Page 1
MODE D'EMPLOI MANUAL DE INSTRUCCIONES POOL WATCH SWIMMING POOL ALARM MODEL NUMBER AC 50032 NSF - 50 ASTM F2208 Thank you for choosing Blue Torrent. PLEASE READ BEFORE RETURNING THIS PRODUCT FOR ANY REASON. SAVE THIS MANUAL FOR FUTURE REFERENCE.
SAFETY GUIDELINES — DEFINITIONS It is important for you to read and understand this manual. The information it contains relates to protecting YOUR SAFETY and PREVENTING PROBLEMS. The symbols below are used to help you recognize this information. DANGER: Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury.
Page 3
WARNING: • Do not leave toys or objects floating in an unattended pool. The AC 50032 is a pool alarm Toys or objects could be seen designed to detect intrusions as an invitation for a child to into an unsupervised pool.
Page 4
POOL WATCH AC 50032 POOL CONTENTS: ALARM FACTS A. Main Alarm Body B. Remote Siren • This is a alarm designed to C. AC Adapter for Remote detect an intrusion into the Siren swimming pool, especially by D. Mounting Screws for young children.
1 for pools up to 17'. For larger pools, a second alarm will be needed at location 2. For a Round Pool: the AC 50032 should be installed in any of the 4 locations for pools up to 24'. For larger pools, a second alarm...
Page 6
INSTALLING THE ALARM STEP 1 Test fit alarm in location determined above. As shown in Figure 1, the alarm sensor pipe throat should be in the water and the mounting area level and flat. The alarm base should easily snap into the bottom of the main alarm body and allow the sensor throat to extend directly into the pool at a 90°...
Page 7
STEP 3 Drill holes into hole markings with a 1/4" masonry drill. Refer to Figure 2 to drill holes 1.75" deep. To achieve the right depth, measure 1.75" inches from the end of the drill bit, and mark point with masking tape. Stop drilling when deck is level with tape.
Page 8
STEP 6 Adjust and maintain pool water level. This step is imperative in order for the pool alarm sensor to perform properly. The alarm sensor throat should be no more shallow or deep than 0.19" to 0.39" in the water at all times. Never block or fill air hole located on the back of alarm sensor throat.
Page 9
MOUNTING THE REMOTE SIREN Remove the Phillips head screw from the back of the remote siren. Install 1 long life alkaline 9V battery and replace cover. Plug the AC adapter into the remote siren. Then place remote siren on flat surface or use a screw to mount it to wall near electrical socket.
Page 10
Contact the manufacturer with any additional questions. UNDERSTANDING "FAR" MODE To help reduce false alarms, the Pool Watch AC 50032 Alarm is equipped with "False Alarm Resistant" technology. When in FAR mode, the alarm monitors the water and detects outside interference from conditions such as wind and automatic cleaners.
Page 11
TESTING THE AC 50032 POOL ALARM The unit MUST be tested on a weekly basis. To test the alarm, create a simple device (see Figure 8 and Figure 9) that will stimulate the size and weight of a young child using the...
Page 12
USING THE AC 50032 POOL ALARM SWIM MODE: The unit must be set to "SWIM" mode before swimmers enter the pool in order for the pool to be used without the alarm sounding. Once the switch at the front of the alarm head is moved to SWIM/ ON, the alarm will emit a long beep.
TROUBLESHOOTING GUIDE Changes or modifications not expressly approved by party responsible for compliance could void the user's authority to operate equipment. ALARM INDICATOR GUIDE 1. Batteries ON: Two beeps and the GREEN LED flashes every 21 seconds. 2. From ON to OFF: The RED LED will flash every 20 seconds.
This product is not intended for attempted by anyone other than commercial use, and accordingly, Blue Torrent and its Authorized such commercial use of this Service Centers. product will void this warranty. All other guarantees, express or A defective product meeting the implied, are hereby disclaimed.
Need help?
Do you have a question about the AC 50032 and is the answer not in the manual?
Questions and answers