Subscribe to Our Youtube Channel
Related Manuals for Vais Technology SEER
Summary of Contents for Vais Technology SEER
- Page 1 VAIS TECHNOLOGY www.vaistech.com Installation Manual SEER-MAN-001 WARNING: Cancer and Reproductive Harm - www.P65Warnings.ca.gov Copyright (C) 2003-2020 VAIS Technology Published July 1, 2020...
- Page 3 Liability Disclaimer: This application guide is based on the testing results at the time of publishing. VAIS Technology can not be held liable for damages or injuries caused by, or resulting from use of this guide. Strictly adhere to all car manufacturer warnings that pertain to the disassembly, maintenance, or servicing of the vehicle and any of its associated part systems.
-
Page 4: Table Of Contents
Tools Required What’s Included Installation Standard Integration CAN bus Integration Example Diagram Tips & Tricks Customization & Templates... -
Page 5: Tools Required
Tools Required VAIS TECHNOLOGY... -
Page 6: What's Included
Input / Output Harness (SEER-ZZ-HNS-002) Antenna Harness (SEER-ZZ-HNS-003) Power Harness (SEER-HNS-001) Antenna x2 (SEER-ZZ-ANT-001) **Antenna Antenna Bracket x2 Extension x2 (SEER-ZZ-BRK-001) * Replacement Bolt (92750A716) and Washer (95060A330) are available at McMaster Carr. ** 8ft Antenna Extension (SEER-ZZ-HNS-004), 20ft Antenna Extension (SEER-ZZ-HNS-005) - Page 7 Installation - ‘Antenna Extension’ ATTENTION Use the appropriate ‘Antenna Extension’ based on where the ‘Control Module’ will be located. 20ft. (609cm) 8ft. (243cm) See examples below. Option A ‘Control Module’ installed behind the dash Antenna Antenna Control Module 8ft. (243cm) 20ft.
- Page 8 Installation - ‘Antenna’ Mounting Use ‘Antenna Bracket(s)’ to secure each ‘Antenna’ Bend tabs for extra mounting or break o when not needed Use universal mounting tabs or template holes to secure ‘Antenna Bracket’ to the vehicle Avoid electrical contact ATTENTION when mounting to Aluminum Aluminum Surface Aluminum Surface...
- Page 9 Installation - ‘Antenna’ Mounting & Extension Routing Option A A x ‘Antenna’ rear to ‘Antenna Bracket’ Secure ‘Antenna’ to ‘Antenna Bracket’ using supplied hardware Option B A x ‘Antenna’ front to ‘Antenna Bracket’ Side tabs can be used for wire management. Route to ‘Antenna Harness’...
-
Page 10: Installation
Installation - Connecting the Extensions Route each ‘Antenna Extension’ to the planned mounting location of the ‘Control Module’ . • Mount in dry and safe location • Secure the ‘Control Module’ in place • DO NOT block BT Cover (See Pg. 9) From Front ‘Antenna’... - Page 11 Installation - Connecting the Extensions Connect both extension ‘Antenna Extension(s)’ to each pair of leads as shown (Pairs are separated by tape. DO NOT mix pairs.) Antenna Harness (Top View) Antenna Harness (Front View) Antenna 1 Antenna 2 Antenna 2 Antenna 1 CONNECT TOGETHER Option A: Ground...
- Page 12 Installation - Connecting the ‘Control Module’ ATTENTION Use the supplied ‘Fuse Link’ when connecting to 12V Assemble all connectors to ‘Control Module’ and connect Constant Power and Ground. CONSTANT BATTERY POWER ONLY Expansion (Not Used) Antenna Harness Buzzer I/O Harness ATTENTION Mating Connectors Buzzer and LED are not included.
- Page 13 Ignition and one lead to Input #0 (Solid White Wire) on the I/O Harness. Vehicle Ignition Connect to: Input #0 (Solid White Wire) START See the SEER Flow Editor tutorial for more information on programming mode...
- Page 14 Pink IN 2 Brown IN 3 White NOT USED Marker indicates advanced capabilities See SEER Flow Editor Expert Mode for Details 12V vehicle Sources include: SEER Inputs accept: • Ignition • Trigger Events (+/-) • Accessory • Impulse Events (+/-) •...
-
Page 15: Standard Integration
OUT 8 Black Ground Black/Blue Ground Marker indicates advanced capabilities See SEER Flow Editor Expert Mode for details Marker indicates high current capabilities See SEER Flow Editor Expert Mode for details STANDARD INTEGRATION CAN bus INTEGRATION Outputs can be connected directely... -
Page 16: Can Bus Integration
CAN bus Integration ATTENTION CAN BUS MODULE IS NOT INCLUDED. SEER can be connected directly to many industry standard CAN bus integration modules. Refer to 3rd party module wiring diagram for details. Outputs (To Car) OPTIONAL CAN bus CAN bus Module... -
Page 17: Example Diagram
Example Diagram Control Module Power Harness Antenna Harness Buzzer Fuse Link Fuse Antenna Extension (See Pg. 5) Antenna Antenna Bracket 12V (+) (See Pg. 4) CAN bus Connect Together OPTIONAL CAN bus Module is Not Included CAN bus Module Outputs (To Car) -
Page 18: Tips & Tricks
Tips & Tricks - Relays REVERSE POLARITY 12V (+) Output (-) Negative Trigger Fused 12V (+) LIGHT FLASH Negative Output (-) Left Lamp (+) Right Lamp (+) Fused 12V (+) DOORLOCK ACTUATORS Fused 12v(+) (-) Lock Output (-) Unlock Output To Lock Actuator To Lock Actuator... -
Page 19: Customization & Templates
Refer to the Insert Diagram for template wiring details. FLOW EDITOR SEER Flow Editor is used to customize and con gure the module to t your custom vehicle application needs. (See Example Below) Refer to the tutorial training for further details. - Page 20 SEER product(s). Manufacturer does o er a limited warranty to replace or repair the control module.
Need help?
Do you have a question about the SEER and is the answer not in the manual?
Questions and answers