Table of Contents
Advertisement
OPTIONS AND FUNCTIONS
OPTIONS can be selected directly by pressing the corresponding button (see CONTROL PANEL).
If an option is not compatible with the selected program see PROGRAMS TABLE, the corresponding LED flashes rapidly 3 times
and beeps will sound. The option will not be enabled.
MULTIZONE
If there are not many dishes to be washed, a half loading may
be used in order to save water, electricity and detergent.
Select the program and then press the MULTIZONE button:
the symbol of the chosen rack will appear on the display. By
default the appliance washes dishes in all racks.
To wash only the specific rack, press this button repeatedly:
shown on the display (only lower rack)
shown on the display (only upper rack)
shown on the display (option is OFF and the appliance will
wash dishes in all racks).
Remember to load the upper or lower rack only, and to
reduce the amount of detergent accordingly.
If upper rack is removed, please apply detergent directly
to tub instead of detergent dispenser.
DELAY
The start time of the program may be delayed for a period of
time between 1 and 12 hours.
1. Press the DELAY button: the corresponding «h» symbol
appears on the display; each time you press the button,
the time (1h, 2h, etc. up to max. 12h) from the start of the
selected wash cycle will be increased.
2. Select the wash program, press the START/PAUSE button
and within 4 seconds close the door: the timer will begin
counting down.
3. Once this time has elapsed, the indicator light «h» switches
off and the wash cycle begins.
To adjust the delay time and select a shorter period of
time, press the DELAY button. To cancel it, press the button
repeatedly until the selected delayed start indicator light «h»
switches off.
The DELAY function cannot be set once a wash cycle has
been started.
TURBO
This option can be used to reduce the duration of the main
programs while maintaining the same washing and drying
performance levels.
After selecting the program, press the TURBO button and the
indicator light will switch on. To deselect the option, press the
same button again.
POWER CLEAN®
Thanks to the additional power jets this option provides
a more intensive and powerful wash in the lower rack, in the
specific area. This option is recommended for washing pots
and casseroles. Press this button to activate POWER CLEAN
(the indicator lights up).
4
TABLET (Tab)
This setting allows you to optimize the performance of the
program according to the type of detergent used.
Press the START/PAUSE button for 3 seconds (the correspon-
ding symbol will light up) if you use combined detergents in
tablet form (rinse aid, salt and detergent in 1 dose).
If you use powder or liquid detergent, this option should
be off.
OPERATION INDICATOR
A LED light projected on the floor indicates that the dishwasher is
working. One of the following operating modes can be selected:
a) Disabled function.
b) When the cycle starts the light goes on for few seconds,
stays off during the cycle and flashes at the end of the cycle.
c) The light stays on during the cycle and flashes at the end of
the cycle (default mode).
If the delayed start was set, the light goes on either for the first
few seconds or the entire duration of the countdown, based
on whether mode b) or c) was set.
The light goes off every time the door is opened. To select the
mode you prefer, switch on the machine, hold down button
P until one of the three letters appears on the display, press
button P until you reach the desired letter (or mode), hold
down button P to confirm the selection.
Note: If NaturalDry is active and it opens the door, then
Operation Indicator will not flash at the end of cycle.
NaturalDry
NaturalDry is a convection drying system which automatically opens
the door during/after drying phase to ensure exceptional drying per-
formance every day. Door opens at the temperature that is safe to your
kitchen furniture, thus door will not be opened when the option of
TURBO is on.
As additional steam protection, special designed protection foil is added
together with the dishwasher. To see how to mount protection foil
please refer to (INSTALLATION GUIDE).
NaturalDry functionality could be disabled by the user as follows:
1. Go to the Dishwasher software menu pressing and holding P
button (6 sec).
2. You are currently in Light Control Menu (please refer to OPERATION
INDICATOR description), if you don't want to change anything
please press and hold P button (until one of the two letters appears
on the display).
3. You switched to NaturalDry Control Menu, you could change status
of NaturalDry functionality by pressing P button:
E – enabled
d – disabled
To confirm the change and exit from the Control Menu please press and
hold P button (3 sec).
Advertisement
Table of Contents
