Table of Contents
Advertisement
Quick Links
Blu-ray Player
Copyright 2014 WOOX Innovations Limited.
All rights reserved. No part of this publication may be reproduced, stored in a retrieval system
or transmitted, in any form or by any means, electronic, mechanical, photocopying, or otherwise
without the prior permission of WOOX Innovations. Philips and the Philips'Shield Emblem are
registered trademarks of Koninklijke Philips N.V. and are used by WOOX Innovations Limited
under license from Koninklijke Philips N.V.
Published by Niki & Sam WK1502
Subject to modification
Version 1.2
TABLE OF CONTENTS
Location of PC Boards & Versions Variation ........................ 1
Specifi cations ....................................................................... 2
Safety Instruction .................................................................. 3
Software Upgrade Instruction..................................................4
Troubleshooting.................................................................... 5
Disassembly Instructions ..................................................... 6
Set Block Diagram ................................................................ 7
Set Wiring Diagram .............................................................. 8
Circuit Diagram & PCBA Layout........................................... 9
Set Mechanical Exploded View ..........................................10
Revision List ........................................................................ 11
BDP2305/F7/12/X77
Page
3140038 62630
Advertisement
Table of Contents
Related Manuals for Philips BDP2305/F7
Summary of Contents for Philips BDP2305/F7
- Page 1 WOOX Innovations. Philips and the Philips’Shield Emblem are registered trademarks of Koninklijke Philips N.V. and are used by WOOX Innovations Limited under license from Koninklijke Philips N.V.
-
Page 2: Pcb Locations
PCB Locations LOADER PF BOARD MAIN BOARD VERSION VARIATIONS Type / Versions BDP2305 Service Policy Board in used MAIN BOARD MAIN BOARD PF BOARD LOADER WIFI MODULE C -- Component Lever Repair Tips： ＊ M -- Module Lever Repair... -
Page 3: Electrical Specifications
1 Electrical Specifications 1.1 Mains Voltage / Mains Cord Stroke Voltage Frequency AC Cord Type Version 220V-240V 50Hz VDE 2-pins round 220V-240V 50Hz VDE 2-pins round INMETRO 2-pins round mainscord(INMETRO-to-2-pins flat adaptor /55/78 100V - 240V 50Hz, 60Hz to be included) 100V - 240V 50Hz, 60Hz 2-pins flat... - Page 4 1.5 Additional Requirements for India 1.5.1 VoltageRange Check The set should work NORMALLY at mains voltage from 170V to 280V AC. (Incases of set with Audio amplifiers, at lower mains voltages, audio rated poweroutput might be lower against the specified power at nominal mains voltage, butremaining performance should be unaffected).
-
Page 5: Mechanical Specifications
2 Mechanical Specifications 2.1 Mechanical Strength and Ease of Control 2.1.1 Mechanical Strength Set exterior parts such as lens, buttonsetc, shall be able to withstand a force of 50N during 30 seconds from all possible directions. The rigid test finger, according to IEC60065 clause: 9.1.8 should be used. Set shall be proof against a pinch force of 150N, loaded by a bare hand. -
Page 6: Support Foot
2.2.2 a) Detachable mains cord inlet has to withstand minimal 2500 insertions and withdrawals. b) Mains cord operating force should be within the following limits: • Withdrawal Force, P: 10N ≤ P ≤ 50N • F ≤ 50N Insertion Force, F: 2.3 Visibility of User Interface Displays &... - Page 7 2.6 Touch Control Criteria • 2.7 Bezel and Tray loader design 2.7.1 Strength Permissible load on Bezel in any direction is ≥ 5 0N.The Tray & Bezel should not be broken or permanently deformed, nor cause damage to other parts of set. The Bezel may dislodge above 30N without suffering any damage, and the user must be able to easily put the Bezel back.
