1. Manuals
  2. Brands
  3. Sukup Manuals
  4. Farm Equipment
  5. 5K Commercial Paddle Sweep
  6. Owner's installation & operations manual

Sukup 5K Commercial Paddle Sweep Owner's Installation & Operations Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
5K Commercial Paddle Sweep
Owner's Installation & Operation Manual
D
ATES
06/04/2020 – Updated sump switch installation instructions ................................................................................ 31
Updated wear track & parking plate installation instructions ..................................................... 33-34
Updated operating instructions ................................................................................................. 35-36
Updated pusher gearbox lubrication instructions ........................................................................... 43
04/24/2020 – Updated/added center sump dimensions drawings ..................................................................... 9-10
Updated carrier wheel installation instructions .......................................................................... 24-25
Added instructions for pusher carrier wheels assy. installation ..................................................... 27
Updated paddle chain installation instructions ............................................................................... 28
Added instructions for preparing speed reducer for installation ..................................................... 29
Added instructions for installing switch for flush-floor sump .......................................................... 31
Added instructions for installing main power box & control panel .................................................. 31
Added Software Manual ............................................................................................................ 37-41
Updated/added sweep layout drawings .................................................................................... 46-51
Updated wiring diagrams........................................................................................................... 52-61
Updated/added drawings & parts lists ..................................................................... 72-75, 78, 90-91
12/03/2019 – Changed name throughout from Medium Duty Paddle Sweep
Updated sump layout drawings ................................................................................................. 13-15
Manual L14359M
06/04/2020
Sweeps 4,000 to 6,000 bph
Sukup Manufacturing Co.
1555 255th Street, Box 677
Sheffield, Iowa, USA 50475-0677
Phone: 641-892-4222
Website: www.sukup.com
Fax: 641-892-4629
E-mail: info@sukup.com
R
EVISIONS
© Sukup Manufacturing Co.
P
AGES

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the 5K Commercial Paddle Sweep and is the answer not in the manual?

Questions and answers

Related Manuals for Sukup 5K Commercial Paddle Sweep

Summary of Contents for Sukup 5K Commercial Paddle Sweep

  • Page 1 5K Commercial Paddle Sweep Sweeps 4,000 to 6,000 bph Owner's Installation & Operation Manual Sukup Manufacturing Co. 1555 255th Street, Box 677 Sheffield, Iowa, USA 50475-0677 Phone: 641-892-4222 Fax: 641-892-4629 Website: www.sukup.com E-mail: info@sukup.com ATES EVISIONS AGES 06/04/2020 – Updated sump switch installation instructions ................31 Updated wear track &...

  • Page 2: Table Of Contents

    Refer to bill of lading. Save all paperwork and documentation furnished with the power sweep. DISCLAIMER: Bin sweeps will vary in performance based on grain condition and condition of bin floor. Any capacities provided by Sukup Manufacturing Co. are based on dry, clean corn and ideal conditions.

  • Page 3: Limited Warranty

    Limited Warranty...

  • Page 4: Safety

    Sukup Manufacturing Co. via mail at PO Box 677, Sheffield, Iowa USA, 50475; by phone at 641-892-4222; or by e-mail at info@sukup.com. It is the responsibility of the owner/operator to know what specific requirements, precautions, and work hazards exist.
  • Page 5 Safety To avoid electric shock or electrocution, all WARNING: Metal is slippery when wet. To equipment must be properly wired and grounded avoid falls, never carry items if climbing on according to electrical codes. Have unit wired by bin. Maintain secure hand and foothold if qualified electrician.
  • Page 6 To order a replacement decal or shield at no charge, contact your dealer or Sukup Manufacturing Co., Box 677, Sheffield, IA USA 50475. If replacement is necessary, make sure location for decal is free from grease, oil and dirt.
  • Page 7 Safety Decal Placement for 5K Commercial Paddle Sweep Fig. 1 shows placement of decals for 5K Commercial Paddle Sweep. If decals are missing or illegible, please order and affix replacements as described on this and previous page. Fig. 1...

