIS MANUAL 1.1 WAR NI N G S A ND I MPO RTAN T N OTI CE S The purpose of this manual is to give instructions on how to operate the LIGHTNING by Humphree system. TEC H NI CAL DOCUM ENTAT ION This manual is available digitally as a PDF file, and can be downloaded in the following ways: The i nfo rm ation in t he fo ll ow in g do cu me nt wa s correct a t t h e t i m e it wa s p ro du c e d .
CONTENTS 8. COORDINATED TURN 1. SAFETY INFORMATION 8.1 ABOUT FUNCTION 1.1 WARNINGS AND IMPORTANT NOTICES 9. PITCH & ROLL STABILIZATION 2. ABOUT THIS MANUAL 9.1 ABOUT FUNCTION 2.1 INTENDED PRODUCT USE 2.2 INTENDED AUDIENCE 9.2 HOW TO USE 10. MANUAL CONTROL 3.
3.T YP I CA L SYST EM OVE RV IEW 4 . FUN CT IO N PAC K AGES 4 . 1 D I S P L AY AVA I LA BL E F U N CT I O NS CONTROL PANEL ETHERNET SWITCH...
Page 5
5 . C O N TROL PA NEL 5 . C O N T RO L PA N EL 5 . 2 DI S P L AY F E AT U R ES 5.1 TOU CH SC RE E N G E ST UR E S MAIN SCREEN Drop down menu GPS speed...
5. CONT ROL PA NE L 5 . C O N T RO L PA N EL 5.2 D IS PLAY F EAT U RE S 5 . 3 D I S PL AY S ET T I NG S Find the display settings in SETTINGS/ SYSTEM SETUP/DISPLAY.
If your vessel runs with high trim it is likely that you are using too much fuel and not getting the speed that you could do. With Humphree Automatic Trim Control you will always have the optimum trim on your boat, with out the need of adjusting the trim system manually.
7 . AUTO L IST 7 . AUTO L I ST 7.1 ABO UT T HE F U NCT I O N 7 . 2 H OW TO U S E T HE F U N CT I O N Due to uneven loading or cross winds, the boat will often lean to one side.
COORDINATED TURN automatically controls the heeling angle of the boat during PITCH CONTROLL instructs the Lightning system to reduce unwanted pitching turns to reduce the side forces for the people on board. With a controlled heel which eliminates sea sickness and fatigue.
Page 10
1 0 . MA N UAL C O NT ROL 1 0. M A N UA L CO N T RO L Bow down Trim/list angle The trim/list angle indicators show the current boat trim Both starboard and port interceptors deploy and list angles.
Page 11
1 1. R ES ET STANDBY When the system is put in standby mode all electronic units enter a low energy RESET ANGLE CALIBRATION scheme. Go to: SETTINGS/SYSTEM SETUP/SENSOR SETUP/ANGLE CALIBRATION ENTER STANDBY To enter STANDBY open the drop down menu and slide the STANDBY slider from left to right.
Page 12
1 3. T ROU BL E S HO OT IN G To increase the durability of the system: If you are experiencing issues, visit the website below: https://humphree.com/aftermarket-support/diagnostic-trouble-codes/ • Apply antifouling to the parts that are exposed to water for more than two weeks at a time.
Page 13
13. TROU BLES HOOT ING 1 3. 2 CLEAR A LARM Tap and drag down to get to the drop-down menu. Go to SETTINGS. Select ALARMS. A list of the current alarms will be visible. Select the alarm. Follow the instruction on the screen to clear the alarm. Press RESTART SYSTEM.
Need help?
Do you have a question about the LIGHTNING and is the answer not in the manual?
Questions and answers