-
Page 8: Noise Specifications
2.11 Noise Specifications Test Conditions: Measurements are to be made inside an Anechoic Chamber (echo-free environment) with ambient noise of less than 16dBA. Measurements are to be taken at the following positions: (a) Top-Surface and at center of Front-Cabinet (b) Front-Surface and at center of Front-Cabinet The microphone is to be positioned 10cm from abovementioned surfaces. - Page 9 The visibility of flow lines, sink marks, scratches, unevenness and flashes has to be judged at a distance of 30 cm, with normal overhead lighting (800–1000 lux): Surface Area Requirements For highly visible surfaces Very high appearance requirements: None or very small flow lines (≤ 5mm) may occur None or very small and faint injection-marks / sink- marks may occur No burrs, scratches or other defects may be visible...
- Page 10 2.12.2.3 Resistance to Dry Abrasion Test method A fixed load of 2.5 N is used for this method. The specific pressure depends on the size of the area to be tested. This implies, in relation to real use in practice, a higher load on ribs, raised lettering, etc. The abrasive wheel is made from 3 discs of abrasive material (Scotch Brite Cleaning and finishing material type A-VFN, thickness 6.35mm).
-
Page 11: Transportation & Handling
• To get a better insight in the real worn effect, test have to be performed starting with a load one step lower and ending with a load one step higher then defined load. 2.13 Transportation & Handling 2.13.1 POS & Label Adhesion and Print Requirements 2.13.1.1 Label Adhesion For Removable Labels (e.g. - Page 12 2-10 2.14.1.2 For China & India Regions ONLY...
- Page 13 2-11 2.14.2 Packaging Robustness Test Specifications Note: To conduct this during Design Verification Test (DVT) phase only. Purpose is to reveal weak points in the Product or Packaging and to take preventive actions to strengthen these points so as to ensure a more robust Product/Packaging. The test is referenced to ISTA-2A standard as follows: Drop Sequence: (a) Drop on 1x Corner, 3x Edges, 6x Faces...
- Page 14 2-12 No of layer in stack: As indicated on Packaging Box graphics Note: If simulated weight is used, a very rigid flat Plate shall be placed over a single layer of packages, and the weights shall be evenly distributed over the plate. Test Criteria: After the test, the packaging and its content should still be in good physical condition.
-
Page 15: Electromagnetic Compatibility
2-13 3 Regulatory 3.1 Safety Player shall as a minimum comply with the requirements laid down in IEC 60065:2001/A1:2005. This is applicable to all countries. However, in countries having national safety standards, which differ from IEC60065, the relevant national standards are applicable, For European countries: EN60065(latest addendum) For USA, Canada: UL60065 All Information technology equipmentshall as a minimum comply with the requirements laid down in IEC60950-... -
Page 16: Electrostatic Discharge Immunity
2-14 ETSI EN 301 489-17 v.2.1.1 (2009-05)for European countries ETSI EN 300 328 v1.7.1 (2006-10)for European countries In countries where EMC standards are not compulsorily enforced, CISPR22 must be enforced. 3.3 Electrostatic Discharge Immunity Standard Reference: IEC61000-4-2:2001 The product shall withstand electrostatic discharges on all user accessible parts. 3.3.1 Contact Discharge Voltage level... - Page 17 2-15 3.4.2 Mains Drop-out Immunity Standard Reference: IEC 61000-4-11:2004 - Variation 0% (= 100% dip) at T-event = 50msec. Performance criteria B - Variation 40% (= 60% dip) at T-event = 100msec. Performance criteria B - Variation 0% (= 100% dip) at T-event = 1 sec. Performance criteria C Additional for USA: - Variation 0% (= 100% dip) at T-event = 100msec in standby mode.
- Page 18 • Thick Disc: 1.5mm Philips Thin disc • Thin Disc: 1.1mm • Vertical Deviation: _0.5mm Philips VDD disc Philips ECC disc • Eccentricity: 200μ Philips 8cm skew disc • Skew: 0.6_ • i l i unbalance SCD-4013 • Birefringence: 150μ...
- Page 19 • Substrate thickness test disc2 test disc3 test disc4 Horror Disc, no set 520µm 670-730µm 560- hang up allowed. 530µm SVD-4010 • Birefringence: 150μ Philips Hair scratch test disc • Hair scratch Glass CVP02.19 disc • Glass substrate DVD Double Layer Philips LVP11.01A TDV-545 • Black dot: 1100μ...