  • Page 8: Assembly Instructions

    Preparation for Installation on Flush Floor Installation of Sukup 5K Commercial Paddle Sweep requires pre-installation of a center sump if used on a flush floor. Fabricate sump frame as shown in Fig. 2. Consult bin pad requirements and qualified engineer for dimensions A through E, which vary with bin size.
  • Page 9 Assembly Instructions Installation Install center sump by fully welding top lip of sump to sump frame. Plug-weld holes in sump to sump frame. Cast sump and frame in concrete. Consider conduit exit direction. Leave void in concrete to allow for conduit. See Figs. 3 and 4. Fig.
  • Page 10 Assembly Instructions See Figs. 5 & 6 for sump bottom flange dimensions and hole patterns depending on sump size. Fig. 5 – Hole Pattern 1 for 16” sump (left) & 24” sump (right) Fig. 6 – Hole Pattern 2 for 16” sump (left) & 24”...
  • Page 11 Assembly Instructions Install sweep support cross, sump conduits and guards in center sump as shown in Fig. 8. Fig. 8 – Installing center sump support cross, conduits & guards CROSS-SECTION VIEW OF SUMP Prepare drive housing by removing covers, rear brace and pivot tube. See Fig. 9. If slip ring will be used (for zero-entry operation of sweep), discard slip ring plate.
  • Page 12 Assembly Instructions Attach drive unit to center sump as shown in Fig. 10. Fig. 10 – Attaching drive unit to center sump Preparation for Installation on Full Floor Install drag conveyor as shown in Drag Conveyor Assembly and Owner’s Manual, L2502. Ensure there is at least 53”...
  • Page 13 Assembly Instructions Find exact center of bin on unload conveyor and mark the spot. See Fig. 12. Mark centers of intermediate sumps according to applicable layout drawing (below or on following pages). Cut conveyor covers as shown in Fig. 12. Fig.
  • Page 14 Assembly Instructions 54’ bin 60’ bin Fig. 14 – Sump layouts for 54’ & 60’ dia. bins 72’ bin 75’ bin 78’ bin Fig. 15 – Sump layouts for 72’, 75’ & 78’ dia. bins...
  • Page 15 Assembly Instructions 90’ bin 105’ Fig. 16 – Sump layouts for 90’ & 105’ dia. bins...
  • Page 16 Assembly Instructions Position center sump over conveyor with center hole at exact center of bin. See Fig. 17. Adjust six (6) supports at bottom of sump to correct height. Staggered holes provide adjustment for level installation on uneven concrete. See Detail A. Remove fasteners from four corners of sump.
  • Page 17 Assembly Instructions Preparing Intermediate Sumps Remove sump top and two pull rod attachment bolts. See Fig. 18. Remove 3/8” hardware from four corners of sump. Loosen two pull-rod carriage bolts but do not remove. Fig. 18 – Preparing intermediate sumps Sumps closest to center sump (one on each side) are independent intermediate sumps.
  • Page 18 Assembly Instructions Place sumps on conveyor according to applicable layout drawing. See Pages 13-15. Conveyor covers should go on top of sump flanges as shown in Fig. 20. Run pull rods through sumps. Connect pull rods end-to-end using coupling shafts provided. Bolts must be parallel to conveyor to avoid interference.
  • Page 19 Assembly Instructions Install a sweep parking stand on each side of center sump. See Fig. 22. Secure each stand to floor with four concrete anchors. Fig. 22 – Attaching sweep stands If sweep will be used with slip-ring for zero-entry operation, install junction box under parking stand on opposite side of sweep’s parked location.
  • Page 20 Assembly Instructions SWEP0157 60’ 04/16/2019 RTO 72’ 75’ 78’ Fig. 24 – Carrier wheel & floor bridging locations for 60’, 72’, 75’ & 78’ dia. bins 90’ 105’ Fig. 25 – Carrier wheel & floor bridging locations for 90’ & 105’ dia. bins...
  • Page 21 Assembly Instructions Fig. 26 shows assembly of bridging supports and location of floor support bridging in relation to carrier wheel travel path and centerline of bin. “Fingers” of holder should cover square bar and loosely grip tops of floor supports. Fig.
  • Page 22 Assembly Instructions Prepare drive housing for installation as shown on Page 11. Install drive housing as shown in Fig. 29, bolting plates together using hardware provided. Fig. 29 – Drive housing installation Connect head section to drive housing by inserting pivot tube through slots in drive housing and bolting pivot tube into place.
