Speaka Professional 2799723 Instruction Manual

10
C
Note: Don't
take the
screws out.
11
The product is powered by electricity. In order to avoid burns, fire and electric shock and make sure the safe and correct use
of the system and maintain the longevity of the overall construction and the built-in electronics, please read the instructions
carefully.
· This appliance can be used by children aged from 8 years and above if they have been given supervision or instruction concerning
use of the appliance in a safe way and understand the hazards involved. Children shall not play with the appliance. Cleaning and user
maintenance shall not be made by children without supervision.
· Persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge must not use the appliance,
unless they're under supervision, understand the hazards involved or they have been thoroughly instructed in the use of the
apparatus by a person who is responsible for the safety of these persons.
· Don't leave the cords or plug unorganized in order to prevent tripping hazards.
· Any attempts to reconstruct the construction aren't allowed.
Electrical Safety Instructions
· The appliance is only to be used with the power supply unit provided with the appliance. Alterations of the given power unit aren't
allowed.
· Never operate the system with a damaged power supply cord or plug. If any parts is damaged, please contact your service agent of
purchase for a replacement.
· Never operate the system if it's in moist environment or its electrical components has contact with liquids.
· Don't clean the product while the power is still connected.
· Don't disassemble or replace components while the power is still connected.
· Unplug the appliance when the system isn't in use, and place the power plug out of children reach.
Too long
M-A
M-F
M-C/M-D
M-F
M-G
M-H
Q
Warnings
Instruction Manual
MOTORIZED
WALL-MOUNTED
TV STAND
Item no.: 2799723
Support VESA mount
200x200 300x200 400x200
300x300 400x300 600x200
350x350 400x400 600x400
800x400 800x600
Note: Insert 2 AAA batteries (not included) into the controller prior to adjust the TV Stand.
Adjust the height by pressing the " " and " " button on the remote control. If the TV Stand fails to rise or lower,
please match code between TV Stand and the remote control by following the instruction below
Too Short
M-B
M-F
STEP 2a:
Press the small button on the control box with a paper clip or pencil as shown. The unit stops beeping, then
M-E
press the " " button on the remote control, then you hear consecutive beeps for arround 10 seconds indicating
M-F
the pairing is ongoing. After that, the unit beeps once again, and stop, meaning the pairing is completed.
Long press the "
M-G
again, the default setting is accomplished.
M-H
STEP 2b:
Long press the "
position. When the unit beeps once again, the default setting is accomplished.
Remote Control User Guide
1. UP/DOWN ARROWS
P
Press and hold the "
Note: Remove all surrounding items prior to adjusting the Mount height.
2. Memory Setting
Long press the "
current position has been saved to memory. The "
height.
3. Activate Height Settings
Press the "
corresponding button "
4. Default Setting
Short press the "
To stop it, press the "
5. Reset Mode
Long press the " " button for 3 seconds until you hear a beep, and the mount starts to move downwards. Then the
mount will move upwards a little bit when reaching the lowest position and stop. The system resets successfully when
the unit beeps twice.
6. To Unpair a Remote Control
Press the small button on the control box with a paper clip or pencil as how you pairing the remote control. After
hearing a beep, hold and press the button for 5 seconds until you hear a beep again, which indicates the unpairing is
completed.
Note: There is no function instruction to the "
Disposal:
The product with this mark indicates that this product shouldn't be disposed with other household wastes
throughout the EU. To prevent possible harm to the environment or human health from uncontrolled waste
disposal, recycle it responsibly to promote the sustainable reuse of material resources. To return your used
device, please use the local recycle service or contact your point of purchase to withdraw the product.
1. Can't operate
There are 7 possibilities:
· Incorrect operation. Check if the unit beeps once after pressing a button. If so, please follow the instructions found in the manual
to properly operate the mount.
· The system of Mount may be error. Check if the unit beeps three times after pressing a button. If so, please reset the system.
· The system may be overheating. Check if the unit beeps four times after pressing a button. If so, allow the unit to cool down
(about 30 minutes).
· The AC/DC end of the power cord may be unplugged/disconnect from the outlet/mount. Check the connection to ensure the
unit is powered.
· The operating distance may be too far and not in range of the mount. Using the remote control within 30 feet (10m) from
the Mounts.
· The batteries in the remote control may be low or dead. Replace the batteries.
· The remote control may be broken. Check to see if the indicator LED found on the remote lights when a button is pressed.
If not, contact your place of purchase for a replacement.
2. The TV mount stops moving during operation and emits a long beep.
· Remove all surrounding items.
· The weight of TV may exceed the maximum weight limitation of the mounting system.
· The motor wire may be broken. Reset the system. If the problem still exists, contact your place of purchase for replacement.
3. The TV mount is making an abnormal noise or sound.
· Check all power connections and reset the system. If the unit continues to make an abnormal noise, please contact your place


of
purchase for a replacement.
max.
100"
254 cm
MAX
Default Setting & Pairing the Remote to the Mount
STEP 1: Everytime the mount is powered on, the unit beeps consecutively, indicating the
mount is ready for default setting.
If it is the first time you turn on the mount, you should pair the remote to the mount first then start
default setting. See the STEP 2a below.
If it isn't the first time you turn on the mount, you should start default setting, and see the STEP 2b
below.
" button. The mount automatically retract to lowest position. When the unit beeps once
" button. The unit stops beeping. Then, the mount automatically retract to the lowest
" button to raise the Mount. Press and hold the"
" or " " button for 3 seconds until you hear a beep,
indicating that the
" "
" or " " button and the mount will automatically get to the position saved in the
" or " ".
" button and the mount will automatically retract to the lowest position.
" button again.
"and " "
buttons.
Troubleshooting Guide
120kg 120kg
(264lbs) (264lbs)
RATED RATED
" button to lower the Mount.
" buttons can each store a