Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for DKN CT PRO
Summary of Contents for DKN CT PRO
- Page 1 CT PRO OWNER’S MANUAL WEBSITE MANUAL...
- Page 2 CURVED TREADMILL...
- Page 3 WARNING Read all instruction carefully before use this product. Retain this owner’s manual for the future’s reference: ----When you are running, keep your hand swinging natural, stare frontward, never look down at your feet. ----Add the speed step by step when running. ----Leave the treadmill after the running belt stop stably.
- Page 4 IMPORTANT SAFETY PRECAUSTION 1. Plug the power cord of the treadmill directly into a dedicated grounded circuit. This product must be grounded. If it has breakdown, grounding provides a path of least resistance for electric current to reduce the risk of electric shock. 2.
- Page 5 The owner’s manual is only for customers’ reference. ► The supplier cannot guarantee for mistakes occurring due to translation or change in technical specification of the product. ► DKN-Technology ASSUMES NO RESPONSIBILITY FOR PERSONAL INJURY OR PROPERTY DAMAGE SUSTAINED BY OR THROUGH THE USE OF THIS PRODUCT...
-
Page 6: Assembly Steps
ASSEMBLY STEPS ASSEMBLY STEP ONE: 1. Take the main frame(10) from the wooden pallet, then put the main frame(10) on the ground, as the picture shown. ASSEMBLY STEP TWO 1. Insert the limited board A which are on the upright tubes (12 L/R) into the hole B in the main frame (10),then lock the upright tube (12L/R) in the main frame (10) with Cross pan... - Page 7 ASSEMBLY STEP THREE 1. Connect the extention2 (35) and extension wire3 (36). 2. Insert the Front handrail(14) into the computer frame(13L/R), tightened with Cross pan head screw (22), spring washer(30), and flat washer(31). 3. Lock the Front decor cover (15L/R) tightly in the handrail(13L/R) with Cross screw(39).
- Page 8 ASSEMBLY STEP FOUR 1.Connect the sensor extention1 (34) and sensor extension wire2(35), then follow the P2 instruction, connect the tension extension wire (37) and the tension wire (38); 2. lock the computer frame(13L/R) tightly on the upright tube (12L/R) with Cross pan head screw (22) and Inner serrated washer (23).
- Page 9 ASSEMBLY STEP FIVE 1. Cocking the Left support cover-outside (16) and Left support cover-inside (17) on the left upright tube (12L), tighten with cross pan head screw (28); 2. Cocking the right support cover-outside (18) and right support cover-inside (19) on the right upright tube (12R), tighten with cross pan head screw (28);...
- Page 10 ASSEMBLY STEP SEVEN 1. Insert the silencer foam left 1 (40)and silencer foam left 2 (41) in the main frame (10) separately, like the P3 shown. 2. Insert the silencer foam right (42) in the main frame (10) like the P4 shown. 3.
- Page 11 ASSEMBLY STEP EIGHT 1. fasten the left edging fix (7L) on the left Front edging fix (8L) and left rear edging fix (9L) with Cross tapping screw (26); 2. fasten the right edging fix (7R) on the right Front edging fix (8R) and right rear edging fix (9R) with Cross tapping screw (26);...
-
Page 12: Technical Parameter
ASSEMBLY STEP TEN 1. Follow the P6 instruction, insert the left front base cover (3L) into the left front side cover (1L), then fasten the left front base cover (3L) on the main frame (10) with Hex socket screw (24) 2. -
Page 13: Key Function
MONITOR INSTRUCTION MANUAL KEY FUNCTION ● This key lets you to select and lock on to a particular function you want. SCAN→TIME→CALORIES(CAL) →SPEED→DIST→TOTAL DIST(ODO) ● Pressing and hold with 3 seconds to reset the value to zero (without ODO). SLEEP MODE ●... -
Page 14: Exploded Drawing
EXPLODED DRAWING... -
Page 17: Parts List
PARTS LIST Description Description 1 L/R Front side cover Cross pan head screw M10*20 2L/R Rear side cover Inner serrated washer Φ10 3L/R Front base cover Hex socket screw M6*15 4L/R Rear base cover Cross screw M5*15 5L/R Front edging Cross tapping screw ST5*16 6L/R Rear edging... -
Page 18: Bluetooth Function
BLUETOOTH FUNCTION Check the DKN-Technology website for more information about which apps the Treadmill is compatible with. Turn on Bluetooth function on your tablet or smartphone to connect it with the machine (pairing is not required). Download the app, open it on your device and follow the steps to set it up. -
Page 19: Warranty
WARRANTY DKN-Technology warrants this product to be free from defects in material at the time of the product’s tender of delivery. This ‘Carry-in’ Limited Warranty applies for a period of two (2) years, beginning on the date mentioned on your product invoice or proof of purchase of product issue by DKN-Technology. - Page 20 WEBSITE Make an Appointment to Visit our Showroom...
Need help?
Do you have a question about the CT PRO and is the answer not in the manual?
Questions and answers