  • Page 23 Assembly Instructions Attach grain deflector to head section using two 3/8 x 1” bolts and flange nuts. See Fig. 31. Fig. 31 – Attaching grain deflector Attach first body section to head section and inner carrier wheels as shown in front and back views of Fig.
  • Page 24 Assembly Instructions Starting with first rear carrier wheel, turn bottom portion so that alignment tabs marked “1” are aligned. See Fig. 33. Secure with two 1/2” locking bolts. For second wheel, align tabs marked “2”, and so forth. NOTE: These instructions apply to sweeps in bins up to heights listed in Table 1. For extra-tall bins, see next page.
  • Page 25 Assembly Instructions On sweeps in extra-tall bins (See sweep layout Figs. 58, 60, 62, 64, 66 and 68), carrier wheels shown with dashed lines get carrier wheel truck with triangle-shaped tab. See drawing at left in Fig. 34. Those shown with solid lines in sweep layout drawings referenced above get carrier wheel truck with flat edge. See drawing at right in Fig.
  • Page 26 Assembly Instructions Remove two pins from front of pusher(s) and use them to connect pushers and carrier wheels to sweep at locations shown in sweep layout drawings. See Fig. 36. PUSHER PINS Fig. 36 – Attaching pusher(s) Pusher Chain Installation Remove outer chain cover.
  • Page 27 Assembly Instructions If bin exceeds height shown in Table 1, install pusher carrier wheels assembly, EP0653, as shown in Fig. 38. Remove four 3/8” nuts under pusher and use to attach carrier wheel assy. PUSHER CARRIER WHEELS ASSY. Fig. 38 – Attaching pusher carrier wheels assy. Remove rear weight bracket from pushers and attach weights as shown in Fig.
  • Page 28 Assembly Instructions Tie rope to paddle chain and pull paddles through return chamber. Rubber side of paddle must face direction of travel. See Fig. 40. Fig. 40 – Pulling paddles & chain through sweep NOTICE: Chain can become twisted if improperly handled. DO NOT turn over a length of chain by twisting one end.
  • Page 29 Assembly Instructions Prepare speed reducer for installation by attaching torque arm brackets as shown in Fig. 42. Remove four bolts from side flange of reducer. Attach torque arm brackets using 3/8” hardware included in parts sack EP0361. NOTE: Multiple sizes are provided. Use those that fit reducer. Attach with 3/8” fine-thread bolts and lock nuts.
  • Page 30 Assembly Instructions Slip Ring Wiring IMPORTANT: Have a qualified electrician wire power to sweep following local electrical codes. Install slip ring by running leads through conduit with lock and then through pivot via flexible conduit supplied by electrician. If bin has full floor, run flex conduit to junction box under floor as shown in Fig. 44, then to controls outside of bin.
  • Page 31 Assembly Instructions If bin has flush floor, thread center sump plug detection switch into switch adapter as shown in Fig. 46. Ensure flat sides of blade will be parallel with grain flow (as if cutting through). Attach adapter to sump as shown in Fig.
  • Page 32 Assembly Instructions Fig. 47 shows slip ring. Use rings 1 to 3 for pushers and rings 4 to 7 for paddle motor/ground. Fig. 47 – Slip ring Re-install drive housing covers. Remove conduit covers from backside of sweep. Attach rigid conduit for pushers as shown in Fig. 48. Use flexible conduit between rigid conduit and pushers.
  • Page 33 Assembly Instructions Installing Wear Track & Parking Plates On full floors, install wear track and parking plates as shown in Figs. 49-51. Use EP0578 wear track for first ring from center; F3405 for carrier-wheel-only track; EC9257 track for pusher wheels. Use EP0617 galvanized parking plates where carrier wheels will rest.
  • Page 34 DO NOT use hex-head screws. NOTE: Fasteners are not supplied, but are available from Sukup (EH0327 for box of 200 rivets, or EP0350 for sack of 100 self-drilling screws). NOTE: If a carrier wheel will follow same path as a pusher, install only pusher wear track.

