Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for rollease acmeda PIVOT ARM
Summary of Contents for rollease acmeda PIVOT ARM
- Page 1 PIVOT ARM INSTALLATION MANUAL v3.2 | August 2022...
-
Page 2: Table Of Contents
SECTION C | TROUBLESHOOTING DISCLAIMER INTRODUCTION This Installation manual for Pivot Arm Systems has been produced by Rollease Acmeda to supply the necessary information for the safe and correct installation of a Pivot Arm System. DISCLAIMER Rollease Acmeda has used reasonable care in preparing the information included in this document, but makes no representations or warranties as to the completeness or accuracy of the information. -
Page 3: Section A | Installation Preparation
Measuring Tape • Pencil ADDITIONAL ITEMS REQUIRED - NOT SUPPLIED To assemble an Pivot Arm, the following non-stocked items are required: • Fixings for Box/Open Brackets/Hardware (ensure appropriate fixings are used to suit application) • Trims to conceal packing (if required) Page. -
Page 4: Part B - Pre-Assembled Shade Components
NOTE: Store clip until required (can be left in adaptor as shown) CHECK SHADE ITEMS: • Shade Tube Assembly • Pivot Arms x2 • Open Bracket Assembly Page. 4 Pivot Arm Installation Manual | v3.2 | August 2022 ©Copyright All Rights Reserved Rollease Acmeda... -
Page 5: Part C - Preparing Installation Space
Check if top of installation space is level. • If H1 ≠ H2, corrective actions may need to be If W2 ≥ W1, W1=Blind Width considered prior to installation Note: Packing of Pivot Arm Bracket may be required BLIND WIDTH = W2 DROP (mm) 2040 2000 If W2 <... -
Page 6: Section B | Installation
Ensure 2 fasteners are used per side. Ensure brackets are aligned and level. Measure brackets end to end to confirm measurement is correct. Page. 6 Pivot Arm Installation Manual | v3.2 | August 2022 ©Copyright All Rights Reserved Rollease Acmeda... -
Page 7: Part C - Blind Installation
STEP 2 – INSERT RETAINER CLIP MKII INTO IDLER ADAPTER Note: • Ensure pin is clipped in securely • Tighten the Screw Page. 7 Pivot Arm Installation Manual | v3.2 | August 2022 ©Copyright All Rights Reserved Rollease Acmeda... -
Page 8: Part D - Attach Arms
BOX 120 OPEN BRACKET FACE FIX ACMEDA SCALE:1:50 PIVOT ARM TOTAL LENGTH C VEUE - Pivot Arm - OPEN - FF+TF - PIVOT ARM LENGTH SYSTEM DESCRIPTION: MAX DROP D MAX DROP D Acmeda 110 Northcorp Boulevard F +61 3 9355 0115 PROPRIETARY &... - Page 9 BAR END CAPS STEP 6 – SLIDE BOTH CLAMP PIECES ONTO WEIGHT BAR (X2) NOTE: Ensure 2 clamps are attached to the Terminal Bar. Page. 9 Pivot Arm Installation Manual | v3.2 | August 2022 ©Copyright All Rights Reserved Rollease Acmeda...
- Page 10 STEP 9 – TIGHTEN CLAMPS ONTO TERMINAL BAR STEP 10 – REMOVE RETAINING PIN THEN INSTALL COVER NOTE: DO NOT REMOVE PIN UNTIL PIVOT ARM BRACKETS, FABRIC & TERMINAL BAR ARE SECURE. Pivot Arms are free to move when pin is removed. Page. 10 Pivot Arm Installation Manual | v3.2 | August 2022...
-
Page 11: Part E - Insert Cover
Ensure weight bar has correct clearance and that fabric does not rub against box cover. PART F - INSTALLED PIVOT ARM ASSEMBLY OPEN Page. 11 Pivot Arm Installation Manual | v3.2 | August 2022 ©Copyright All Rights Reserved Rollease Acmeda... -
Page 12: Section C | Troubleshooting
4. Terminal Bar lifts up near Motor is FT (Fabric Tension) Mode Refer to motor instructions to deactivate FT Mode. bottom limit (motor control) Page. 12 Pivot Arm Installation Manual | v3.2 | August 2022 ©Copyright All Rights Reserved Rollease Acmeda... - Page 13 DOCUMENT CHANGE NOTES REVISION CHANGES v3.2 | August 2022 Corrected typo on page 8. Page. 13 Pivot Arm Installation Manual | v3.2 | August 2022 ©Copyright All Rights Reserved Rollease Acmeda...
Need help?
Do you have a question about the PIVOT ARM and is the answer not in the manual?
Questions and answers