Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for ekwb EK-PRO GPU WB H100 Rack - Nickel + Inox
Summary of Contents for ekwb EK-PRO GPU WB H100 Rack - Nickel + Inox
- Page 1 EK-PRO GPU WB H100 Rack - Nickel + Inox GPU WATER BLOCK USER GUIDE...
- Page 2 Before you start using this product, please follow these basic guidelines: Carefully read the manual before beginning with the installation process. Remove your graphics card from the computer for the safest mounting process to prevent any possible damage to your GPU or its circuit board (PCB).
-
Page 3: Table Of Contents
TABLE OF CONTENTS BOX CONTENTS WATER BLOCK DIMENSIONS TECHNICAL SPECIFICATIONS AND WATER BLOCK PARTS PREPARING YOUR GRAPHICS CARD REMOVING THE STOCK COOLER CLEANING THE PCB CUTTING AND PLACING THERMAL PADS APPLYING THERMAL COMPOUND INSTALLING THE WATER BLOCK PLACING THE BLOCK ON THE GRAPHICS CARD CHECKING THE CONTACT IN CASE OF HIGH TEMPERATURES ATTACHING THE WATER BLOCK INSERTING THE GRAPHICS CARD INTO THE CHASSIS... -
Page 4: Box Contents
H100 Rack Backplate (1x) 107035 9049 Screw M2.5x10 ax1 - Black (3x) 104344 Screw size guide (1x) 103012 EK-Pro GPU WB H100 Rack - Nickel + Inox (1x) 3831109908792 Washer POLYAMID M2.5 0.7mm Washer POLYAMID M2.5 0.5mm PASTE Thermal Grizzly Hydronaut (10x) 8623... -
Page 5: Water Block Dimensions
WATER BLOCK DIMENSIONS 255.7 mm 244.3 mm 21.7 mm 242.4 mm 17.8 mm - 5 -... -
Page 6: Technical Specifications And Water Block Parts
TECHNICAL SPECIFICATIONS AND WATER BLOCK PARTS Position Description Quantity 107032 099 - Baker - H100 Rack Coldplate (Ni) 107041 099 - Kovina - H100 Rack Insert 107036 099 - Kovina - H100 Rack Pro Top 107037 099 - Alu - H100 Rack Power Adapter 107064 099 - OR - H100 Rack 103767... -
Page 7: Preparing Your Graphics Card
Do not forget to unplug all the LED and fan connectors. Pay attention to the following steps in order to install the EK-Pro GPU WB H100 Rack - Nickel + Inox water block onto the graphics card. -
Page 8: Cutting And Placing Thermal Pads
CUTTING AND PLACING THERMAL PADS STEP 1 Your GPU water block comes with un-cuted thermal pads to cover Thermal Pad F 1.0 mm all the VRM components, such as COILs, MOSFETs, and drivers. Please use 1.0 mm thick thermal pads which should be placed on the water block, as illustrated below. -
Page 9: Applying Thermal Compound
APPLYING THERMAL COMPOUND Apply the enclosed EK-TIM Ectotherm thermal grease (thermal compound) on the GPU heat spreader – IHS – as shown in the image. The layer of the thermal compound must be thin and even over the entire surface of the IHS. The excessive or uneven application of thermal grease may lead to poor performance! For this Step, you will need:... - Page 10 STEP 3 Use stock cross backplate from the original card and mount it with original stock M3 screws. STEP 3 STEP 4 Secure power cable with mounting it into included inox power adapter. STEP 4b Insert 8-pin power connector in to the inox adapter. Pads on the power adapter must be alligned with openings in inox power adapter.
-
Page 11: Checking The Contact In Case Of High Temperatures
Then repeat Steps from the previous section to re-attach the block. In case you fail to obtain good contact, please check again or contact our support service at https://www.ekwb.com/customer-support/. - 11 -... -
Page 12: Inserting The Graphics Card Into The Chassis
INSERTING THE GRAPHICS CARD INTO THE CHASSIS Carefully lift your graphics card with the installed water block and insert it into your PC’s motherboard PCI express expansion slot. Please keep in mind that your graphics card is heavier than before it was equipped with the water block. -
Page 13: Support And Service
SUPPORT AND SERVICE In case you need assistance or wish to order spare parts or a new mounting mechanism, please contact: https://www.ekwb.com/customer-support/ For spare parts orders, refer to the page with “TECHNICAL SPECIFICATIONS AND WATER BLOCK PARTS” where you can find the EAN number of each part you might need.
Need help?
Do you have a question about the EK-PRO GPU WB H100 Rack - Nickel + Inox and is the answer not in the manual?
Questions and answers