Table of Contents
Advertisement
Programming
the remote control to operate a
cable converter box, satellite receiver, VCR,
DVD player, or HTIB (home theater in a box)
Your Toshiba TV remote control is preprogrammed
to operate most
Toshiba devices. To program your TV remote control to operate a
non-Toshiba device (or a Toshiba device that it is not preprogrammed
to operate), follow the steps below. For details on using the remote
control to operate the device, see page 19.
1. In the remote control code table (below and on the next page),
find the code for your device. If more than one code is listed, try
each one separately until you find one that works.
2. Set the Device Switch to the type of device you are programming
the remote control to operate -- CBL/SAT (for a cable converter
box or satellite receiver), VCR (for a VCR or TV/VCR combo),
or DVD (for a DVD player or HTIB [home theater in a box]).
3. While holding down RECALL, press the Channel Number
buttons to enter the 3-digit code for your device.
4. To test the code, turn on the device, point the remote control at
it, and press POWER. See notes at right.
• If the correct code was entered, the device will turn off:
• If the device does not respond, repeat steps 1 - 4 using
another code.
• If the device does not respond to another code, you will need
to use the remote control that came with the device.
5. Remember to set the Device Switch back to TV to control the TV.
6. For future reference, write down the code(s) you used:
DEVICE
CODE
DEVICE
CODE
RECALL
Note."
•/n addition to POWER confirm that all
necessarykeys on the TVremote control
operate your device ff some keys are not
operational,repeat the device code setup
using another code U other codes are listed
foryour device) If, after trying all listed
codes,the necessarykeys do hogoperate
your device, use the device's original remote
controL
• Everytime you change the batteries,you will
need to reprogram the remote control
• Some newer VCRsrespond to either of two
codes TheseVCRshavea switch labeled
"VCR1/VCR2" If your VCRhas thiskind of
switch and doesnot respond to the codes
foryour VCRbrand, set the switch to the
otherpos/don ("VCR1" or "VCR2'? and
reprogram the remote controL
Remote
control
codes
In some cases you may not be able to operate
your device with the TV remote
control.
Your other device may use
a code that is not recognized
by the TV remote
control.
If this happens,
use the device's remote
control.
Cable converter
box
ABC: 061,062,063,
082, 084, 087, 09I,
092, 096, 098
Archer:065,092,097,
099
Cableview:064, 094
Century: 092
Citizen: 090, 092, 097
Contec: 083,085,086,
088, 093, 098
Diamond: 093
Eagle:091
GE: 06I, 062
Gemini: 069, 070, 094
General Instruments:
062, 089, 096
Hamlin: 093
Hitachi: 062,095,096
asco: 097
errold: 062, 069, 07I,
082, 086, 089, 09I,
O96
Magnavox:072,096
Memorex:091,092, 104
Multi Canal: 090
Novavision: 101
Panasonic:08I, 083, 085
Philco: 087
Philips:066, 067, 068,
070, 072, 073, 074,
075, 09t, 092
Pioneer: 076, 077
Proscan:061,062
l_aldio Shack: 092, 097,
O99
RCA: 064, 081
R_atistic:065
Recoton: 102
Samsung:077, 090
ScientificAtlanta: 063,
078,079,080,088,
098, I01, I05
Sears:095
Signature:062
Signature2000:096
Sprucer:081,085
Smrcom: 069, 082, 087,
096, I03, I04
Smrgate:069, 090
Sylvania:095, 100
"IbleView: 0 90
"I?xscan:100
"Ibcom:07I, 084, 085
U. S. Electronics:087,
096, 098
United Cable: 082
Universal:065,092,097,
099, 102, 103
Wards: 096
Satellite receiver
Alpb_tar: 038,059
Chaparral: 034
DISH Network: 057
Drake:020,040,044,
046, 050, 053
Echostar:018,041,051
ExpressVu: 057
Fujitsu: 027
GE: 008, 009, 013
General Instruments:
010, 011,012, 022,
023, 031,049
Hitachi: 033
Hughes: 033
Hughes Network
Systems: 019
lntersat: 048
Janeil: 027
JVC: 017, 057
Kenwood: 029
Magnavox:060
Optlmus: 058
Pansau 036, 052
Primestar: 015,042
Proscan:008, 009, 013
l_aldioShack: 022,023,
O30
(Continued)
17
Advertisement
Table of Contents
