Page 3
Declaration of Conformity Hereby, DrayTek Corporation declares that the equipment type Vigor2866 is in compliance with Radio Equipment Directive 2014/53/EU, Low Voltage Directive 2014/35/EU and RoHS 2011/65/EU. The full text of the EU Declaration of Conformity is available at the following internet address: https://fw.draytek.com.tw/Vigor2866/Document/CE/...
Page 4
Declaration of Conformity Hereby, DrayTek Corporation declares that the equipment type Vigor2866 is in compliance with the Radio Equipment Regulations 2017 (SI 2017 No.1206, The Electrical Equipment (Safety) Regulations 2016 (SI 2016 No.1101), and The Restriction of the Use of Certain Hazardous Substances in Electrical and Electronic Equipment Regulations 2012 (SI 2012 No.
Page 5
Regulatory Information Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
Page 6
Caution: Any changes or modifications not expressly approved by the grantee of this device could void the user's authority to operate the equipment. Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
Take a look at the package content. If there is anything missed or damaged, please contact DrayTek or dealer immediately. Besides, the content is subject to the real package. 2 sets (Antenna + Extension Base) Vigor Router RJ-45 Cable (Ethernet)
Status Explanation The router is powered off. Blinking The router is powered on and running normally. Internet connection is ready. WAN2 Internet connection is not ready. Blinking The data is transmitting. The QoS function is active. The QoS function is inactive. LTE device is connected and ready for use.
Page 10
The port is connected with 1000Mbps. Right LED The port is connected with 10/100Mbps. LAN P1-P5 The port is connected. Left LED The port is disconnected. Blinking The data is transmitting. The port is connected with 1000Mbps. Right LED The port is connected with 10/100Mbps Interface Description Restore the default settings.
Status Explanation The router is powered off. Blinking The router is powered on and running normally. Internet connection is ready. WAN2 Internet connection is not ready. Blinking The data is transmitting. The QoS function is active. The QoS function is inactive. USB device is connected and ready for use.
Page 12
Wireless function is disabled. It will blink slowly while wireless traffic goes through. ACT and WLAN LEDs blink quickly and Blinking simultaneously when WPS is working, and will return to normal condition after two minutes. (You need to setup WPS within 2 minutes.) The DMZ function is enabled.
Page 13
Interface Description Wireless band will be switched /changed according to the button pressed and released. For example, 2.4G (On) and 5G (On) – in default. 2.4G (Off) and 5G (On) – pressed and released the button once. Wireless LAN ...
Page 14
The port “WAN2 / P6” is switchable. It can be used for LAN connection or WAN connection according to the settings configured in WUI. Connecters for local network devices. LAN P1-P5 Connecter for accessing the Internet. Connecter for installing WLAN antennas. (For ac model) Connecter for a power adapter.
Status Explanation The router is powered off. Blinking The router is powered on and running normally. Internet connection is ready. WAN2 Internet connection is not ready. Blinking The data is transmitting. The QoS function is active. The QoS function is inactive. USB device is connected and ready for use.
Page 16
The port is disconnected. Blinking The data is transmitting. The port is connected with 1000Mbps. Right LED The port is connected with 10/100Mbps Interface Description Wireless band will be switched /changed according to the button pressed and released. For example, ...
Page 17
Connecter for a power adapter. ON/OFF Power Switch.
This section will guide you to install the router through hardware connection and configure the router’s settings through web browser. Before starting to configure the router, you have to connect your devices correctly. (For the hardware connection, we take “ac” model as an example.) Connect the DSL interface to the land line jack with a DSL line cable, or Connect the cable Modem/DSL Modem/Media Converter to the WAN port of router with Ethernet cable (RJ-45).
Vigor router has keyhole type mounting slots on the underside. Drill two holes on the wall. The distance between the holes shall be 168mm. Fit screws into the wall using the appropriate type of wall plug. Note The recommended drill diameter shall be 6.5mm (1/4”). When you finished about procedure, the router has been mounted on the wall firmly.
“ ” “ ” Magnetic antenna must be installed on the extension base before connecting to Vigor router. Extension Base The antenna with an extension base on the Vigor router must be installed correctly. If only one antenna shall be installed, please use the connector (main signal connector) near the power switch.
Assemble the SIM1 and SIM2 with the card cassette. Later insert the cassette into the SIM card slot and the direction of card notch must be on the left side. There are two types of antennas provided for Vigor2865Lac, which must be installed in different locations carefully and correctly.
To access Internet, please finish basic configuration after completing the hardware installation. The Quick Start Wizard is designed for you to easily set up your router for Internet access. You can directly access the Quick Start Wizard via Web User Interface.
Page 23
Now, the Main Screen will pop up. Click Wizards>>Quick Start Wizard. Note The home page will change slightly in accordance with the router you have. Here we take Vigor2866ac as an example. If your router can be under an environment with high speed NAT, the configuration provide here can help you to deploy and use the router quickly.
Page 24
On the next page as shown below, please select the WAN interface that you use. If DSL interface is used, please choose WAN1; if Ethernet interface is used, please choose WAN2; if wireless 2.4G/5G connection is used, please choose WAN3 or WAN4; if 3G USB modem is used, please choose WAN5 or WAN6. Then click Next for next step.
Page 25
Choose WAN1 as WAN Interface and click the Next button; you will get the following page. After finished the above settings, simply click Next.
Page 26
Please manually enter the Username/Password provided by your ISP. Then click Next for viewing summary of such connection. Click Finish. A page of Quick Start Wizard Setup OK!!! will appear. Then, the system status of this protocol will be shown. Now, you can enjoy surfing on the Internet.
Page 27
Choose WAN1 as WAN Interface and click the Next button; you will get the following page. Please type in the IP address/mask/gateway information originally provided by your ISP. Then click Next for viewing summary of such connection. Click Finish. A page of Quick Start Wizard Setup OK!!! will appear. Then, the system status of this protocol will be shown.
Web registration is preferred. You can register your Vigor router via https://myvigor.draytek.com. & & Due to the continuous evolution of DrayTek technology, all routers will be regularly upgraded. Please consult the DrayTek web site for more information on newest firmware, tools and documents. https://www.draytek.com...