Page 1
The model number and serial number are on the back of your TV. Record these numbers in the spaces below. Refer to these numbers whenever you communicate with your Toshiba dealer about this TV. Model: Serial No.: 5/10/05, 12:39 PM...
Dear Customer, Thank you for purchasing this Toshiba TV. This manual will help you use the many exciting features of your new TV. Before operating the TV, please read this manual completely, and keep it nearby for future reference. Safety Precautions...
Important Safety Instructions 1) Read these instructions. 2) Keep these instructions. 3) Heed all warnings. 4) Follow all instructions. 5) Do not use this apparatus near water. 6) Clean only with dry cloth. 7) Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.
Page 4
Care For better performance and safer operation of your TOSHIBA TV, follow these recommendations and precautions: 29) Always sit approximately 10–25 feet away from the TV and as directly in front of it as possible. The picture can appear dull if you sit too far to the left or right of the TV, or if sunlight or room lights reflect on the screen.
Page 5
Important notes about your DLP 1) The light source for this TV is a projection lamp unit with a limited service life. When the lamp wears out, the picture may become dark or black, or the lamp may fail, at which time you must replace the lamp unit.
Important Safety Information ... 2-5 Introduction ... 7 Welcome to Toshiba ... 7 Exploring your new TV ... 7 Connecting your TV ... 8 Connecting an antenna or cable TV ... 8 Connecting a VCR ... 9 Connecting a cable converter box ... 9 Connecting a cable converter box and VCR ...
Thank you for purchasing this Toshiba TV, one of the most innovative DLP projection TVs on the market. The goal of this manual is to guide you through setting up and operating your Toshiba TV as quickly as possible. This manual applies to models 46HMX85, 52HMX85, and 62HMX85.
Component video cables come in sets of three, and are for use with video equipment that has component video output. (ColorStream Toshiba’s brand of component video.) HDMI cable is for use with video equipment that has an HDMI output (type A connector) (see page 15).
Connecting a VCR This connection allows you to watch local channels and video programs, play or record on the VCR while watching TV, and record from one channel while watching another channel. You will need: • two coaxial cables • one set of standard A/V cables From Cable Box or Antenna Stereo VCR IN from ANT OUT to TV...
Connecting a cable converter box and VCR This connection allows you to watch and record basic and premium cable channels, watch videotapes, and record one channel while watching another channel. To watch basic cable and use the TV’s features, select ANT-1. To view premium channels or record with the VCR, select ANT-2, tune the TV and VCR to channel 3 or 4 (whichever channel is vacant in your area), and use the converter box to change channels.
Connecting a DVD player or satellite receiver and a VCR This connection allows you to watch DVD/satellite, VCR, and TV programs, and record one TV channel while watching another channel. You will need: • two (or three, if satellite receiver is used) coaxial cables •...
TV programs. ® Your TV has ColorStream (component video) inputs. Connecting your TV to a DVD player with component video (such as a Toshiba DVD player with ColorStream and realism. – To record one TV program while watching another TV program, tune the VCR to the channel to record, and tune the TV to the channel to watch.
Connecting a DTV receiver/set-top box with ® ColorStream (component video) and a VCR This connection allows you to watch DTV (digital TV), VCR, and TV programs, and record DTV (composite video only) and TV programs. Your TV has ColorStream (component video) inputs. Connecting your TV to a DTV receiver with component video can greatly enhance picture quality and realism.
Connecting two VCRs This connection allows you to record (dub/edit) from one VCR to another VCR while watching a videotape. You also can record from one TV channel while watching another TV channel. You will need: • two coaxial cables •...
Connecting an HDMI™ or a DVI device to the HDMI inputs The HDMI inputs on your TV receive digital audio and uncompressed digital video from an HDMI device or uncompressed digital video from a DVI device. These inputs are designed to accept HDCP material in digital form from EIA/CEA-861/861B–...
Connecting an audio system This connection allows you to use an audio amplifier and external speakers and adjust the audio level by using the TV’s remote control. To control the audio, turn on the TV and the stereo amplifier, and turn off the built-in speakers (see “Turning off the built-in speakers”...
Using the remote control Preparing the remote control for use Your Toshiba TV remote control has one dedicated TV mode and five universal modes: VCR, Cable/SAT, DVD, Audio1, and Audio2. The target devices and default devices being programmed for each mode...
Remote Control functional key chart Toshiba TV Key Label (TV) (CBL/SAT) (CBL/SAT) LIGHT Lights the remote control keys, and toggles between enabled and disabled Illumination mode. SLEEP Sleep timer --- POWER Power Power Digit 1 Digit 1 Digit 2 Digit 2...