- Page 20 2-18 TDV-R521CW • Scratch: 3mm • Vertical deviation: _0.5mm TDV-R533CW TDV-R513CW • Eccentricity: 150μ DVD–RW TDV-MW525CW • Black dot: 1000μ TDV-MW525CW • Normal Fingerprint: 65μ TDV-MW525CW • Heavy Fingerprint: 75μ TDV-MW521CW • Scratch: 3mm • Vertical deviation: _0.5mm TDV-MR533CW TDV-MW513CW •...
- Page 21 Solder Joint...
- Page 22 Preparation to Software Upgrade 1. Procedure for software upgrade a) Upgrade from USB: 1) Go to www.philips.com/support to check if the latest software version is available for this player. 2) Build UPG file in USB 3) Copy the upgrade file to USB UPG folder.
-
Page 23: Troubleshooting Chart
Trouble shooting chart No light on LED, and buttons do not work No light on LED, and buttons do not work Check every supply Check whether the voltage on main board is connection of line is normal(Pin 4 is 5v in XP1 on power board) Fix it Check the power board... -
Page 24: No Audio Output
Trouble shooting chart No audio output No audio output Check whether the P3 is ok Peplace P3. Check whether R611 ， R612 ， C616 ， Add them C614，R613 is on Peplace the main IC and reset the software. - Page 25 Trouble shooting chart Remote control does not work Remote control does not work Check whether the remote Replace the battery for remote controller’s battery controller exhausted or not. Check the ET4002 power Check the VCC net no front board supply ET4002 （PIN16 ）is about 3V Replace ET4002...
- Page 26 Trouble shooting chart Can’t read disc or can’t open the disk door Can’t read disc or can’t open the disk door Check whether Check the connection 4pin cable from the DVD loader running is main board normal Check 45pin 8pin cable from main board Fix the connection the 45pin cable or connection to the loader is...
- Page 27 Trouble shooting chart No HDMI output No HDMI output Check if J2 is ok Replace J2 Check If F1 is on Add F1 is 0 ohm Replace the main board...
- Page 28 Trouble shooting chart Can not connect to network Can not connect to network Check UTH16C52 Fix U12 in mainboard (U12) is on In mainboard Check if the P1 is ok Or not Change P1...
- Page 29 5- 7 Trouble shooting chart Can not connect to WIFI Can not connect to WIFI Check USB401 (pin4) Check the R969 is fixed on voltage is 3.3v the mainboard Check the order of wifi Check the connection wire:yellow\white\red from wifi board to to yellow \white\red mainboard Change the wifi module...
-
Page 30: Mechanical And Dismantling Instructions
Mechanical and Dismantling Instructions Dismantling Instruction Detailed information please refer to the model set. The following guidelines show how to dismantle the player. Step1:Open the top cover. Remove 2 screws on the back panel ,then open the top cover. Step2: Dismentle the front panel .Connect power and boot,than open the tray . And than pull up the front panel Step3 Step3: Dismantle the Loader.Remove 2 screws baside the Loader. - Page 31 Mechanical and Dismantling Instructions Dismantling Instruction Detailed information please refer to the model set. The following guidelines show how to dismantle the player. Step4: Dismentle the PF board.Remove the screw on the wirless board and disconnect the connector ,than pull up the wirless board.And than remove 2 screws on the PF board Step5: Dismentle the main board.Remove 2 screws on the back panel.
