Advertisement
Quick Links
Advertisement
Related Manuals for SwedHeat SPARSET
Summary of Contents for SwedHeat SPARSET
- Page 1 Assembly instructions List of items needed: Bubble level Drill Rubber hammer Measuring tape Hammer...
- Page 2 2,70 m...
- Page 7 Mint Sauna Side Name Width Height Length Quantity 3D Front Axonometry view Front wall 1926 1926 Back wall 1926 1926 1926 Left wall 1426 1426 Right wall 1426 1426 Heater protection parts Heater cover Heater cover Sauna beds Sauna bed 1900 Bed holders Bed holder...
- Page 8 Roof panel holders Panel 1350 holder Panel 1910 holder Sauna Corners Corners 2160 Corner covers Covers 2160 Covers 2160 Covers 2160 Brackets for doors and windows Frame 1881 bracket Window 1881 bracket Cover for heater wires Wire cover 1820 Doors and windows Sauna door 1912 Sauna...
- Page 9 Introduction of sauna parts Corner cover Corner Roof panel Back wall Panel holder Right wall Bed holder Panel holder Left wall Bed holder Frame brackets Heater cover Corner Front wall Corner cover...
- Page 10 Pay attention to Pre-drill holes Drive the screw in pre- the position of for screws drilled holes the part Make sure the length is the same Keep distance >10cm from walls >10cm 5x80mm for fastening corners to walls...
- Page 11 Pre-drill holes for screws Use rubber hammer for wall parts Make sure to level for better building accuracy Drive the screw in pre- drilled holes 5x80mm for fastening corners to walls...
- Page 12 Pre-drill holes for screws Use rubber hammer for wall parts Make sure to level for better building accuracy Make sure that the height of the sauna is 2160 mm 5x80mm for fastening corners to walls Drive the screw in pre- drilled holes...
- Page 13 Pre-drill holes for screws Drive the screw in pre- drilled hole 1. Insert the door frame brackets into the existing hole 2. Pre-drill holes for screws 3. Drive the screw in pre-drilled hole Drive the screw in pre-drilled 5x80mm for fastening corners to walls holes on the door frame brackets 5x80mm for door frame brackets...
- Page 14 Insert the hinges into the door glass 1. Insert the hinges into the door glass. 2. After that put the door glass in the door frame that is factory assembled...
- Page 15 ! Make sure the glass is centered between the door frame Mark places for drilling Drill the marked points for the hinges Screw hinges to door frame 4x35mm for fastening hinges...
- Page 16 Place the door in between the door frame you attached earlier Pre-drill holes for screws Drive the screw in pre- drilled hole 5x100mm for fastening door frame...
- Page 17 Pre-drill holes for screws Drive the screw in pre- drilled hole 3x35mm for fastening door frame covers...
- Page 18 The recommended height for bed holder installation is 700mm for upper bed holder and 400mm for lower bed holder, but you can customize it according to you Pre-drill holes for screws 700 mm Drive the screw in pre- drilled hole 400 mm 5x55mm for fastening bed holders...
- Page 19 Place the upper sauna bed on the holder and fasten with screws. We recommend to leave the lower sauna bed loose so you can adjust it if needed 5x55mm for Pre-drill holes fastening sauna for screws beds Use screws to fasten sauna Make sure to level bed in pre-drilled holes when installing bed...
- Page 20 Sauna heater protection assemble and installation Pre-drill holes for screws Assemble sauna heater protection as shown in the picture above Drive the screw in pre- drilled hole Make sure to level when installing heater protection 210 mm If possible, adjust the height of the heater protection according to the heater purchased.
- Page 21 Pre-drill holes for screws 50-55mm Drive the screw in pre- drilled hole Apply sealing tape on roof panel holders 5x55mm for fastening panel holders...
- Page 22 Pre-drill holes for screws Drive the screws into the pre-drilled holes for the panel holder in the roof panel Connect roof panels as shown above 5x55mm for fastening roof panels...
- Page 23 Place corner covers as shown on picture above 2x30mm for corner covers Nail the corner covers to hide screws...
Need help?
Do you have a question about the SPARSET and is the answer not in the manual?
Questions and answers