Page 19
Toshiba TV Key Label (TV) TV/VCR AM/FM DISC STOP REC** POP CH POP channel up/down SPLIT POP Split POP DIRECT CH POP Direct ch FREEZE Still picture SWAP POP Swap CH SCAN Ch scan SOURCE POP Source Notes: • “---” will send nothing.
Programming the remote control for use with your audio/video devices Device code setup 1. Refer to the Device code table on pages 22 – 23 to find the code for the brand of your device. If more than one number is listed, try each one separately until you find the one that works.
Using the volume lock feature (8000) For the TV, CABLE/SAT, VCR, and DVD modes, the volume controls (VOL yz and MUTE) can be programmed (locked) to the selected device mode. This feature does not apply to the AUDIO1/2 modes. For example, to lock the volume controls to always jump to the CABLE/SAT mode: 1.
Learning about the remote control The buttons used for operating the TV only are described here. For a complete list of the remote control’s functions, see the “Remote Control functional key chart” on pages 18–19. turns the TV on and off. POWER Note: If the Quick Restart feature is in OFF mode, it can take up to several seconds for...
Setting up your TV Turning on the TV Press POWER on the remote control or TV. The Red LED indicator on the TV will be illuminated. Press POWER again to turn off the Learning about the menu system After you have installed the batteries and programmed the remote control, you will need to set some preferences on the TV by using the menu system.
Changing the on-screen display language You can choose from three different languages (English, French, and Spanish) for the on-screen display of adjustment menus and messages. To select a language: 1. Press MENU, and then press x or • until the SET UP menu appears.
Adding channels to the TV’s memory When you press Channel y or z, your TV will stop only on the channels stored in the TV’s channel memory. Follow the steps below and on the next page to program all active channels into the TV’s memory.
Adding and erasing channels manually After you have programmed the channels automatically, you can manually add or erase specific channels. To manually add or erase channels: 1. Select the channel you want to add or erase. If you are adding a channel, you must select the channel using the Channel Number buttons.
Using the TV’s features Adjusting the channel settings Switching between two channels using Channel Return The Channel Return feature allows you to switch between two channels without entering an actual channel number each time. 1. Select the first channel (or video mode) you want to view. 2.
Page 30
3. Press ENTER to display the FAVORITE CH menu. CH INPUT will be highlighted. FAVOR I TE CH – – – I NPUT – – – – – – – – – – – – – – – – – – –...
Labeling channels Channel labels appear above the on-screen channel number display each time you turn on the TV, change a channel, or press RECALL. You can choose any four characters to identify a channel. To create channel labels: 1. Press MENU, and then press x or • until the CUSTOM menu appears.
Viewing the wide-screen picture formats (480i, 480p, and 1080i signals only) You can view 480i, 480p, and 1080i format programs in a variety of picture sizes—Natural, TheaterWide 1, TheaterWide 2, TheaterWide 3, and Full. (The Full picture size is not selectable for 1080i format programs.) The way the image displays in any of the picture sizes will vary depending on the format of the program you are viewing.
Page 33
TheaterWide 1 picture size (For 4:3 format programs) • The picture is non-uniformly enlarged—the center of the picture remains close to its original proportion, but the left and right edges are stretched wider to fill the screen. • A small part of the picture at the top and bottom is hidden;...
Scrolling the TheaterWide (TheaterWide 2 and 3 only) 1. Press PIC SIZE to select the TheaterWide 2 or 3 mode. 2. Press MENU, and then press x or • until the PICTURE menu appears. 3. Press y or z to highlight PICTURE SCROLL. P CTURE MODE SPORTS...
Using the AUTO ASPECT feature When the AUTO ASPECT feature is set to ON and the TV receives a 480i signal, the picture size is automatically selected (as described in the following table). Aspect ratio of signal source 4:3 Normal 16:9 Full 4:3 Letter box Not defined (no ID-1 data)*...
Using the POP double-window feature The POP (picture-out-picture) feature splits the screen into a double window that allows you to watch two programs at the same time. The POP program can come from a TV broadcast or an external source, such as a VCR.
Swapping the main and POP pictures While you are viewing the POP double-window feature, you can press SWAP to swap the position of the main and POP pictures. Switching the speaker sound (main or POP program) Press x or • while you are using the POP feature to switch the sound (main or POP) that is output from the speakers.
Double-Window aspect ratio The Double-Window feature displays each picture according to its input signal aspect ratio, as illustrated below. 480i 480i Using the programmed channel search function You can use the programmed channel search function to quickly scan the channels you programmed into the TV’s memory (page 27). 1.
Using the favorite channel search function You can use the favorite channel search function to quickly scan your favorite channels (see “Programming your favorite channels” on page 29). 1. Press FAVORITE. The TV automatically enters multi-window mode, and begins a twelve-picture scan of your favorite channels in the multi-window.
