Advertisement
Quick Links
Advertisement
Related Manuals for RCbro SPARROW V3 Pro
Summary of Contents for RCbro SPARROW V3 Pro
- Page 1 SPARROW V3 Pro ® RCbro SPARROW V3 Pro Manual v1.2 LefeiRC www.lefeirc.com/...
-
Page 2: Table Of Contents
SPARROW V3 Pro ® RCbro Disclaimers and Warnings Please use this product within the scope permitted by local laws and regulations. LE FEI does not assume any legal liability resulting from any illegal use of this product. This product is a remote-control aircraft model. Please strictly abide by the safety operating regulations of model aircraft products. -
Page 3: Parameter
SPARROW V3 Pro ® RCbro Parameter ➢ SIZE: 33*25*13mm WEIGHT: 16.5g ➢ POWER INPUT: 2-6S (MAX 80A) OUTPUT(PMU): 5V/4A 9.5V/2A FC: 5V(PMU) VTX/CAM: 9.5V(PMU) SERVO: onboard 5V(PMU) or external BEC ➢ RC RECEIVER Protocol： PPM SBUS IBUS ELRS/CRSF Telem：MAVLINK、CRSF Interface ➢... - Page 4 SPARROW V3 Pro ® RCbro PPM/SBUS/IBUS/CRSF MAVLINK CRSF GPS-RX GPS-TX S4-S8 AUX Channel(S4 defaults to RUD) CAM1-2 Dual camera VTX/CAM power supply Battery Servo power G/GND *It is recommended to remove the propeller during installation and debugging, pay attention to safety! ➢...
- Page 5 SPARROW V3 Pro ® RCbro ➢ Large current When the current is large, it is recommended to tin the exposed pad during soldering, as shown in the picture below! When the current is too large and the battery power supply capacity is insufficient, it may cause the OSD to flicker.
- Page 6 SPARROW V3 Pro ® RCbro ◐ RSSI RSSI channel can be selected, and the range of RSSI value is the same as that of other channels. When using ELRS, if the RC cannot set an independent RSSI channel, you can set <RSSI>...
-
Page 7: Osd&Led
SPARROW V3 Pro ® RCbro OSD&LED ➢ MAIN Flight Mode Throttle Time Acceleration health Temperature GroundSpeed Volatge Horizon Line Cell Voltage Altitude Current Climb Rate Distance Voyage Return Home Angle Power Consumption Flight Direction Latitude and Longitude Satellite Desired Attitude Angle... - Page 8 SPARROW V3 Pro ® RCbro ➢ PARAMETERS Calibrate the RC RC CALI CHANNEL TYPE A-E-T-R or T-A-E-R RSSI RSSI MAIN CHANNEL CH5/CH6 SUB CHANNEL CH5/CH6/CH7/CH8/CH9/CH10 MAIN MODE1 MAIN MODE2 STAB/MAN/ACRO/ALT/RTH/FENCE/HOVER/ALT*/SUB MAIN MODE3 SUB MODE1 SUB MODE2 STAB/MAN/ACRO/ALT/RTH/FENCE/HOVER/ALT* SUB MODE3 TIMEOUT RTH...
- Page 9 SPARROW V3 Pro ® RCbro S4 FUNC S5 FUNC Set S4-S8 multiplex function, if set to throttle, it will have S6 FUNC differential function S7 FUNC S8 FUNC S1 MID S2 MID S4 MID S5 MID Set the servo neutral position...
-
Page 10: Flight Mode
SPARROW V3 Pro ® RCbro FC DATA Sensor data display LANGUAGE Chinese or English. *When setting the servo function, RC6-12 means the RC 6-12th channel. > *< FENCE RADIUS only works in fence mode, other modes do not have fence function. -
Page 11: Preflight Inspection
SPARROW V3 Pro ® RCbro ➢ Assisted Takeoff Push the throttle to enough power, after takeoff(throw it away), the aircraft ALT/FENCE/ALT*: will climb to 20m automatically. Push the throttle to enough power, shake the aircraft or run, then the motor starts... - Page 12 SPARROW V3 Pro ® RCbro ➢ RC control direction *If the control direction is not correct, you can set the channel output reverse in the RC. *After setting the feedback direction, the control direction can only be modified in the RC.
- Page 13 SPARROW V3 Pro ® RCbro When calibration is needed: It is recommended to perform level calibration when using the FC for the first time; after changing the installation direction, it is necessary to perform level calibration again; it is recommended to perform level calibration after it has not been used for a long time.
-
Page 14: Faq
SPARROW V3 Pro ® RCbro Q. Important question! ! ! A. Failsafe is very important and must be set! It is recommended to record DVR when using for the first time! Q. The rudder surface response is too small in STAB or other modes. - Page 15 Q.What type of GPS can be used for flight controller? A. The SPARROW V3 Pro support protocol is UBLOX and does not support the NMEA protocol. Therefore, please pay attention when choosing. The series that support UBLOX include the 6th, 7th, 8th, 9th and 10th generations.
-
Page 16: Accessories Description
SPARROW V3 Pro ® RCbro Accessories Description Camera wire x 2: Compatible with CADDX and other camera wire sequences. Be sure to check whether the wire sequence needs to be modified before use. VTX wire x 1: Compatible with PandaRC and other VTX wire sequences. Be sure to check whether the wire sequence needs to be modified before use.
Need help?
Do you have a question about the SPARROW V3 Pro and is the answer not in the manual?
Questions and answers
By default Sparrow v3 pro channel are set on AETR...how to change that to my setup EATR