Advertisement
IMPORTANT: MAINTAINING
BATTERY HEALTH
• Your massager is designed with a lithium-ion battery pack for cordless
convenience, increased massage duration per charge, and frequent use
and recharging.
• To maintain charge capacity and prevent battery damage, all lithium-ion
batteries must be regularly used and recharged.
• For optimal battery health, keep the battery at approximately 50% state
of charge when not in use.
• All batteries naturally lose charge when not in use. If you will not be using
the massager for an extended period, check the massager at least
every 30 days to ensure the battery is at approximately 50% state of
charge. Recharge as needed to maintain a 50% state of charge but do
not overcharge.
• IMPORTANT: DO NOT store the battery for an extended period with
above 60% or below 40% state of charge. An incorrect state of charge
during storage could irreparably damage the battery and may result in
reduced charge capacity, inability to maintain charge, failure to
recharge, or complete inoperability of the massager.
• For the health of the battery, always store the massager in a cool, dry
place. The storage location should have a consistent temperature
between 40°F and 70°F (5°C and 20°C) as well as a relative humidity at
70% or lower.
HOW TO USE
COMFORT FIT
1. Adjust the strap at both ends until you
can easily and comfortably wear the
eye mask. The strap features
hook-and-loop fasteners that attach
to the strap itself.
2. Make sure the eye mask sits
comfortably on your face and that the
fit is not too tight. Loosen the strap if
necessary.
POWER
1. Press and hold the power/mode button for 2 seconds to power on the
eye mask. The "power on" voice prompt will play.
2. Press and hold the power/mode button again to manually turn off the
eye mask. If left on, the eye mask will automatically power off after 15
minutes.
PAIRING
1. To connect your device via Bluetooth
wireless technology, press and hold the
pairing button for 2 seconds. The eye
mask will enter pairing mode and the
LED will start flashing blue.
2. Select "SI MASSAGING EYE MASK" from
your device's Bluetooth menu to
connect the eye mask. The "Bluetooth
connected" voice prompt will play and
the LED will remain lit for 5 seconds.
3. To disconnect the eye mask and return
to built-in soundscapes, press and hold
the pairing button for 1 second.
®
WHAT YOU GET
a. RealTouch™ Eye Massager
b. USB-C to USB-A charging cable
Power/Mode
USB-C Port
Charging
LED
Indicator
Heat/Cool/
Compression
Intensity
a.
GETTING STARTED
CHARGING
1. Plug the USB-C side of the charging
cable into the port located on the top of
the eye mask.
2. Plug the USB-A side of the charging cable
into a power adapter (not included).
3. Plug the power adapter into a wall outlet.
The white LED on the eye mask will flash
during charging.
4. Unplug the eye mask when it is fully
charged. The LED will stop flashing and
remain lit. It may take up to 3 hours to fully
charge the eye mask.
Note: The eye mask cannot be used while
charging. When the battery is low, a voice
prompt will state "low battery" and a red
LED will begin flashing. Recharge the eye
mask to continue use.
MUSIC SETTINGS
1. Press the play/pause
button to play
or pause audio.
2. Press the plus
button to increase the
volume or the minus
button to
decrease the volume. The eye mask
powers on with audio at max volume.
3. To cycle through the built-in
soundscapes, quick press the
pairing/music button while the eye
mask is not paired with another device.
MASSAGE SETTINGS
1. Power on the eye mask to
automatically activate air compression
massage.
2. Quick press the power/mode button to
cycle through the 3 massage modes or
turn off the massage functions.
• Mode 1: air compression only
• Mode 2: air compression and vibration
• Mode 3: vibration only
• Off: disables air compression and
vibration
3. To switch between low and high
massage intensities, press and hold the
hot + cold/intensity button for 1 second.
TEMPERATURE SETTINGS
1. Power on the eye mask to automatically activate alternating hot and
cold therapy.
2. Quick press the hot + cold/intensity button to cycle through the 3 hot +
cold modes or turn off the hot + cold functions.
• Hot + Cold: alternates hot (3 minutes) and cold (2 minutes)
• Cold: remains cold
• Hot: remains hot
• Off: disables hot and cold
Pairing LED Indicator
Pairing/Music
Volume -
Play/Pause
Volume
b.
Advertisement
