Table of Contents
Advertisement
Quick Links
AUTOMATIC INSTANT GAS WATER HEATER
IMPORTANT
INFORMATION
Read all instructions before using the heater
Protect the heater from rain and wind, even from
water that can flow over the edge, use for
instance, SpaDealers protective box
As gas, propane (LPG) with 30 mbar pressure
reducer and 1,5 ‐ 2 kg/h of gas flow is used
Place the supplied rubber seal between the
brass connector and gas inlet on the stove, see
page 5
Check that there are no gas leaks before the
stove is used, see pages 5 ‐ 6
At freezing temperatures the stove should be
disconnected and stored in a warm place to
prevent freezing damage
Also remember to empty the connection hoses
If you have any questions, contact us at
support@spadealers.fi
OPERATING
INSTRUCTIONS
When operating the gas water heater always make sure that there is good ventilation. During operation the
gas water heater will produce carbon monoxide which is harmful if inhaled in large quantities. It is
therefore important that all users strictly observe the proper installation instructions and use as prescribed
in this manual. Repair of this product should not be undertaken by other than authorized and qualified
personnel.
OWNER'S MANUAL
Advertisement
Table of Contents
Related Manuals for SpaDealers TN11
Summary of Contents for SpaDealers TN11
- Page 1 OWNER’S MANUAL AUTOMATIC INSTANT GAS WATER HEATER IMPORTANT INFORMATION Read all instructions before using the heater Protect the heater from rain and wind, even from water that can flow over the edge, use for instance, SpaDealers protective box As gas, propane (LPG) with 30 mbar pressure reducer and 1,5 ‐ 2 kg/h of gas flow is used Place the supplied rubber seal between the brass connector and gas inlet on the stove, see page 5 Check that there are no gas leaks before the stove is used, see pages 5 ‐ 6 At freezing temperatures the stove should be disconnected and stored in a warm place to prevent freezing damage Also remember to empty the connection hoses ...
-
Page 2: Table Of Contents
&S ............................... 8 AINTENANCE ERVICES & .................... E rror! Bookmark not defined. ROUBLE ROUBLESHOOTING 2422‐GAR‐7002/09 ‐ GAS WATER HEATER Caution: Appliance type B11 （JSD‐FD‐12L） Read the technical instructions before Model TN11 （JSB‐FD‐12L) installing the appliance Type of gas 13B/P‐30mbar (LPG) Read the user’s instructions before Applicable water pressure 0.25Bar – 10Bar, 0.025 ‐ 1.0 MPa lighting the appliance Hot water supply capacity 10L/min △t=25℃ Minimum useful output, P 8KW This appliance shall only be installed outside or in a room separated from Maximum useful output, ... -
Page 3: Features
EATURES Water controlled, fully automatic and easy to operate. Open the water valve, start pump to start ignition. The hot water will come out immediately. Close the water valve, stop pump. The hot water stops and the flame goes out immediately. Ability to start at very low water pressure, applicable for many places. If the flame goes out unexpectedly during use, the gas supply will shut off automatically to protect against gas leakage. If the water pressure is too high, the water will come out from the security valve to release pressure, ensuring safety for the appliance and the user. Equipped with a protection unit to prevent over‐heating in the water tank and “dry‐burn”. In the event of pressure fluctuations in the water supply, the water heater will maintain a relatively constant outlet water flow. (This instruction is for the functions of the external housing only, and does not represent the external shape of other models.) Outer structure 1. Air input 2. Warning stitch 3. Technical label 4. Smoke discharge joint 5. Gas flow 6. Burners 7. Water flow 8. Battery box 9. Water inlet (cold) 10. Water outlet (hot) 11. Ignition switch 12. Safety valve 13. -
Page 4: Installation
3. It is forbidden to install the heater outside if it’s not protected from wind and rain, because wind and rain may put out the flame; Moreover, the appliance might get frozen and damaged in a cold winter season. 4. A water supply with a minimum 0.02Mpa water pressure is required on the installation site to ensure the normal operation of the water heater. 5. We recommend a cold water valve be installed close to the water heater for maintenance convenience. See Fig 4. 6. Keep a minimum space from the wall or ceiling on the installation site. Keep clear of stove, combustible and dangerous objects. See Fig 3. 13. Gas inlet 14. Water inlet (cold) 15. Water outlet (warm) 17. Air hole (Fig. 4) 7. If it’s possible, install the water heater at the proper height for easy inspection of burning, about 1.5m. 8. Make sure a proper gas pipe are installed and make sure that the pipe remains airtight and the inlet gas pressure is 30mbar, 2h/kg for normal operation of the appliance. If using a piped gas supply, ask the gas supplier or the gas administration authority for pipe connecting. See “OTHER IMPORTANT CAUTIONS” for other regulations. NSTALLATION PERMANENT WALL MOUNT Hanging and installing the water heater (for reference only) Mark the holes on the wall, the position is subject to the actual model of your water heater, drill 4 holes of 8mm, put in the plastic dowels if needed. ... -
Page 5: Nstallation Of As Pipe
