Advertisement
4. ASSEMBLY & INSTALLATION
4.1.
AIR SUPPLY
4.1.1.
Ensure buffer air valve (or trigger) is in the "off" position before connecting to the air supply.
4.1.2.
You will require an air pressure of 90psi, and an air flow according to specification.
WARNING! Ensure the air supply is clean and does not exceed 90 psi while operating the buffer. Too high an air pressure and unclean air
‰
will shorten the product life due to excessive wear, and may be dangerous causing damage and/or personal injury.
4.1.3.
Drain the air tank daily. Water in the air line will damage the buffing kit.
4.1.4.
Clean air inlet filter weekly. Recommended hook-up procedure is shown in fig 1.
4.1.5.
Line pressure should be increased to compensate for unusually long air hoses (over 8 metres). The minimum hose diameter should be
1/4" I.D. and fittings must have the same inside dimensions.
4.1.6.
Keep hose away from heat, oil and sharp edges. Check hose for wear, and make certain that all connections are secure.
4.2.
COUPLINGS
Vibration may cause failure if a quick change coupling is connected directly to the buffing kit. To overcome this, connect a leader hose to
the buffing kit. A quick change coupling may then be used to connect the leader hose to the air line recoil hose. See fig.1 & 2.
fig.1
4.3.
5. OPERATION
WARNING! Ensure you read, understand and apply safety instructions before use.
‰
Note: Numbers shown in brackets refer to item numbers in the parts list.
WARNING! Disconnect from air supply before changing accessories or servicing.
‰
5.1.
The buffing wheel (34) attaches directly to the arbor (28) and should be tightened using the wrench (33).
5.2.
To use the grinding stones (39) screw the 10mm drill chuck (35) onto the arbor (28). Insert the required grinding stone into the chuck
and secure using the chuck key provided. Remember to remove the chuck key.
5.3.
Depress the trigger to operate the buffing kit.
6. MAINTENANCE
WARNING! Disconnect buffer from air supply before changing accessories, servicing or performing maintenance. Replace or repair
‰
damaged parts. Use genuine parts only. Unauthorised parts may be dangerous and will invalidate the warranty.
6.1.
Lubricate the buffer daily with a few drops of Sealey air tool oil dripped into the air inlet to prolong its life.
6.2.
Clean the buffing kit after use. DO NOT use damaged stone wheels.
6.3.
Loss of power or erratic action may be due to the following:
a) Excessive drain on the air line. Moisture or restriction in the air pipe. Incorrect size or type of hose connectors. To remedy
check the air supply and follow instructions in section 4.
b) Grit or gum deposits in the buffing kit may also reduce performance. If your model has an air strainer (located in the area of
the air inlet), remove the strainer and clean it. Flush the buffer out with gum solvent oil or an equal mixture of SAE No 10 oil
and paraffin.
Allow to dry before use.
6.4.
For a full service contact your local Sealey service agent.
6.5.
When not in use, disconnect from air supply, clean buffer and store in a safe, dry, childproof location.
ENVIRONMENT PROTECTION
Recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be sorted,
taken to a recycling centre and disposed of in a manner which is compatible with the environment. When the product
becomes completely unserviceable and requires disposal, drain any fluids (if applicable) into approved containers and
dispose of the product and fluids according to local regulations.
Note: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior
notice. Please note that other versions of this product are available. If you require documentation for alternative versions, please email or call
our technical team on technical@sealey.co.uk or 01284 757505.
Important: No Liability is accepted for incorrect use of this product.
Warranty: Guarantee is 12 months from purchase date, proof of which is required for any claim.
Sealey Group, Kempson Way, Suffolk Business Park, Bury St Edmunds, Suffolk. IP32 7AR
01284 757500
© Jack Sealey Limited
sales@sealey.co.uk
Original Language Version
fig.2
www.sealey.co.uk
SA92.V3 Issue 2 (H,F) 23/03/23
REGISTER YOUR
PURCHASE HERE
Advertisement