-
Page 32: Block Diagram
Block Diagram: MAIN BD Coaxial HDMI MAIN IC MT8551 PDAG NT5CB64M16FP DH CW1117 CW1117 Loader IM 640W 3.3V 9.5V 1.5V G5175RV1U 1.2V DC DC AS5422AD/TR LF KEY1 PW BD LED Light KEY2 Power IC signal DNY176/177 KEY1 KEY2 IR BD power... -
Page 33: Wiring Diagram
Wiring Diagram: MAIN BD 45pin Loader 4pin IM 640W 8pin USB401(4pin) ( p ) 4pin XP3(12pin) 12pin IR BD PW BD XP1(12pin) wire 4pin connector... - Page 34 Circuit Diagram- Main Board: G5175 G5175 MODE 2.2uF/10V/Y5V 2.2uF/10V/Y5V 0.1uF/16V/Y5V 0.1uF/16V/Y5V V33P 3.3V_STBY 2.2uF/10V/Y5V 2.2uF/10V/Y5V 100K 100K PGOOD 2.2uF/10V/Y5V 2.2uF/10V/Y5V LDO(0.15A) LDO(0.15A) PVCC1_1 PVCC1_2 0.1uF/16V/Y5V 0.1uF/16V/Y5V 10uF/10V/Y5V 10uF/10V/Y5V 1.2V 0.1uF/16V/Y5V 0.1uF/16V/Y5V 2.2uH 2.2uH COMP1 LX1_1 LX1_2 10uF/10V/Y5V 10uF/10V/Y5V 2.2K/1% 2.2K/1% 10uF/10V/Y5V 10uF/10V/Y5V 4700pF/50V/X7R...
-
Page 35: Circuit Diagram- Main Board
Circuit Diagram- Main Board: 1.5V 1.5V 0.1uF/16V/Y5V 0.1uF/16V/Y5V 0.1uF/16V/Y5V 0.1uF/16V/Y5V 10uF/10V/Y5V 10uF/10V/Y5V 0.1uF/16V/Y5V 0.1uF/16V/Y5V 0.1uF/16V/Y5V 0.1uF/16V/Y5V RDQ2 RDQ10 DDRVCCIO RDQ0 RDQ6 RDQ12 DDRVCCIO RDQ0 RDQ1 RDQ3 RDQ7 DDRVCCIO RDQ1 RDQ2 RDQ4 RDQ2 DDRVCCIO RDQ2 1.5V RDQ3 RDQ0 DDRVCCIO RDQ3 RDQ4 RDQ7 RDQS1 DDRVCCIO... - Page 36 Circuit Diagram- Main Board: 1.2V 1.2V DVCC12_K DVCC12_K AC12 RDQ0_B RDQ3_B RA0_B DVCC12_K RDQ0_B AC13 RDQ1_B RDQ7_B RA1_B 0.1uF/16V/Y5V 0.1uF/16V/Y5V 22uF/6.3V/Y5V 22uF/6.3V/Y5V 0.1uF/16V/Y5V 0.1uF/16V/Y5V 0.1uF/16V/Y5V 0.1uF/16V/Y5V 0.1uF/16V/Y5V 0.1uF/16V/Y5V DVCC12_K RDQ1_B AD13 RDQ2_B RDQ2_B RA2_B DVCC12_K RDQ2_B AE13 RDQ3_B RDQ6_B RA3_B DVCC12_K RDQ3_B AD21...
- Page 37 Circuit Diagram- Main Board: Differential Signal ! AVDD33_VDAC No Through Hole ! 3.3V AVDD33_VDAC 100 ohm - Impedance RN100 RN100 4.7*4 4.7*4 AOLRCK F_TX2+ AOSDATA0 CH2_P AVSS33_VDAC AOSDATA1 CH2_M F_TX2- AOSDATA2 CH1_P F_TX1+ AOSDATA3 CH1_M AOSDATA4 AVDD33_VDAC_R F_TX1- 3.3V AVDD33_VDAC_R F_TX0+ CH0_P SPDIF...
- Page 38 Circuit Diagram- Main Board: 3.3V 3.3V 3.3V 3.3V AVDD33_USB 4.7K 4.7K NC/10K NC/10K NC/10K NC/10K NC/10K NC/10K NC/10K NC/10K NC/10K NC/10K DVCC33_IO AVDD33_USB 3.3V DVCC33_IO C114 C114 C116 C116 DVCC33_IO NFD7.1 DVCC33_IO AMUTE I/O7 0.1uF/16V/Y5V 0.1uF/16V/Y5V 0.1uF/16V/Y5V 0.1uF/16V/Y5V NFCEN NFD6.1 DVCC33_IO AVSS33_USB I/O6...