  • Page 35: Operation

    IMPORTANT: Read this page and entire Software Manual thoroughly before turning on sweep paddles or pushers. When ready to run sweep, touch “Welcome to Sukup Automation” screen shown on Page 37 and log in. On Connected Sweep Systems page, select sweep to be run. Choose Manual Control or Automatic Control.
  • Page 36 Operation Navigate to Auto Mode Settings as shown in Software Manual. Set low current threshold 2 amps above baseline current and set high threshold 2 amps above that. See examples in image below. Setting Low & High Current Thresholds (EXAMPLES) Start running sweep in Automatic mode.

  • Page 37: Software Manual

    Software Manual Software Manual Sukup Automation Solutions™ Zero-Entry Sweep System Touching main page will bring up “Connected Sweep Systems” page. Each panel is capable of running five systems. Select desired system. Manual Control page will appear.
  • Page 38 Software Manual Manual Mode Manual Mode enables independent control of sweep and pusher(s) at user-selected speeds. Set speeds using Sweep VFD Hz and Pusher VFD Hz buttons. Feedback amperage is shown at bottom right of page. There is a User Current option (Wire 21. See Wiring Diagram 110.3) that allows sweep system to monitor a user-provided Current Transducer (CT).
  • Page 39 Software Manual Advanced Settings This page will appear after pressing Advanced Settings button (shown on previous screen). Auto Control Settings for operation in Auto Mode can be accessed and configured, as can Setup Settings for Input Settings (Sweep Current and User Current sensors) and Output Settings (Sweep VFD and Pusher VFD).
  • Page 40 Variable Frequency Drive (VFD). Minimum and maximum outputs can be specified. Pressing Sukup logo at any time will bring up diagnostic pages. This will display all system values like real-time analog and digital statuses. Page at left shows analog signals. Page below...
  • Page 41 Emergency Stop button is located at bottom left of all screens. Pressing it will shut system down and send a signal to other linked equipment controlled by Sukup Automation Solutions to inform of the shutdown. IMPORTANT: Pressing the analog E-stop button...

  • Page 42: Maintenance

    Grease bearings on drive and tail shafts and on pusher wheels. Following are instructions on lubrication of Dodge SC & SCM bearings used on Sukup Paddle Sweeps. Ensure all pushers are functioning properly and all drive wheels are turning, and that all are stopping when sweep is turned off.
  • Page 43 Maintenance Pusher Gearbox Lubrication NOTE: The following pages are from Dodge Quantis RHB Reducer manual. It can be found online at: https://www.baldor.com/mvc/DownloadCenter/Files/MN1618...
  • Page 44 Maintenance...
  • Page 45 Maintenance Inspect wear track to ensure it is still in place and in good condition. Replace any missing fasteners. Inspect all electrical connections, checking for damaged conduits, wires. Before filling bin, position sweep as shown in Fig. 52 so it is just behind intermediate sumps. Fig.

  • Page 46: Layout Drawings

    Layout Drawings See layouts in Figs. 53-68 for recommended pusher locations and order of sweep body sections depending on size of bin. Body sections may be reordered if needed to ensure wheels miss sumps. Fig. 53 shows recommended layout of paddle sweep in 36’ dia. bin up to 28 rings. Fig.
  • Page 47 Layout Drawings Fig. 55 shows recommended layout of paddle sweep in 48’ dia. bin up to 27 rings. Fig. 55 – Paddle sweep layout in 48’ dia. bin ≤ 27 rings tall Fig. 56 shows recommended layout of paddle sweep in 54’ dia. bin up to 27 rings. Fig.
  • Page 48 Layout Drawings Fig. 57 shows recommended layout of paddle sweep in 60’ dia. bin up to 26 rings. Fig. 57 – Paddle sweep layout in 60’ dia. bin ≤ 26 rings tall Fig. 58 shows recommended layout of paddle sweep in 60’ dia. bin with more than 26 rings. Fig.
  • Page 49 Layout Drawings Fig. 60 shows recommended layout of paddle sweep in 72’ dia. with more than 26 rings. Fig. 60 – Paddle sweep layout in 72’ dia. bin > 26 rings tall Fig. 61 shows recommended layout of paddle sweep in 75’ dia. bin up to 25 rings. Fig.
  • Page 50 Layout Drawings Fig. 63 shows recommended layout of paddle sweep in 78’ dia. bin up to 25 rings. Fig. 63 – Paddle sweep layout in 78’ dia. bin ≤ 25 rings tall Fig. 64 shows recommended layout of paddle sweep in 78’ dia. bin with more than 25 rings. Fig.
  • Page 51 Layout Drawings Fig. 66 shows recommended layout of paddle sweep in 90’ dia. with more than 25 rings. Fig. 66 – Paddle sweep layout in 90’ dia. bin > 25 rings tall Fig. 67 shows recommended layout of paddle sweep in 105’ dia. bin up to 24 rings. Fig.

  • Page 52: Wiring Diagrams

    Wiring Diagrams See diagrams on this and following pages for wiring of sweep.
  • Page 53 Wiring Diagrams...
  • Page 54 Wiring Diagrams...
  • Page 55 Wiring Diagrams...
  • Page 56 Wiring Diagrams...
  • Page 57 Wiring Diagrams...
  • Page 58 Wiring Diagrams...
  • Page 59 Wiring Diagrams See Fig. 69. for center sump plug detection switch settings and wiring. NOTE: Switch must be energized while sweep is running. Fig. 69 – Center sump plug switch settings...
  • Page 60 Wiring Diagrams COMMERCIAL SWEEP CONTROLS WIRING GUIDE...
  • Page 61 Wiring Diagrams...

