Pioneer RX-510 Operating Instructions Manual

Operating
Instructions
STEREO CASSETTE TAPE DECK RECEIVER
RX=-510/RX=710
STEREO TURNTABLE
PL=-21IO0AZ/PL-2102/
PL-31I0Z
The Models PL-210Z and PL-310Z are not solid in the U.S.A. and Canada.
Thank you for buying this Pioneer product.
Please read through these operating instructions so you will
know how to operate your model properly. After you have
finished reading the instructions, put them away in a safe
place for future reference.
In some countries or regions, the shape of the power plug
and power outlet may sometimes differ from that shown in
the explanatory drawings. However, the method of con-
necting and operating the unit is the same.
WARNING: To prevENT FIRE OR SHOCK HAZARD, DO
NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.
IMPORTANT NOTICE
{For U.S. and Canadian models]
The serial number for this equipment is located on the
rear panel. Please write this serial number on your en-
closed warranty card and keep it in a secure area. This is
for your security.
[For Canadian model]
CAUTION: 1o prevent ELECTRIC SHOCK DO NOT USE
THIS (POLARIZED) PLUG WITH AN EXTENSION CORD, RECEPT-
ACLE OR OTHER OUTLET UNLESS THE BLADES CAN BE FULLY
INSERTED TO PREVENT BLADE EXPOSURE.
ATTENTION: pour preveniR LES CHOCS ELEC-
TRIQUES NE PAS UTILISER CETTE FICHE POLARISEE AVEC UN
PROLONGATEUR UNE PRISE DE COURANT OU UNE AUTRE
SORTIE DE COURANT, SAUF SI LES LAMES PEUVENT ETRE IN-
SEREES A FOND SANS EN LAISSER AUCUNE PARTIE A DEC-
OUVERT.
TWO VOLTAGE SELECTOR SWITCHES
Only multi-voltage models are provided with these
switches. U.S. and Canadian models are not provided
with these switches.
Mains voltages in Saudi Arabia are 127 V and 220 V only.
Never use this model with 110 V setting in Saudi Arabia.
FEATURES
CHECKING ACCESSORY ITEMS .
BEFORE OPERATION ...
ANTENNA CONNECTIONS
CONNECTIONS .....
PANEL FACILITIES
REMOTE CONTROL UNIT FACILITIES
TURNTABLE FACILITIES (OPTIONAL)
HOW TO HANDLE CASSETTE TAPES
GRAPHIC EQUALIZER CONTROLS ....
CONTENTS 1
The line voltage selector switches are on the rear panel. Be-
fore your model is shipped from the factory, these switches
are set to the power requirements of the destination. Check
they are set properly before plugging the power cord into
the household wall socket. If the voltage is not properly set
or if you move to an area where the voltage requirements
differ, adjust the selector switches as follows.
1. Use a medium-size screwdriver,
2. First, insert a screwdriver into the groove of the voltage
selector at the top, and adjust so that the tip of the
groove points to the voltage value of your area.
3. Next, insert a screwdriver into the groove of the voltage
selector at the bottom and adjust until the voltage is the
same as at the top.
Both switches must
be in the same switch
setting.
CHANNEL STEP SWITCH
Only multi-voltage models are provided with this switch.
U.S. and Canadian models are not provided with this
switch. (This switch is on the rear panel.)
The unit has been factory preset to the channel allocation
for the area in which it is to be sold. If the value is set incor-
rectly, the frequency display may stop at the wrong fre-
quency, or sound may be distorted, resulting in an inability
to reproduce reception signals at their proper sound quality.
For this reason, be sure to confirm that the value is set cor-
rectly before first using the unit.
(100 kHz/10 kHz] position:
Set to this position for areas with
FM reception step of 100 kHz, AM CHANNEL STEP
10 kHz.
FM/AM
[50 kHz/S kHz] position: S0/eKH:
Set to this position, for areas with LOQ/1O- RHE
FM reception step of 50 kHz, AM 9
kHz.
When unsure about the channel allocation for your area,
consult your dealer for correct information.
PRELIMINARY OPERATIONS
BASIC OPERATIONS 13]
TAPE COPYING: sascsecoiiestuseiseutsssnesviceseviscisteachsassdsssdsin
RECORDING AND PLAYBACK
USING THE OPTIONAL AUDIO TIMER 0... cee 16
MIC MIXING
{excluding U.S. and Canadian models)
MAINTENANCE
TROUBLESHOOTING
SPECIFICATIONS
YQ PIONEER'
The future of sound and vision.