Advertisement
Quick Links
CONTENT
Ⅰ. Istruction.............................................................3-4
Ⅱ. Operation Instruction..........................................4-7
Ⅲ. Operation............................................................7-10
Ⅳ. System detection and troubleshooting..............10-12
Ⅴ. After-sale service...................................................12
1
Advertisement
Subscribe to Our Youtube Channel
Related Manuals for VEVOR HZX-100D
Summary of Contents for VEVOR HZX-100D
- Page 1 CONTENT Ⅰ. Istruction.............3-4 Ⅱ. Operation Instruction..........4-7 Ⅲ. Operation............7-10 Ⅳ. System detection and troubleshooting....10-12 Ⅴ. After-sale service...........12...
- Page 2 INSTALLED MACHINE...
- Page 3 1. Components: Main control board, keypad, 128 * 64 liquid crystal display, stepper drive, stepper motor, roller. 2. Technical details: 2.1. Model: HZX-100D 2.2. Power: 220V 50/60HZ 2.3. Cutting length: 0.1-----9999.9mm 2.4. Cutting width: 100mm 2.5. Weight: 26KG 2.6. Dimension: L360*W250*H350 mm 3.
- Page 4 produced cutting width of 120mm, 160mm, 200mm, 260mm, 300mm and other pipe cutting machine, more can be customized according to requirements. 3.5. Lack of material automatically shut down, do not need to specifically stare., With a variety of manual operation, easy to debug.
- Page 5 Speed: Press this key, then press the number keys to set the speed range between 00-99, the faster the number of the faster, and vice versa slower. UNIT Batch: Press this key, then press the number keys to set the batch, the position between 0-9999, if the batch is set to 0, it will not be suspended.
- Page 6 Function: Set the parameters of several special functions. Remarks: F key: Is the "function" "FUN" key. F0: Press the "function" and then press the number key "0" key, the following other key combination operation the same. F0, [Next knife delay] cutter under a certain delay time and then on the knife (the default value is 0) F1, [Next knife interval] Cylinder knife delay time between each knife (default is 0)
- Page 7 Compensation value F3 = (set value - actual value) / actual value * 1000 = (100-90) /90*1000=111.11 F4, [Pipe cutting speed] set the cutter speed, the initial value of 18, according to the material hardness adjustment, soft material can be set to larger. F5, [Step Length] In the standby mode, press the "Forward"...
- Page 8 4. Press the "Cutter" button to set the number of times each cutting tool. 5. Press the "Total" key to set the total number of crop belts. 6. Press the "batch" button, set the number of cut for a batch. Each time the batch value will be suspended for a certain time.
- Page 9 If you press multi-digit, you can press the back (-) key to return to the previous digit. Cut A Total Speed 00-99 Press the number keys Select the appropriate speed, the speed from 00-99 points of the 100 speed section, the greater the value the faster the faster, when the material is more flexible or the whole roll material is heavy and no auxiliary feeder with the speed should be selected the slower.
- Page 10 If the setting is wrong, for example, the length is set to 800.5mm, the other is correct, you can repeat the first step to correct. Place the material: the material to the upper wheel and the next wheel contact, press the forward (+) button, so that the material forward to more than the knife-edge position, adjust the barrier board, spacer plate fixed material, so that the material will not left, right But do not grip the material so as...
- Page 11 When the sensor There instructions, Please contact the senses the object, sensor signal is correctly input seller check whether motherboard, the D2 LED on the motherboard failure motherboard lights up at the indication, short-circuit Please contact the same time CON1 interface in the direction seller of the CON5 two pins, this time if the D2 light, the motherboard...
- Page 12 the "stop" So that D11 goes out, the system can return to normal. If D11 is not extinguished please contact the seller. Ⅴ. After-sale service 1. Warranty from the date of purchase for one year. 2. The following conditions are not covered by the free warranty.
Need help?
Do you have a question about the HZX-100D and is the answer not in the manual?
Questions and answers