Using the LOCKS menu The LOCKS menu includes the V-Chip, CH Lock, Video Lock, and New PIN Code functions. You can use these functions after entering the correct PIN code. Entering the PIN code 1. Press MENU, and then press x or • until the LOCKS menu appears.
ENABLE BLOCKING 1. From the LOCKS menu (page 40), press z or y to highlight V- CHIP, and then press ENTER. The V-CHIP menu appears. 2. Press z or y to highlight ENABLE BLOCKING, and then press ENTER. 3. Press y or z to select ON or OFF. ON : To enable your setting (Lock) OFF: To release your setting (Unlock) Note: The CH LOCK function is not affected by this setting.
MPAA RATING (Independent rating system for movies) 1. From the V-CHIP menu (page 41), press z or y to highlight MPAA RATING, and then press ENTER. The MPAA RATING menu appears. 2. Press y or z to highlight MPAA RATING. 3.
Unlocking programs temporarily 1. If you try to watch a TV program that exceeds the rating limits you set, the TV enters program lock mode. After 4 seconds, the TV automatically starts the favorite channel search function (page 39). You can either unlock the program temporarily (see steps 2– 4 below) or select an unlocked program to watch.
Page 44
To unlock individual channels: 1. From the LOCKS menu, press y or z to highlight CH LOCK, and then press ENTER. The CH LOCK menu appears. 2. Press yzx • to highlight the channel you want to unlock, and then press ENTER. CH LOCK –...
Locking the video inputs With the VIDEO LOCK feature, you can lock the input sources (Video 1, Video 2, Video 3, ColorStream HD1, ColorStream HD2, HDMI 1, HDMI 2*) and channels 3 and 4. You will not be able to select the input sources with the TV/VIDEO, INPUT, or Channel buttons unless you set the VIDEO LOCK feature to OFF.
Adjusting the picture Selecting the picture mode You can select your desired picture type from four picture modes: Sports, Standard, Movie, and Preference. Mode Picture Quality Sports Bright and dynamic picture (factory setting) Standard Standard picture setting (factory setting) Movie Movie-like picture setting (factory setting) Preference Your personal preferences*...
Selecting the color temperature You can change the quality of the picture by selecting from three preset color temperatures: cool, medium, and warm. Mode Picture Quality cool bluish medium neutral warm reddish To select the color temperature: 1. Press MENU, and then press x or • until the PICTURE menu appears.
Saving your new preferences You can save the PICTURE settings you adjusted (contrast, brightness, color, tint, sharpness, color temperature, and CableClear DNR) in the picture PREFERENCE mode in the PICTURE SETTINGS menu. To save your new preferences: 1. Press MENU, and then press x or • until the PICTURE menu appears.
Selecting the lamp mode You can select either HI BRIGHT or LOW POWER lamp mode. The HI BRIGHT mode is useful for situations where additional picture brightness is desired (such as in a room with bright lighting). The LOW POWER mode reduces wear on the projection lamp. Using this mode should result in longer lamp life.
Selecting the video input source Press INPUT on the remote control or TV/VIDEO on the TV front panel to view a signal from another device connected to your TV, such as a VCR or DVD player (see illustrations below). You can select ANT 1, VIDEO 1, VIDEO 2, VIDEO 3, ColorStream HD1, ColorStream HD2, HDMI 1, HDMI 2*, or ANT 2, depending on which input jacks you used to connect your devices (see “Connecting your TV”...
Using the closed caption feature The closed caption feature has two options: • Captions—An on-screen display of the dialogue, narration, and sound effects of TV programs and videos that are closed captioned (usually designated “CC” in program listings). • Text—An on-screen display of information not related to the current program, such as weather or stock data (when provided by individual stations).
Setting the ON timer To set the ON timer to turn on the TV automatically: 1. Press MENU, and then press x or • until the CUSTOM menu appears. 2. Press y or z to highlight ON TIMER, and then press ENTER. 3.
Setting the clock To set the clock: 1. Press MENU, and then press x or • until the SET UP menu appears. 2. Press y or z to highlight CLOCK SET, and then press ENTER. 3. Press the Number buttons (0–9) to enter the correct time. The clock operates on a 24-hour cycle.
Adjusting the sound Muting the sound Press MUTE to temporarily reduce (1/2 MUTE) or turn off (MUTE) the sound. While the sound is off, the screen will display “1/2 MUTE” or “MUTE” in the lower right corner. Every time you press MUTE, the mute mode will change in the following order.
Using the WOW™ surround sound feature WOW is a special combination of SRS Labs audio technologies that creates a thrilling surround sound experience with deep, rich bass from stereo sound sources. Your TV’s audio will sound fuller, richer, and wider. WOW consists of three features: SRS 3D, FOCUS, and TruBass.
