Hakko Electronics 373 Instruction Manual
Self feeder
Hide thumbs
Also See for 373:
- Instruction manual (15 pages) ,
- Quick start manual (8 pages) ,
- Manual (10 pages)
Table of Contents
Advertisement
Quick Links
Instruction Manual
Thank you for purchasing the HAKKO 373 Self Feeder.
Please read this manual carefully before operating the HAKKO 373.
Store the manual in a safe, easily accessible place for future reference.
PRECAUTIONS ...................................................... 1
SPECIFICATIONS ................................................... 1
PART NAMES ......................................................... 2
ASSEMBLY ............................................................. 3
OPERATION ........................................................... 6
TROUBLESHOOTING ............................................ 9
REPLACEMENT PARTS ....................................... 10
OPTIONS & REPLACEMENT PARTS .................. 11
PARTS LIST .......................................................... 13
SELF FEEDER
●
●
TABLE OF CONTENTS
Advertisement
Table of Contents
Related Manuals for Hakko Electronics 373
Summary of Contents for Hakko Electronics 373
-
Page 1: Table Of Contents
SELF FEEDER Instruction Manual ● Thank you for purchasing the HAKKO 373 Self Feeder. Please read this manual carefully before operating the HAKKO 373. Store the manual in a safe, easily accessible place for future reference. ● TABLE OF CONTENTS PRECAUTIONS ............ -
Page 2: Precautions
PRECAUTIONS CAUTION ● Setting up should be done while the soldering iron is cool, or you may get burnt. ● Do not force the guide pipe bend or turn as this may result in damage. ● Do not operate with tube bending or holding in sharp angle. It may cause to clogging. ●... -
Page 3: Part Names
PART NAMES ① Jack for Switch ② Feed Speed Control Knob ③ Feed Time Control Knob ④ Mode Switch ⑤ Power Switch ⑥ Release Lever ⑦ Securing Screw ⑧ Tension Adjustment Knob ① ② ③ ④ ⑤ ⑨ Tension Gear Guide Shaft ⑩... -
Page 4: Assembly
ASSEMBLY Make sure the selected guide pipe assembly or tube unit matches the soldering iron and solder diameter to be used. (a) Attach the Tube to Guide Pipe Assembly. CAUTION The tube is double structure. Insert the inside tube into the joint and pass the outer tube over the ... - Page 5 4-1. Install the Solder Dia. 1. Remove the tension gear guide shaft. Adjustment Ring 2. Attach the solder dia. adjustment Solder Dia. ring according to the diameter of Tension Gear Guide Shaft Adjustment Ring your desired solder and attach the tension gear guide shaft.
- Page 6 Remove the tension gear guide shaft turning with a spanner or pliers. (c) Replace the guide pipe assembly if it is necessary. 4-6. Vertical Mounting The HAKKO 373 can be mounted vertically. Mount as shown in the figure. 46mm 2-φ4.2...
-
Page 7: Operation
OPERATION Solder will be fed by pressing the feed switch (or foot switch). ■ MODE □ AUTO MODE If you press the feed switch, solder will be fed with set time and speed independently of length of pressing time. □ MANUAL MODE Solder will be fed with set speed during pressing the feed switch. - Page 8 OPERATION ■ Adjustment for the After feed solder, the specified length of solder can be returned. Soldering robots Amount of Solder may need this solder return function. Return Amount of solder return is adjustable within 0~5 mm (0~0.2 in.). Solder should be taken up if the amount of solder return is bigger than the amount of solder feed.
- Page 9 ■ Usage of Iron stand Top-feed type Bottom-feed type FX-1001 FX-8801, FX-8805 These can be used as they are. Others Exchange with the optional retaining clip. (Refer to Refer to the instruction manual included with the “6. OPTIONS & REPLACEMENT PARTS/Replace- bottom-feed type iron receptacle for attachment ment parts &...
-
Page 10: Troubleshooting
TROUBLESHOOTING If the solder can not be fed smoothly, please check following points. ■ Are you using proper parts according to the diameter of solder? ■ Did you adjust the tension properly? ■ Is the tube bent or transformed? ■ Is solder adhered at the feed gear or the tension gear? ■... -
Page 11: Replacement Parts
REPLACEMENT OF PARTS 1. When you change the Please replace the parts indicated on the Solder Diameter following chart when you change solder diameter. Solder Dia. Guide Tube Nozzle Changing matter Adjustment Ring Pipe Unit From the range of 0.6~1.0mm to the range of 0.6~1.0mm replace replace same... -
Page 12: Options & Replacement Parts
OPTIONS & REPLACEMENT PARTS Setup options (Top-feed type) Applicable soldering iron Dia. of Solder (ø) Solder Dia. Adjustment Ring Guide Pipe Asse’y Tube Unit 0.6 mm, 0.65 mm B1626 B3726 FM-2030 0.8 mm B1627 B3727 B3477 FN-1101 1.0 mm B1628 B3728 FX-9701 1.2 mm... - Page 13 Replacement parts & options (Top-feed type) Part No. Part Name Dia. of Solder Note B1699 Nozzle 0.6 mm B1700 Nozzle 0.8 mm B1701 Nozzle 1.0 mm B1702 Nozzle 1.2 mm B1703 Nozzle 1.6 mm B1704 Guide Pipe A 0.6 ~ 1.0 mm FX-8801 B1705 Guide Pipe B...
-
Page 14: Parts List
PARTS LIST Item No. Part No. Part Name Description B1897 Cover for Feeding Unit B1882 Tension Gear Guide Shaft B1626 Solder Dia. Adjustment Ring for 0.6, 0.65mm B1627 Solder Dia. Adjustment Ring for 0.8mm B1628 Solder Dia. Adjustment Ring for 1.0mm B1629 Solder Dia. - Page 15 Note: Spare or repair parts do not include mounting screws, if they are not listed on the description. Screws must be ordered separately. Pan Head Screw M 3 x 4(8) Pan Head Screw with Washer M 3 x 5(4) Pan Head Screw with Washer (w/Spring, Plain Washer) M 3 x 6(2) Pan Head Screw...
- Page 16 HEAD OFFICE 4-5, Shiokusa 2-chome, Naniwa-ku, Osaka 556-0024 JAPAN TEL: +81-6-6561-3225 FAX: +81-6-6561-8466 https://www.hakko.com E-mail: sales@hakko.com OVERSEAS AFFILIATES U.S.A.: AMERICAN HAKKO PRODUCTS, INC. TEL: (661) 294-0090 FAX: (661) 294-0096 Toll Free (800) 88-HAKKO 4 2 5 5 6 https: //www.HakkoUSA.com E-mail: Support@HakkoUSA.com HONG KONG: HAKKO DEVELOPMENT CO., LTD.