XL Systems 0001955 Quick Start Manual

XL SYSTEMS INC
14 Dora Ln Holmdel, NJ 07733
Item #0001955
N Diesel DCC Decoder for Atlas GP7, GP9, GP30, GP35...
• Two diesel prime movers with randomly associated locomotive sounds
• User selectable 22 different horns and 8 bells
• 28 accessory functions allowing more sound control than ever
• Programmable individual sound volumes
• 1.0 amp capacity
• Programmable for either 2-digit (1-127) or 4-digit (1-9999) addresses
• Programmable start voltage
• Programmable acceleration rate
• Programmable deceleration rate
• Programmable top voltage
• Programmable 14, 28, 128 speed steps
• Selectable factory default speed curve
• Supports advanced consisting (CV19)
• Supports programming on the main (OPS mode)
• Compatible with NMRA DCC standards
• Complies with Part 15 of FCC
• Speaker included
INSTALLATION: Disassemble loco and tape the frame around the motor spring
contact as Fig1 indicates. The motor spring contact should not touch the frame.
The decoder replaces the original circuit board of the locomotive and should fit in
the same location. Assemble one half of the frame first, installing the decoder,
motor, driveshafts, bearings, trucks, and frame spacers. Gently place the other
frame half on top of the completed half, checking clearances and if there is any
binding of the drive mechanism. Correct any trouble spots at this point. Also
check to make sure the motor brush tabs are not touching the frame halves and
the clear tape is correctly positioned at the motor brush tab points to avoid
shorting out the decoder. Now you can install the insulated bolts and nuts to
secure both frame halves together. Apply tape on the chassis under the speaker
to prevent the speaker from touching the chassis.
DCC OPERATION: The decoder has been factory programmed with address #3, 28/
128 speed steps and maximum top voltage. This decoder has start up and shut
down feature. You must press any function key to start up the engine before
operating the loco. To shut down the engine you must bring the loco to idle and then
press F8 3 times. Please refer to the CV Chart to explore other features of the
decoder.
TROUBLE SHOOTING: Whenever the decoder doesn't work, please use the program
track to program CV# 125 with value 1 to restore the decoder to factory settings. This
should bring the decoder to life with address #3. This decoder should perform well with
all DCC systems.
RETURN PROCEDURE: This decoder carries a 6 month warranty against factory
defects. This warranty does not include abuse, misuse, neglect, improper
installation, or any modifications made to this decoder, including but not limited to
the removal of the NMRA plug if applicable. If it should become necessary to return
the decoder for warranty repair/replacement, please include a letter with your
name, address, daytime phone number, and a detailed description of the problem
you are experiencing. Please also include a check or a money order for $10.00 to
cover return shipping and handling. If the decoder is no longer considered under
warranty, then please contact XL Systems for a price quote to cover the cost of
repair or replacement of the decoder, and return shipping and handling. Customers
outside the continental United States, including; Hawaii, Alaska, Canada and
Mexico, have to contact us for exact return shipping rates for both warranty and
non-warranty repairs.
Contact to us at linzping@gmail.com.
Send the decoder to: XL SYSTEMS INC. 14 DORA LANE HOLMDEL, NJ 07733
FUNCTION CHARTER
Function
F1
F2
F3
F4
F5 Brake release / brake squeal
F6
F7 Air hose firing/uncoupling lever
F8 Click 3 times will shut down when in idle/Manual notch down
F9 Engine cooling fan / Manual notch up
F10 Rail wheel clack (only moving)
F11
F12 Change prime diesel rumble type (CV123, 2 types)
F13
F14
F15
F16
F17
F18 Change bell type (8 types plus off)
F19 Horn type select (total 22 different horns plus off)
F20
F21 Change bell volume and turn on the bell
F22
F23 Change diesel rumble volume
F24
F25
F26
F27
F28
Idle/Moving
Bell on/off
Horn
Air release
Coupling 1
Dynamic brake on/off
Traction air compressor
Short air release
Coupler crash
Air compressor
Flange squeal
Air release
Associated loco sound
Change horn volume
Safety valve pop
Air release
Flange noise
Sand drop
Air release