- Page 39 Circuit Diagram- Main Board: 3.3V_STBY 3.3V_STBY VOUTD3 TP29 TP29 VOUTD3 VOUTD4 TP30 TP30 VOUTD4 VOUTD5 TP31 TP31 VOUTD5 3.3V_STBY VOUTD6 TP32 TP32 VOUTD6 GPIO0 DVCC33_IO_STB GPIO0 DVCC33_IO_STB GPIO1 DVCC33_IO_STB GPIO1 TP101 TP101 UARXD UARXD UATXD UATXD 3.3V_STBY VSTB VSTB AVDD33_LDO VDATA AVDD33_LDO VDATA...
- Page 40 Circuit Diagram- Main Board: TRINC TRINC TRINC V14REF TRIND TRIND TRIND C148 C148 0.1uF/16V/Y5V 0.1uF/16V/Y5V A1.2V V14REF AVDD12_1 URXD URXD FEGIO10 AVDD12_1 FVREF UTXD UTXD FEGIO11 FVREF AVDD12_2 HAVC VDAC0 VDAC0 VDAC0 HAVC HAVC TRINA VWDC3O VWDC3O VWDC3O TRINA C502 C502 TRINB FEGAINSW2...
- Page 41 Circuit Diagram- Main Board: MVCC_T VCC_D FB19 FB19 MOTOR DRIVER TI2050G4 0.1uF/16V/Y5V 0.1uF/16V/Y5V 10uF/10V/Y5V 10uF/10V/Y5V MVCC_T TPIC_TR+ TPIC_TR+ M12V_T U409 U409 TPIC_TR- TPIC_TR- TPIC_A+ TPIC_TL- SLED1_P P5V_2 TPIC_TL- TPIC_A- TPIC_CO_B- TPIC_TL+ SLED1_N STP2_N TPIC_TL+ TPIC_CO_B+ C757 C757 R1359 R1359 TPIC_FR- P12V_3 STP2_P TPIC_FR-...
- Page 42 Circuit Diagram- PF Board: LED1 LED1 LED_GREEN LED_GREEN CON4 CON4 IRM_16mm IRM_16mm C311 C311 C314 C314 C315 C315...
- Page 43 9-10 9-10 Circuit Diagram- PF Board: DuPont pin +12V IROUT USBP USBM USB_VCC VSTB VSCK VSDA 14PIN/2.0mm 14PIN/2.0mm VSCK OPEN/CLOSE VSDA VSTB STANBY/ON IROUT IR_VCC USB_VCC KEY1 OPEN/CLOSE KEY1 OPEN/CLOSE USBM OPEN/CLOSE R305 R305 R328 R328 2.2K 2.2K USBP IR_VCC R321 R321 4PIN/2.0mm...
- Page 44 9-11 9-11 Circuit Diagram- PF Board: CY502 CY502 1000pF/250VAC 1000pF/250VAC C501 C501 R503 R503 R502 R502 1500pF/1KV 1500pF/1KV 150K 150K 150K 150K D501 D501 D503 D503 R501 R501 T501 T501 LF501 LF501 CE502 CE502 30mH 30mH 15uF/400V 15uF/400V CE501 CE501 1000PF/100V/X7R 1000PF/100V/X7R 15uF/400V...
- Page 45 9-12 9-12 Print Layout-Main Board(top):...
- Page 46 9-13 9-13 Print Layout-Main Board(bottom):...
- Page 47 9-14 9-14 Print Layout-PF Board:...
-
Page 48: Exploded View
10-1 10-1 Exploded View: WIFI MODULE... -
Page 49: Revision List
REVISION LIST V 1.0 2014-12-29 Initial release for BDP2305/F7 . V 1.1 2015-1-8 Initial release for BDP2305/ 12 2015-1-8 Initial release for BDP2305X/ 77 V1.2...