NSTALLATION OF AS PIPE Hose must be designed for LPG gas and a maximum of 1.2 m long and 10 mm internal diameter. Or according to other national standard. Attachment of the hose must be secured with a hose clamp at both ends. Use the included coupling with gasket so that the gasket sits against the gas inlet on the heater. If using a piped gas supply, ask the gas supplier to connect the pipe. Use pressure reducer 30mbar, 1,5 ‐ 2 kg/h (not included). Examples of correct gas reducers and incorrect ones 50 mbar The types of gas cylinders and connection methods of low pressure regulators (30mbar, 1.5 ‐ 2kg / h) can vary. It is important that the correct low pressure regulator is used. Here are examples of the right type and also incorrect types. NEVER USE an adjustable controller. Note that the amount of gas that the stove needs to give full effect is 1.5 kg / h. With a flow of 1 kg / h, the effect will be reduced. NSTALLATION OF OT AND OLD ATER IPE Use hoses that can withstand pressure to connect incoming and outgoing water connection. Note that the outgoing pipe also must withstand temperatures up to 70 °C SER NSTRUCTIONS ... - Page 6 TART IGNITION ATER OMES Start the ignition: Open the cold water valve, (or start the pump) the burner attempts to ignite a flame with a repeating “pa”sound, which stops after ignition is achieved; hot water comes out immediately. Note: When using this appliance for the first time, or after a long idle period between uses, repeated ignition attempts are needed to discharge any air in the gas pipe. "G ", "W " "P " ONTROLS ATER AND OWER ‐ The knob "GAS" controls the gas flow to the burner and thus the power. ‐ There are three sections for the gas burner in the heater, one in the middle, one on the left side and one on the right side. When the knob "Power" is in the Max position, all three sections are on, at Min only the section in the middle is on and the power is about 8 kW. ‐ "Water" must always be set to Max. If it is set to Min then the water flow through the heat exchanger will decrease and result in a much higher water temperature out of the heat exchanger. This results in the overheating thermostat, which is located in the pipe out of the heat exchanger, turning off the heater. ATTENTION! This will also happen in all situations where the water flow drops below 7 l/min and a possible reason could then be that the filter in front of the pump is dirty. ‐ For a temporary stop during use, close the water valve or stop the pump. The burner goes out automatically. Open the valve or start the hot water pump again. ‐ NOTE: Because the water inside the water heater will be very hot during a temporary shutdown, wait a few seconds before coming into contact with the water. ...
-
Page 7: Prevent Fire
N CASE OF GAS LEAKAGE NEVER MAKE A FIRE OR TOUCH ANY ELECTRIC SWITCHES NOT MAKE TELEPHONE CALL IN THE ROOM OPEN ALL DOORS AND WINDOWS Regularly check the pipe to make sure of good air tightness. If cracked, replace the pipe at once. Under normal conditions, the gas pipe needs to be checked once a year. If the gas pipe is cracked, stop using it and replace it. For users of Propane: if the flame of the water heater is inconsistent, it may be due to a malfunction of the gas pressure reducer, Stop using the pressure reducer and replace it, or get it repaired and installed by a professional technician. NOTE! Yellow flame can also be caused by dirt in the burners. For users of piped gas or natural gas: if the flame is abnormal, it is due to an unstable gas pressure. Stop using the water heater temporarily. Continued use will damage the water heater and possibly cause an accident. REVENT IRES It is absolutely forbidden to leave the burning water heater unattended. The water heater must be stopped before going to bed or going out. It is forbidden to put combustible or explosive objects close to the water heater. Never put a towel or clothes on the exhaust vent. A gas leakage from the gas pipe can easily causes a fire. 1. Air intake 4. Smoke discharge joint 13. Gas inlet 18. Ventilation hatch 19. Hot water 20. Air extraction (Fig.7) REVENT XYGEN EPLETION AND NCOMPLETE URNING • Because a large quantity of oxygen is used during burning, the installation site for the water ... -
Page 8: Ther Mportant Autions
THER MPORTANT AUTIONS • : if there is a need to use hot water shortly after the hot REVENT BURNS FROM HOT TEMPERATURES water valve is closed, do not come into contact with the first‐ hot water coming, as it could cause burns due to a temporary high temperature. • : In very cold areas (with temperatures below 0℃), move it to REVENT THE HEATER FROM FREEZING a storage place without risk for freezing. • Some parts of the water heater may become loose due during transportation. In case of damages to the external housing after opening the package, get a repairman to check before use. EPLACE THE ATTERIES • Replace the batteries if you see the following situations upon ignition or as the water comes out. • Longer interval of sounds of “Pa‐Pa‐Pa” during ignition (approx. 2 sounds a second) • The flame goes out shortly after ignition. • The voltage between the poles of the battery is lower than 2.9 V. “L ” OW TO REPLACE THE BATTERIES SEE PARAGRAPH OADING THE ATTERY FOR DETAIL • Please use moisture proof batteries with a sealed metal shell. Under normal conditions, the batteries need replacing once a year. BNORMAL ANDLE •...
Need help?
Do you have a question about the TN11 and is the answer not in the manual?
Questions and answers