Must LP1800 Series User Manual

Rechargeable lifepo4 battery
Hide thumbs Also See for LP1800 Series:

Advertisement

Rechargeable LiFePO4 Battery
LP1800 Series
User Manual

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the LP1800 Series and is the answer not in the manual?

Questions and answers

Summary of Contents for Must LP1800 Series

  • Page 1 Rechargeable LiFePO4 Battery LP1800 Series User Manual...
  • Page 2: Table Of Contents

    This manual introduces the MUST LP1800 series, please read this manual before installing the battery, and follow the instructions carefully during the installation process. If you have any doubts, please contact MUST for assistance immediately. 1. Safety Instructions...............1 1.1 Before connecting..............2 1.2 In Using..................2...
  • Page 3: Safety Instructions

    5) Do not expose the cable to the outside. 6) Do not connect power terminal reversely. 7) All battery terminals must be disconnected for maintenance. 8) Please contact the supplier within 24 hours if there is something abnormal. 9) Do not use detergent to clean the battery.
  • Page 4: Before Connecting

    8) Keep the battery away from water and fire. 1.2 In using 1) If you need to move or repair the battery system, you must cut off the power supply and turn off the battery completely. 2) It is forbidden to connect the battery with different types of batteries.
  • Page 5: Introduction

    LP1800 series lithium iron phosphate battery is a new energy storage product developed and produced by MUST, which can provide reliable power support for various equipment and systems. The LP1800 series has a built-in BMS battery management system, which can manage and monitor battery voltage, current, temperature and other information.
  • Page 6: Product Specification

    12.8V 25.6V 51.2V 10.8-14.6V 21.6-29.2V 43.2-58.4V 14.6V 29.2V 58.4V 0.5C 0.5C CE/UN38.3/MSDS >4500 at 25℃...
  • Page 7: Equipment Interface Instruction

    2.3 Equipment interface instruction ADDS:DIP switch setting instructions...
  • Page 10 definition Port Definition Definition definition 1.Under parallel status, Communication address 0001 is Master battery pack, rest communication position are slave battery. And slave battery could communication with master battery pack through RS458 port. master battery pack will collect all slave battery data. 2.When parallel status, only master battery pack communicate with PC upper computer as remote monitoring, uploading datas, displaying status &...
  • Page 11 RJ45 port(X2-A) process...
  • Page 12: Battery Cables Terminal

    Clarifying MUST...
  • Page 14: Safe Handling Guide Of Lithium Battery

    Inverter PV ARRAY Public Grid Local Load Battery Module...
  • Page 15: Safety Gear

    It is recommended to wear the following safety gear when dealing with the battery pack 4. Installation and Operation 4.1 Package Items Unpack and check the pakcing list (1) For battery module package: ①Single battery pack stanard package:1pc orange、black water proof terminal and OT(100A) ②Could be customization per require:battery cable、communication cable、parallel cable、grounding cabel.
  • Page 16: Installation Location

    (2) For battery system connecting to inverters: Two long power cables (current capacity 120A, constant 100A) and one communication cable for each energy storage system: 4.2 Installation Location Make sure that the installation location meets the following conditions: (1)The area is completely water proof. (2)The floor is flat and level.
  • Page 17: Put Into Cabinet Or Racks

    (2)Install a grounding cable to the grounding point of the modules. 4.4 Put into cabinet or racks Put battery modules into cabinet and connect the cables:...
  • Page 18: Power On

    After installation, do not forget to register online for full warranty. 4.5 Power on (2)The one with empty Link Port 1 is the Master Battery Module, others are slaves (1 master battery configure with maximum 15 slave batteries):...
  • Page 19 (3) Press the red SW button of master battery to power on, all the battery LED light will be on one by one from the Master battery:...
  • Page 20: Power Off

    Note: (1) After the battery module powered on, the soft-start function takes 3sec to active. After soft-starts battery ready to output high power. (2) During capacity expansion or replacement, when parallel different SOC/voltage of module together, please maintain the system in idle for ≥15mins or till the SOC LED becomes similarly(≤1dot difference) before normal operation.
  • Page 21: Trouble Shooting

    5.Trouble shooting Problem determination based on (1) Whether the battery can be turned on or not. (2) If battery is turned on, check the red light is off, flashing or lighting. (3) If the red light is off, check whether the battery can be charged/discharged or not.
  • Page 22 (2.4) Low Voltage: When the battery discharges to 44.5V or less, battery protection will turn on. Solution: Charge the battery till the red light turns off. (2.5) Cell voltage high. The module voltage is lower than 44V, SOC LED does not all on. When discharge the module protection disappear. Solution: keep charge the module by 57.6-58.4V or keep the system cycle.
  • Page 23: Emergency Situations

    then try turn on the single module, without any cable connected. If still buzzer rings. Then it is mosfail. Switch off the module and contact your local distributor. (6) After switch On, the module turns on directly (6.1) BMS failure. Solution:...
  • Page 24: Remarks

    (4) Damaged Batteries Damaged batteries are dangerous and must be handled with the utmost care. They are not fit for use and may pose a danger to people or property. If the battery pack seems to be damaged, pack it in its original container, and then return it to Pylontech or an authorized dealer.

Table of Contents