Related Manuals for Geniatech RZ-G2L-OSM
Summary of Contents for Geniatech RZ-G2L-OSM
- Page 1 RZ-G2L-OSM yocto User's Manual Room 02-04, 10/F, Block A, Building 8, Shenzhen International Innovation Valley, Dashi Road, Nanshan District, Shenzhen, Guangdong, China Emai: support@geniatech.com Tel: (+ 86) 755 86028588...
- Page 2 REVISION HISTORY Date Version number Reason for change Modifiers Remarks 2022-11-03 Create Document Room 02-04, 10/F, Block A, Building 8, Shenzhen International Innovation Valley, Dashi Road, Nanshan District, Shenzhen, Guangdong, China Emai: support@geniatech.com Tel: (+ 86) 755 86028588...
-
Page 3: Table Of Contents
3.2 WIFI Connection ..............................6 3.3 Ethernet ...................................11 3.4 TF card ..................................11 3.5 MIPI Screen & Touch .............................13 Room 02-04, 10/F, Block A, Building 8, Shenzhen International Innovation Valley, Dashi Road, Nanshan District, Shenzhen, Guangdong, China Emai: support@geniatech.com Tel: (+ 86) 755 86028588... -
Page 4: Rzg2L-Osm Operating System
Installation steps are described in the <RZG2L-OSM_yocto> burn-in instructions document>. 3. Function Description 3.1 Hardware interface schematic Room 02-04, 10/F, Block A, Building 8, Shenzhen International Innovation Valley, Dashi Road, Nanshan District, Shenzhen, Guangdong, China Emai: support@geniatech.com Tel: (+ 86) 755 86028588... - Page 5 （1） Serial cable*1, connect to the serial port (J11), open the serial debugging software to select COM port and baud rate 115200 Pin NO Definition UART_RX2 UART_TX2 Room 02-04, 10/F, Block A, Building 8, Shenzhen International Innovation Valley, Dashi Road, Nanshan District, Shenzhen, Guangdong, China Emai: support@geniatech.com Tel: (+ 86) 755 86028588...
-
Page 6: Wifi Connection
3.2 WIFI Connection 3.2.1 Test preparation: two WiFi antennas, connected as shown Room 02-04, 10/F, Block A, Building 8, Shenzhen International Innovation Valley, Dashi Road, Nanshan District, Shenzhen, Guangdong, China Emai: support@geniatech.com Tel: (+ 86) 755 86028588... - Page 7 Turn on the WiFi node, and then enter ifconfig to see if the node is on Room 02-04, 10/F, Block A, Building 8, Shenzhen International Innovation Valley, Dashi Road, Nanshan District, Shenzhen, Guangdong, China Emai: support@geniatech.com Tel: (+ 86) 755 86028588...
- Page 8 IP, if it has IP, it is successfully connected. Room 02-04, 10/F, Block A, Building 8, Shenzhen International Innovation Valley, Dashi Road, Nanshan District, Shenzhen, Guangdong, China Emai: support@geniatech.com Tel: (+ 86) 755 86028588...
- Page 9 (the name of the encrypted WiFi in the environment) key_mgmt=WPA-PSK psk="12345678" (WiFi password) Room 02-04, 10/F, Block A, Building 8, Shenzhen International Innovation Valley, Dashi Road, Nanshan District, Shenzhen, Guangdong, China Emai: support@geniatech.com Tel: (+ 86) 755 86028588...
- Page 10 IP, and if it has an IP, it is successfully connected Room 02-04, 10/F, Block A, Building 8, Shenzhen International Innovation Valley, Dashi Road, Nanshan District, Shenzhen, Guangdong, China Emai: support@geniatech.com Tel: (+ 86) 755 86028588...
-
Page 11: Ethernet
（1） Insert the TF card into the (hot-swappable) card slot fdisk -l View partition （2） Room 02-04, 10/F, Block A, Building 8, Shenzhen International Innovation Valley, Dashi Road, Nanshan District, Shenzhen, Guangdong, China Emai: support@geniatech.com Tel: (+ 86) 755 86028588... - Page 12 /dev/mmcblklpl /media Manual mount （3） df -h View （4） Room 02-04, 10/F, Block A, Building 8, Shenzhen International Innovation Valley, Dashi Road, Nanshan District, Shenzhen, Guangdong, China Emai: support@geniatech.com Tel: (+ 86) 755 86028588...
-
Page 13: Mipi Screen & Touch
（1） Connect the MIPI screen as shown in the diagram （2） Power on and start, observe whether there is backlight Room 02-04, 10/F, Block A, Building 8, Shenzhen International Innovation Valley, Dashi Road, Nanshan District, Shenzhen, Guangdong, China Emai: support@geniatech.com Tel: (+ 86) 755 86028588... - Page 14 （3） The boot screen is as follows Room 02-04, 10/F, Block A, Building 8, Shenzhen International Innovation Valley, Dashi Road, Nanshan District, Shenzhen, Guangdong, China Emai: support@geniatech.com Tel: (+ 86) 755 86028588...
- Page 15 （5） TP Test: Click on the software with your finger touch screen, for example, the terminal software Room 02-04, 10/F, Block A, Building 8, Shenzhen International Innovation Valley, Dashi Road, Nanshan District, Shenzhen, Guangdong, China Emai: support@geniatech.com Tel: (+ 86) 755 86028588...
- Page 16 Room 02-04, 10/F, Block A, Building 8, Shenzhen International Innovation Valley, Dashi Road, Nanshan District, Shenzhen, Guangdong, China Emai: support@geniatech.com Tel: (+ 86) 755 86028588...
- Page 17 VCC1_LED+ DSI_DATA3_N VCC1_LED+ I2C TOUCH Connector (J36) Pin NO Definition I2C_A0_SCL I2C_A0_SDA VDD_3V3 TP_nRST_C TP_nINT_C Room 02-04, 10/F, Block A, Building 8, Shenzhen International Innovation Valley, Dashi Road, Nanshan District, Shenzhen, Guangdong, China Emai: support@geniatech.com Tel: (+ 86) 755 86028588...
Need help?
Do you have a question about the RZ-G2L-OSM and is the answer not in the manual?
Questions and answers