  • Page 62: Dodge Speed Reducer Manual Pages

    Dodge Torque Arm II Speed Reducers NOTE: The following pages are from Dodge Motorized Torque-Arm II Speed Reducers manual, MN1695, dated 12/18. It can be found online at www.baldor.com/mvc/DownloadCenter/Files/MN1695. For warranty information, go to http://www.baldor.com/brands/baldor-dodge/product-support/standard- warranty-information...
  • Page 63 Dodge Torque Arm II Speed Reducers...
  • Page 64 Dodge Torque Arm II Speed Reducers...
  • Page 65 Dodge Torque Arm II Speed Reducers...
  • Page 66 Dodge Torque Arm II Speed Reducers...
  • Page 67 Dodge Torque Arm II Speed Reducers...
  • Page 68 Dodge Torque Arm II Speed Reducers...
  • Page 69 Dodge Torque Arm II Speed Reducers...
  • Page 70 Dodge Torque Arm II Speed Reducers...
  • Page 71 Dodge Torque Arm II Speed Reducers...

  • Page 72: Parts Assemblies

    Parts/Assemblies Parts/Assemblies 5K Commercial Paddle Sweep...
  • Page 73 Parts/Assemblies Paddle Sweep Parts ITEM # DESCRIPTION QTY. PART # Inner front carrier wheel support assy. EP0527 Inner rear carrier wheel support assy. EP0529 Front carrier wheel assy. EP0531 Rear carrier wheel assy. EP0534 Front carrier wheel end support EP0536 Rear carrier wheel end support EP0538 Paddle chain assy.
  • Page 74 Parts/Assemblies Pusher Assembly EP2114, EP2115, EP2116, EP2117...
  • Page 75 Parts/Assemblies Pusher Assembly Parts EP2114, EP2115, EP2116, EP2117 ITEM # DESCRIPTION QTY. PART # Key, 1/2 x 2” D1682 Wheel, foam-filled EC9144 Carrier wheel shaft, 5", 1" OD EH0266 Weights support bracket EP0554 Wheel hub EP0555 Wheel shaft, 2" EP0557 Weights mounting plate EP0558 Motor cover...
  • Page 76 Parts/Assemblies Sump Opener (W65982)
  • Page 77 Parts/Assemblies Parts for Sump Opener (W65982) ITEM # DESCRIPTION QTY. PART # Opener handle E5967 Key, 1/4" x 1-1/2" E9007 Flange bearing, 1", w/collar J0003 Screw, 3/8 -16 x 1” J0606 Screw, 3/8 – 16 x 1-1/2” J0627 Screw, 3/8 – 16 x 2” J0650 Screw, 3/8 - 16 x 3”...
  • Page 78 Parts/Assemblies Flush Floor Center Sump (16” - EP3128, 24” – EP3124) ITEM # DESCRIPTION QTY. 16” 24” Lower conduit EH3003 EH3003 Cross member EP3000 EP3000 Upper conduit EP3001 EP3005 Conduit shield, right side EP3002 EP3007 Conduit shield, left side EP3003 EP3006 Sump EP3028...
  • Page 79 Parts/Assemblies Full Floor Center Sump (EP0565), 16” & 21” Conveyor ITEM # DESCRIPTION QTY. PART # Frame EP0566 Gate EP0567 Bottom support EP0568 Rail EP0569 Pull rod attachment bracket EP0572 Gate side seal EP0573 Roller bearing, 1-1/2”, 3/8” bore J0045 Screw, 3/8 –...
  • Page 80 Parts/Assemblies Intermediate Sump (W65979 – 16”; W65980 – 21”)
  • Page 81 Parts/Assemblies Intermediate Sump (W65979 – 16”; W65980 – 21”) Parts ITEM # DESCRIPTION QTY. 16” PART # 21” PART # Roller bearing, 1-1/2”, 3/8” bore J0045 J0045 Huckbolt, 3/16" J0475 J0475 Carriage bolt, 3/8" x 1" J06064 J06064 Screw, 3/8 – 16 x 1-1/4”, HHWZ J06112 J06112 Screw, 3/8 –...
