Subscribe to Our Youtube Channel
Related Manuals for Geniatech RS-G2L100
Summary of Contents for Geniatech RS-G2L100
- Page 1 Spec V1.0 RS-G2L100 User Guide Contact us for more details: https://www.geniatech.com/...
-
Page 2: Table Of Contents
Spec V1.0 Content 1. Yocto on the RS-G2L100.................. 3 2. Installing Yocto....................3 2.1 Hardware tools required:................3 2.2 Software tools required:................3 2.3 Step 1. Download the Yocto images and Tools from the website.... 3 2.4 Step 2. Bring the board into burn mode.............4 2.5 Step 3. -
Page 3: Yocto On The Rs-G2L100
Spec V1.0 1. Yocto on the RS-G2L100 RS-G2L100 currently supports the system：Yocto. 2. Installing Yocto 2.1 Hardware tools required: USB to TTL HOST PC The RS-G2L100 Board 12V power supply 2.2 Software tools required: Tera Term 2.3 Step 1. Download the Yocto images and Tools from the website 1) Download the Yocto images from below website: https://mega.nz/file/CMwCkRoK#Ylf3IwSvw3KNjDOKR7en-... -
Page 4: Step 2. Bring The Board Into Burn Mode
2) USB to TTL :USB port is connected to the computer, and one end can be connected to the board through a DuPont cable, the serial port interface of the board is defined as follows: Contact us for more details: https://www.geniatech.com/... -
Page 5: Step 3. Flash The Yocto Image
Spec V1.0 2.5 Step 3. Flash the Yocto image 1) Connect the RS-G2L100 to the computer via USB to TTL.Open Tera Term, select Serial -> port: select the Port recognized by the computer to the USB to TTL; 2) Unzip the Yocto images file.Set baud rate: Tera Term ->Setup->Serial port... - Page 6 Spec V1.0 3) When everything is ready, plug in the device. Tera Term will display the message: 4) Send the Flash_Writer_SCIF_RZG2L_SMARC_PMIC_DDR4_2GB.mot file to the system. Contact us for more details: https://www.geniatech.com/...
- Page 7 ! ('.' & CR stop load) 6) Send the bl2_bp-smarc-rzg2l_pmic.srec file to the system. ”SPI Data Clear(H'FF) Check : H'00000000-0000FFFF,Clear OK?(y/n)” When you see the following prompt, please enter and continue to execute. Contact us for more details: https://www.geniatech.com/...
- Page 8 ! ('.' & CR stop load) 8) Send the fip-smarc-rzg2l_pmic.srec file to the system.Wait for the file upload to finish and the device is powered off. 9) Put the board into boot mode: 1-off 2-off 3-on 4-off..Put the core-image- Contact us for more details: https://www.geniatech.com/...
- Page 9 10) RS-G2L100 to the computer via USB to TTL.Open Tera Term,after connecting to the power supply, keep pressing Enter on the keyboard to make the device enter uboot mode. 11) RS-G2L100 access network and set IP under uboot mode.(Please use this network port : J8) setenv ipaddr 10.168.4.104 setenv ethaddr 88:33:14:f6:c0:d4 setenv serverip 10.168.4.204...
-
Page 10: Step 4. Reboot And Enjoy
512 and then converted to hexadecimal. For example, the file size in the figure: 640665600 bytes /512=1251300 is converted to hexadecimal 1317e4. 2.6 step 4. Reboot and enjoy ! After completing the programming, power off and restart the device.(login:root) Contact us for more details: https://www.geniatech.com/... -
Page 11: G2L00 Yocto Introduction
This release note describes the contents, building procedures and important points of the G2L Board Support Package (hereinafter referred to as “BSP”) The recommended environment for BSP is shown below. The equipment and software used in this environment are listed in the following table. Contact us for more details: https://www.geniatech.com/... -
Page 12: Building Instructions Of A Bsp
Notes - (1) and apply the patches before the step (4) in the section 3.2.1. 2) Setup a build environment Run the commands below. The environment to build is set by the source command. Contact us for more details: https://www.geniatech.com/... - Page 13 $ cd ~/user_work/build $ bitbake core-image-minimal -c populate_sdk The resulting SDK installer will be located in build/tmp/deploy/sdk/ The SDK installer will have the extension .sh To run the installer, you would execute the following command: Contact us for more details: https://www.geniatech.com/...
- Page 14 (4) in the section 3.2.1. When you want to know the details of the LSI version, please contact Renesas. $ cd ~/user_work/meta-rzg2 $ patch -p1 < ../extra/0001-linux-renesas-add-workaround-patch-for-gicv3.patch $ patch -p1 < ../extra/0002-tf-a-add-rd-wr-64-bit-reg-workaround.patch Contact us for more details: https://www.geniatech.com/...
Need help?
Do you have a question about the RS-G2L100 and is the answer not in the manual?
Questions and answers