Page 1
P/N: 56717-OM ORDOCK INC. Website: Nordockinc.com ~ Email: Sales@Nordockinc.com ~ Toll free: 866-885-4276 Nordock Inc. reserves the right to make changes to specifications without notice or obligation. Nordock products may be covered by various U.S. and foreign patents or pending applications.
Product Identification It is very important that in order to obtain the best possible service from Nordock Inc., please include the model and serial number of the safety gate whenever you contact us. Below is the same serial number decal that will be found on the front of the movable barrier.
1. Replace the product or the defective portion thereof without charge to the purchaser; or, 2. Alter or repair the product on site or elsewhere, as Nordock Inc. may deem advisable, without charge to the purchaser. The warranty stated herein is that offered by Nordock Inc. and expressly disclaims all implied warranties including those of merchantability and fitness.
7. Whenever any maintenance or repair is to be performed on the safety gate, Barricade the area around the barrier and place clear signage on the perimeter that the unit is not to be operated. 8. If you have any questions, contact your supervisor or your local Nordock Incorporated representative. - 4 -...
Nordock Inc. Parts and Service Manual 56717-OM, ASG1010 Powered Safety Gate Installation General Notes The gate may be assembled and installed in one of two ways: 1. Assemble all stationary gate components together flat on the floor and tilt up to the vertical position.
Page 7
Nordock Inc. Parts and Service Manual 56717-OM, ASG1010 Powered Safety Gate NOTE: Barrier and Cables are not shown in drawing above. To ensure correct operation of the safety gate, it is critical that the two vertical side columns (1 & 2) are installed plumb and parallel to one another in both vertical planes.
Nordock Inc. Parts and Service Manual 56717-OM, ASG1010 Powered Safety Gate Assembly Instructions NOTE For ease of installation, the spreader channel assembly has all components except the cables shipped factory assembled. Refer to the installation parts diagram and table starting on page 5 as needed.
Page 9
Nordock Inc. Parts and Service Manual 56717-OM, ASG1010 Powered Safety Gate 5. Bolt the spreader channel/torque shaft assembly to the top of the upright columns, using the eight 3/8” x 1-1/2” long bolts (22) and fasteners (23, 24 & 25) provided. Each connection should have a 3/8”...
Nordock Inc. Parts and Service Manual 56717-OM, ASG1010 Powered Safety Gate Column Mounting Instructions If the gate was partially assembled flat on the ground, it must now be tilted to the vertical upright position. NOTE Columns (1&2) are shipped with the roller (3 to 5) for the counterweight cable factory assembled.
Page 11
Nordock Inc. Parts and Service Manual 56717-OM, ASG1010 Powered Safety Gate BARRIER CABLE QUICK LINK CONNECTOR EYEBOLT, FACTORY BARRIER INSTALLED CABLE LEFT SIDE RIGHT SIDE SHOWN SHOWN 3. Using a forklift or other suitable lifting device, lift the gate up between the columns.
Nordock Inc. Parts and Service Manual 56717-OM, ASG1010 Powered Safety Gate Counterweight Installation Instructions 1. 1/2” support rods are still holding barrier in raised position. 2. Place a temporary spacer block, by others, (approx. 2” high) in bottom pocket of each beam.
Page 13
Nordock Inc. Parts and Service Manual 56717-OM, ASG1010 Powered Safety Gate NOTES • The number of cable wraps on the drum will vary with gate height and width. • After temporary blocks are removed, the counterweight should not bottom out before barrier is to the top of its travel.
Test gate function by operating gate up and down. The gate should stop automatically at the upper travel limit. The gate has been tested at Nordock. However, the bottom limit may need recalibration for any drum/cable changes. See setup procedure below.
Nordock Inc. Parts and Service Manual 56717-OM, ASG1010 Powered Safety Gate Operation WARNING Before operating or maintaining the safety gate, read and follow the safety practices contained in this manual. Failure to follow the guidelines in this manual and those in effect in the workplace can result in serious bodily harm and equipment damage.
Nordock Inc. Parts and Service Manual 56717-OM, ASG1010 Powered Safety Gate Maintenance and Lubrication WARNING Before operating or maintaining the safety gate, read and follow the safety practices contained in this manual. Failure to follow the guidelines in this manual and those in effect in the workplace can result in serious bodily harm and equipment damage.
Nordock Inc. Parts and Service Manual 56717-OM, ASG1010 Powered Safety Gate Parts List Item Qty. Description / Model Note UPRIGHT COLUMN, LEFT, Special 10’ HIGH 52-0510 UPRIGHT COLUMN, RIGHT, Special 10’ HIGH 520513 BARRIER ASSEMBLY 10’ WIDE 52-0519 SPREADER CHANNEL, SPECIAL 10’...
Page 18
Nordock Inc. Parts and Service Manual 56717-OM, ASG1010 Powered Safety Gate Item Qty. Description / Model Note BUSHING, OILITE, 1/2”ID x 5/8”OD x 1”LG. 13-0434 SHOCK ABSORBER 13-0743 (c/w 9) PIN ASSEMBLY, COUNTERWEIGHT PULLEY 52-0526 SHAFT PIVOT BRACKET, LEFT 13-0892-L...