  • Page 82 Parts/Assemblies Chain & Paddle Assy. (EP0540) ITEM # DESCRIPTION QTY. PART # Chain, 81X EP0541 Paddle support bracket EP0543 Front stiffener EP0544 UHMW paddle EP0545 Screw, 3/8 – 16 x 1-1/4” J0616 Lock nut, 3/8” – 16 J1025 Rubber paddle, 6-1/2 x 9” J97916...
  • Page 83 Parts/Assemblies 108” Backboard Section (EP2100) ITEM # DESCRIPTION QTY. PART # Tube, 2 x 2 x1/4” ,4" long EP0517 Back cover, 108" EP0518 Front cover, 108" EP0519 End brace EP0520 Scraper assy., 107", EP0521 Lift bracket EP0561 Conduit cover, 101" EP0562 Frame, 108"...
  • Page 84 Parts/Assemblies Drive Housing (EP2103)
  • Page 85 Parts/Assemblies Drive Housing (EP2103) Parts ITEM # DESCRIPTION QTY. PART # Pivot weldment EP0500 Center carrier wheel weldment EH0144 Center carrier wheel shim EH0146 Pivot plate stiffener, UHMW EP0507 Pivot plate EP0506 Drive housing stiffener weldment EP0505 Horiz. pivot mounting weldment EP0504 Friction disc EP0503...
  • Page 86 Parts/Assemblies Head Assembly (EP2104) ITEM # DESCRIPTION QTY. PART # Shaft, 2- 3/16” EP0515 Frame EP1104 Bearing, 2-3/16”, 4-bolt J00618 Screw, 5/8 - 11 x 2-1/4” J0792 Nut, 5/8” – 11 J1046 Split lock washer, 5/8” J1218 Sprocket, 81X, 8 teeth, 2-3/16" bore J2135 Key, 1/2 sq.
  • Page 87 Parts/Assemblies Tail Section (EP2102) ITEM # DESCRIPTION QTY. PART # Scraper assy., 22” EP0523 Tail shaft, 1-15/16” EP0559 Agitator EP0560 Tail frame EP1102 Take-up frame J00697 Take-up bearing, 1-15/16” J00698 Screw, 3/8 – 16 x 1” J0611 Carriage bolt, 3/8 – 16 x 1-1/2” J0632 Screw, 5/8 - 11 x 1-1/2”...
  • Page 88 Parts/Assemblies Rear Inner Carrier Wheel Assy. (EP0529) ITEM # DESCRIPTION QTY. PART # Wheel, 6" EH0129 Wheel weldment EH0144 Washer EH0260 Wheel shaft, 1” OD EH0266 Support weldment EP0530 Screw, 3/8 – 16 x 1-1/4” J0616 Screw, 3/8 – 16 x 1-1/2” J0627 Flange lock nut, 3/8”...
  • Page 89 Parts/Assemblies Front Carrier Wheel Assy. (EP0531) ITEM # DESCRIPTION QTY. PART # Wheel, 6" EH0129 Washer EH0260 Wheel shaft, 1” OD EH0266 Support weldment EP0532 Screw, 3/8 – 16 x 1-1/2” J0627 Lock nut, 3/8” – 16 J1025 Rear Carrier Wheel Assy. (EP0534) ITEM # DESCRIPTION QTY.
  • Page 90 Parts/Assemblies Front End Carrier Wheel Assy. (EP0536) ITEM # DESCRIPTION QTY. PART # Wheel, 6" EH0129 Washer EH0260 Wheel shaft, 1” OD EH0266 Wheel support EP0537 Screw, 3/8 – 16 x 1-1/2” J0627 Lock nut, 3/8” – 16 J1025 Rear End Carrier Wheel Assy. (EP0538)* ITEM # DESCRIPTION QTY.
  • Page 91 Parts/Assemblies Pusher Carrier Wheel Assy. (EP0653) ITEM # DESCRIPTION QTY. PART # Wheel, 6" EH0129 Carrier wheel weldment EH0144 Washer EH0260 Wheel shaft, 1” OD EH0266 Support weldment EP0652 Screw, 3/8 – 16 x 1-1/2” J0627 Lock nut, 3/8” – 16 J1025...

  • Page 92: Contact Information

    Contact Information CONTACT INFORMATION Owner’s manuals are available from Sukup and additional copies can be requested at the address, phone number or e-mail address shown below. Please indicate manual number L14359M when requesting 5K Commercial Paddle Sweep Owner’s Installation & Operation Manual.

Table of Contents