Table of Contents
Advertisement
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for CMP TROLLMaster PRO3+
Summary of Contents for CMP TROLLMaster PRO3+
- Page 1 P/N TMPRO3PLUS 02MANTMPRO3PLUS V3...
- Page 2 Congratulations on your purchase of the Wireless TROLLMaster PRO3+. This addition to the TROLLMaster lineup will allow you to control both your trolling speed and direction from anywhere in the boat. CONNECTIONS Power/Battery Connection 6’ (1.8m) Red, 6’ (1.8m) Black Connect the red 16AWG to positive 12V battery terminal.
-
Page 3: Mounting Holes
Servo Connection 8’ (2.4m) This wire will connect to the included Servo that mounts under the cowling of the motor. For more details on how to install this servo refer to the Hardware Kit you purchased that corresponds to vout specific make of motor. Route and secure servo cable as far away as practical from the spark plug wires. -
Page 4: Remote Functions
REMOTE FUNCTIONS Power On/Off Backlight Screen Idle/Resume Throttle Faster 2 AAA Batteries Replace by removing Slower two screws Left/Right Steering* Lanyard Hook POWER Power On To power on your remote, push the Power On/Off button for one second. You will see TROLL Master on the screen. Select any function to start using the remote. -
Page 5: Throttle Control
THROTTLE CONTROL You have a range of 1-250 to adjust your speed. This does not correlate to your actual GPS speed. Use an external GPS in order to get an accurate speed reading for your situation. Speed Adjustment There are two buttons to control your speed, a rabbit icon for increasing your speed and a turtle icon to decrease your speed. -
Page 6: Installation Instructions
INSTALLATION INSTRUCTIONS Packaged in the hardware kit that you purchased with your PRO3+ is an install manual that explains in detail how to Install your servo and throttle rod. 2. Your wireless receiver needs to be placed in a location where it will not be exposed to constant water exposure. -
Page 7: Troubleshooting
6. (Optional Steering Device) Route the steering cable 6ft (1.8m) from your receiver to the location of your Panther Electro Steer motor and connect the 2-Way molded connector until they are fully engaged. Do not plug into the 3-way molded connector in an existing relay control. NOTE: Keep in mind that depending on which side your electro steer is mounted on your kicker motor the turn controls might be reversed. -
Page 8: Service And Warranty
The warranty coverage on this equipment is limited to the terms set forth below: CMP Group LTD. warrants this product to be free of defects in material and workmanship for a period of ONE (1) YEAR from the date of original retail purchase. - Page 9 This warranty gives you specific legal rights, and you may also have other legal rights, which may vary from state to state. FOR SERVICE CALL +1 (757) 916-9676 CMP Group LTD. 7733 Progress Way, Delta, BC, Canada V4G 1A3 https://trollmasters.com/...
- Page 10 LANYARD STOP SWITCH EXTENSION The purpose of a lanyard stop switch is to turn off the engine when the operator moves far enough away from the operator’s position (as in accidental ejection from the operator’s position) to activate the switch. Please refer to your Lanyard Stop Switch (or similar) section of your manual for all information related to that safety feature.
- Page 11 FCC: 2AILDTMPRO3-PLUS IC: 21604-TMPRO3PS This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.
- Page 12 EXPAND YOUR PANTHER EXPERIENCE WITH THESE CMP GROUP BRANDS: Solutions for motor mounting, remote steering, tilt & trim, shallow water anchors, and security systems. Rod holders, trolling motor supports, and GPS/Sonar mounts. Auxiliary outboard motor steer systems. Throttle control for gas powered auxiliary motors.
Need help?
Do you have a question about the TROLLMaster PRO3+ and is the answer not in the manual?
Questions and answers
have power to the troll master receiver put does not even light up. any ideas. thanks
I'm not planning on connecting to ACC+ switch. Should the unit still power on when connected directly to the battery? It's not showing it's getting power. The pairing light isn't lighting up