Virtual surround sound feature allows you to enjoy virtual surround sound from the TV’s speakers. This feature applies to Models 52HMX85 and 62HMX85 only. • If you connect a device (a game console, a DVD player or a DTV receiver, etc.) with analog audio output to the standard (analog)
Highlight OFF in step 3 above. Resetting your audio adjustments The RESET function returns your audio adjustments to the following factory settings: Bass ... center (50) Treble ... center (50) Balance ... center (0) To reset your audio adjustments: 1. Press MENU, and then press x or • until the AUDIO menu appears.
Turning off the built-in speakers Use this feature to turn off the TV’s built-in speakers when you connect an audio system (see “Connecting an audio system” on page 16). To turn off the built-in speakers: 1. Press MENU, then press x or • until the AUDIO menu appears.
Selecting the background of the menu display You can change the background of the menu display by selecting from two preset backgrounds: shaded and solid (gray). To select the background: 1. Press MENU, and then press x or • until the CUSTOM menu appears.
(LED Indication 3; page 64). See “LED indications” on page 64. To obtain a replacement lamp unit: Locate a Toshiba parts distributor by directing your web browser to www.toshiba.ca. Click “Home Entertainment,” and then click “Support.”...
How to replace the lamp unit Required tools: Manual Phillips screwdriver; gloves. Optional tool: 5/32” or 4mm Allen wrench. 1. Turn off the TV and unplug the power cord. WARNING: Eye damage may result from directly viewing the light produced by this lamp.
Page 62
How to replace the lamp unit (continued) 5. Grasp the lamp unit handle and gently pull the lamp unit straight out of the TV. Set the old lamp unit aside (see “Lamp unit disposal” on page 64). 6. Carefully insert the new lamp unit straight into the TV until it is fully seated.
Page 63
• Dark picture • TV will not turn on If, after repeating steps 1–9, the problem still exists: Locate the nearest Toshiba authorized service depot by directing your web browser to www.toshiba.ca; click “Home Entertainment,” and then click “Support.” #01E60-64_46/52/62HMX85...
Turn the POWER OFF and then ON again. If the problem persists, replace the lamp unit (see pages 61–63). If the problem still persists, contact a Toshiba Authorized Service Center. Turn the POWER OFF and unplug the power cord. If the problem persists, contact a Toshiba Authorized Service Center.
• This model may not be compatible with features and/or specifications that may be added in the future. WARNING: RISK OF ELECTRIC SHOCK! Never attempt to service the TV yourself. Opening and removing the covers may expose you to dangerous voltage or other hazards. Refer all servicing to a Toshiba Authorized Service Center. Television System NTSC standard...
Troubleshooting Before calling a service technician, please check the following table for a possible cause of the symptom and some solutions. Symptom TV will not turn on No picture or too dark No picture, no sound No sound, picture OK Poor picture, sound OK Poor reception of broadcast channels Cannot receive above channel 13...
Page 67
Troubleshooting (continued) Symptom Cannot access signal input sources (Video1, Video2, Video3, ColorStream HD1/HD2, HDMI1/2) and/or Channels 3 and 4. Picture and sound are out of sync #01E65-68_46/52/62HMX85 Black (E) 46/52/62HMX85 Solution • Check the VIDEO LOCK feature. (See page 45.) As with all products that contain a digital display, in rare instances, when viewing certain content (e.g..
Read this owner’s manual thoroughly before operating this DLP Television. Register your DLP Television online at www.toshiba.ca as soon as possible. By registering your DLP Television you will enable TCL to bring you new products specifically designed to meet your needs and help us to contact you in the unlikely event a safety notification is required.
Index A/V cables (standard) ... 8 ANT 1/2 ...26 Antenna cables (coaxial) ... 8 AUDIO OUT sound, selecting ... 58 Audio system connection ... 16 Auto aspect ...35 Auto favorite ... 39, 43 Auto power off ...59 BACKGROUND selection ...59 Back of the TV ...
Page 70
Notes #01E70-71_46/52/62HMX85 5/10/05, 12:40 PM Black (E) 46/52/62HMX85...
Page 71
Notes #01E70-71_46/52/62HMX85 5/10/05, 12:40 PM Black (E) 46/52/62HMX85...
Page 72
VANCOUVER: 22171 FRASERWOOD WAY, RICHMOND, B.C., V6W 1J5, CANADA – TEL: (604) 303-2500 MANUFACTURED BY CableClear, ColorStream, StableSound, and TheaterWide are registered trademarks of Toshiba America Consumer Products, L.L.C. SurfLock is a trademark of Toshiba America Consumer Products, L.L.C. PRINTED IN USA...