Draytek Vigor2865 Quick Start Manual
  1. Manuals
  2. Brands
  3. Draytek Manuals
  4. Network Hardware
  5. Vigor2865 Series
  6. Quick start manual
Draytek Vigor2865 Quick Start Manual

Draytek Vigor2865 Quick Start Manual

35b security firewall
Hide thumbs Also See for Vigor2865:
Table of Contents

Advertisement

Quick Links

Download this manual
Vigor2865
35b Security Firewall
Quick Start Guide
(for Wired Model)
Version: 1.9
Firmware Version: V4.4.3.1
(For future update, please visit DrayTek web site)
Date: December 19, 2023
i

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Vigor2865 and is the answer not in the manual?

Questions and answers

Related Manuals for Draytek Vigor2865

Summary of Contents for Draytek Vigor2865

  • Page 1 Vigor2865 35b Security Firewall Quick Start Guide (for Wired Model) Version: 1.9 Firmware Version: V4.4.3.1 (For future update, please visit DrayTek web site) Date: December 19, 2023...
  • Page 2 Intellectual Property Rights (IPR) Information © All rights reserved. This publication contains information that is protected Copyrights by copyright. No part may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language without written permission from the copyright holders. The following trademarks are used in this document: Trademarks ...
  • Page 3 EU Declaration of Conformity Hereby, DrayTek Corporation declares that the equipment type Vigor2865 is in compliance with EU EMC Directive 2014/30/EU, Low Voltage Directive 2014/35/EU and RoHS 2011/65/EU. The full text of the EU Declaration of Conformity is available at the following internet address: https://fw.draytek.com.tw/Vigor2865/Document/CE/...
  • Page 4 Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. More update, please visit www.draytek.com. *The external power supply used for each product will be model dependent. Manufact...

  • Page 5: Table Of Contents

    1. Package Content ....................1 2. Panel Explanation....................2 3. Hardware Installation ................... 4 3.1 Network Connection ........................4 3.2 Wall-Mounted Installation ......................5 4. Software Configuration ..................6 4.1 Quick Start Wizard for Network Connection................6 5. Customer Service ....................12 Be a Registered Owner ........................

  • Page 6: Package Content

    Take a look at the package content. If there is anything missed or damaged, please contact DrayTek or dealer immediately. Vigor router Quick Start Guide RJ-45 Cable (Ethernet) RJ-11 to RJ-45 Cable (Annex B) RJ-11 to RJ-11 Cable (Annex A) The type of the power adapter depends on the country that the router will be installed.

  • Page 7: Panel Explanation

    Status Explanation The router is powered off. Blinking The router is powered on and running normally. WAN2 Internet connection is ready. Internet connection is not ready. Blinking The data is transmitting. The QoS function is active. The QoS function is inactive. USB1~2 USB device is connected and ready for use.
  • Page 8 The port “WAN2 / P6” is switchable. It can be used for LAN connection or WAN connection according to the settings configured in WUI. Interface Description Factory Reset Restore the default settings. Usage: Turn on the router (ACT LED is blinking). Press the hole and keep for more than 5 seconds.

  • Page 9: Hardware Installation

    This section will guide you to install the router through hardware connection and configure the router’s settings through web browser. Before starting to configure the router, you have to connect your devices correctly. Connect the DSL interface to the land line jack with a DSL line cable, or Connect the cable Modem/DSL Modem/Media Converter to the WAN port of router with Ethernet cable (RJ-45).

  • Page 10: Wall-Mounted Installation

    Vigor router has keyhole type mounting slots on the underside. Drill two holes on the wall. The distance between the holes shall be 168mm. Fit screws into the wall using the appropriate type of wall plug. The recommended drill diameter shall be 6.5mm (1/4”). Note When you finished about procedure, the router has been mounted on the wall firmly.

  • Page 11: Software Configuration

    To access Internet, please finish basic configuration after completing the hardware installation. The Quick Start Wizard is designed for you to easily set up your router for Internet access. You can directly access the Quick Start Wizard via Web Configurator. Make sure your PC connects to the router correctly. Note You may either simply set up your computer to get IP dynamically from the router or set up the IP address of the computer to be the...
  • Page 12 Now, the Main Screen will pop up. Click Wizards>>Quick Start Wizard. If your router can be under an environment with high speed NAT, the configuration provide here can help you to deploy and use the router quickly. The first screen of Quick Start Wizard is entering login password. After typing the password, please click Next.
  • Page 13 On the next page as shown below, please select the WAN interface that you use. If DSL interface is used, please choose WAN1; if Ethernet interface is used, please choose WAN2; if 3G USB modem is used, please choose WAN5 or WAN6. Then click Next for next step.
  • Page 14 Choose WAN1 as WAN Interface and click the Next button; you will get the following page. After finished the above settings, simply click Next.
  • Page 15 Please manually enter the Username/Password provided by your ISP. Then click Next for viewing summary of such connection. Click Finish. A page of Quick Start Wizard Setup OK!!! will appear. Then, the system status of this protocol will be shown. Now, you can enjoy surfing on the Internet.
  • Page 16 Choose WAN1 as WAN Interface and click the Next button; you will get the following page. Please type in the IP address/mask/gateway information originally provided by your ISP. Then click Next for viewing summary of such connection. Click Finish. A page of Quick Start Wizard Setup OK!!! will appear. Then, the system status of this protocol will be shown.

  • Page 17: Customer Service

    Web registration is preferred. You can register your Vigor router via https://myvigor.draytek.com. & & Due to the continuous evolution of DrayTek technology, all routers will be regularly upgraded. Please consult the DrayTek web site for more information on newest firmware, tools and documents. https://www.draytek.com...

Table of Contents